Search

OBJECTIVE: The occlusal patterns are key requirements for the clinical success of oral rehabilitation supported by implants. This study compared the stresses generated by the disocclusion in the canine guide occlusion (CGO) and bilateral balanced occlusion (BBO) on the implants and metallic infrastructure of a complete Brånemark protocol-type denture modified with the inclusion of one posterior short implant on each side. MATERIAL AND METHODS: A three-dimensional model simulated a mandible with seven titanium implants as pillars, five of them installed between the mental foramen and the two posterior implants, located at the midpoint of the occlusal surface of the first molar. A load of 15 N with an angle of 45° was applied to a tooth or distributed across three teeth to simulate the CGO or BBO, respectively. The commercial program ABAQUS® was used for the model development, before and after the processing of the data. The results were based on a linear static analysis and were used to compare the magnitude of the equivalent stress for each of the simulations. RESULTS: The results showed that the disocclusion in CGO generated higher stresses concentrated on the working side in the region of the short implant. In BBO, the stresses were less intense and more evenly distributed on the prosthesis. The maximum stress found in the simulation of the disocclusion in CGO was two times higher than that found in the simulation of the BBO. The point of maximum stress was located in the neck of the short implant on the working side. CONCLUSIONS: Under the conditions of this study, it was concluded that the BBO pattern was more suitable than CGO for the lower complete denture supported by implants without free distal ends.

The purpose of this study was to evaluate the microhardness of dental enamel around composite restorations bonded with fluoride-containing adhesive systems (FCAS), after thermo- and pH-cycling protocols. Standardized cylindrical cavities were prepared on enamel surfaces of 175 dental fragments, which were randomly assigned into seven experimental groups (n=25). Four groups used FCAS: Optibond Solo (OS); Prime&Bond 2.1 (PB); Syntac Sprint (SS) and Tenure Quick (TC). Other groups consisted of "Sandwich" technique restoration (STR) (glass ionomer liner + hydrophobic adhesive resin /restorative composite) or used Single Bond with (SB) or without (SBWC) cycling protocols. Adhesive systems were applied according to manufacturers' instructions and cavities were restored with a microfilled composite (Durafill VS). After finishing and polishing, all groups were submitted to 1,000 thermal cycles (5 ºC and 55 ºC) and to demineralization (pH 4.3) and remineralization (pH 7.0) cycling protocols, except for SBWC group. The Knoop microhardness of enamel surfaces were measured around restorations. Indentations were recorded at 150, 300 and 450-mm from the cavity wall. Data were analyzed by two-way ANOVA and Duncan's Test (a=0.05%). Means ± SD of enamel microhardness for the groups were (Kg/mm²): SBWC: 314.50 ± 55.93ª ; SB: 256.78 ± 62.66b; STR: 253.90 ± 83.6b; TQ: 243.93 ± 68.3b; OS: 227.97 ± 67.1c; PB: 213.30 ± 91.3d; SS: 208.73 ± 86.6d. Means ± SD of microhardness for the distances 150, 300, 450mm from the cavity wall were, respectively: 234.46 ± 77.81ª; 240.24 ± 85.12ª; 262.06 ± 79.46b. SBWC group, which was not submitted to thermo- and pH-cycling protocols, showed the highest enamel microhardness mean value and the FCAS resulted in lower microhardness values. At 450 mm from the cavity wall, the enamel microhardness increased significantly.O objetivo deste estudo foi avaliar a microdureza do esmalte dental ao redor de restaurações em compósito que utilizaram sistemas adesivos contendo fluoretos (FCAS), após tratamento dessas superfícies restauradas aos protocolos de ciclagem térmica e pH. Cavidades cilíndricas padronizadas foram preparadas em 175 superfícies de esmalte de fragmentos dentais, os quais foram aleatoriamente divididos em sete grupos (n=25). Quatro grupos utilizaram os FCAS: Optibond Solo (OS); Prime&Bond 2.1 (PB); Syntac Sprint (SS) e Tenure Quick (TC). Outros grupos consistiram em restaurações "Sandwich" (STR - ionômero de vidro como base + restauração em composíto) ou utilizaram Single Bond com (SB) ou sem (SBWC) ciclagens. Os sistemas adesivos foram aplicados segundo as instruções dos fabricantes e as cavidades restauradas com compósito microparticulado (Durafill VS). Após o acabamento e polimento, todos grupos foram submetidos a 1.000 ciclos térmicos (5 ºC e 55 ºC) e a um protocolo de ciclagem de pH (desmineralização-pH 4,3 e remineralização-pH 7,0), exceto para o grupo SBWC. A microdureza das superfícies de esmalte foi mensurada ao redor das restaurações. Indentações foram feitas nas distâncias de 100, 300 and 450-mm da parede cavitária. Os dados foram analisados pela ANOVA (2 fatores) and Teste de Duncan (5%). Os valores médios ± DP da microdureza do esmalte para os grupos foram (Kg/mm²): SBWC: 314,50 ± 55,93ª ; SB: 256,78 ± 62,66b; STR: 253,90 ± 83,6b; TQ: 243,93 ± 68,3b; OS: 227,97 ± 67,1c; PB: 213,30 ± 91,3d; SS: 208,73 ± 86,6d. As médias ± DP de microdureza para as distâncias 150, 300, 450 mm da parede cavitária foram, respectivamente: 234,46 ± 77,81ª; 240,24 ± 85,12ª; 262,06 ± 79,46b. O grupo SBWC que não foi submetido aos protocolos de ciclagem térmica e pH mostrou a maior média de microdureza do esmalte e os FCAS resultaram nos menores valores de microdureza. Na distância de 450 mm da parede cavitária, a microdureza apresentou aumento significativo.