Search

The magnetic anisotropy of SmCo-based permanent magnetic thin films are generally controlled by introducing buffer layer or heating substrate. However, the design for the multi-layer thin film system is complicated and the thickness of SmCo is limited due to a short range of interfacial stress/strain between the buffer layer and SmCo layer. In this work, the effects of temperature gradients, generated by RTP (rapid thermal process), on the magnetic anisotropy of the SmCo-based films were systematically investigated. The results show that the as-deposited films exhibit amorphous state. The out-of-plane coercivity of RTP-treated films is strongly correlated with the heating rate, and its optimum value (2810 Oe) is larger than that of the CTA (conventional thermal annealing) treated films (1670 Oe). For the RTP-treated films, the intensity of characteristic diffraction peaks for in-plane oriented SmCo5 (200) and Sm2Co17 (300) decreases, together with reducing the roughness. Besides, the grain size is finer and the contrast of magnetic domains becomes stronger for the RTP-treated films due to that the easy axis of SmCo5/Sm2Co17 phase gradually changes from in-plane to out-of-plane direction. It is suggested that the RTP treatment with a shorter annealing time has beneficial effects on obtaining finer microstructure and improving the out-of-plane magnetic anisotropy of the SmCo-based films. This work provides a novel way to control the magnetic anisotropy via annealing temperature gradients for permanent magnetic thin films, compared with conventional methods, to induce the magnetic anisotropy.

The relation between the microstructure and the magnetic properties of Fe2P-type (Mn,Fe)2(P,Si,B) based materials has been systematically investigated by changing the annealing temperature and time. X-ray diffraction, Scanning Electron Microscopy and Energy Dispersive X-ray Spectroscopy measurements show that the alloys contain the main Fe2P-type phase and two impurity phases of (Fe,Mn)5Si3-type and Fe2MnSi-type. Boron appears to facilitate the formation of the Fe2P-type phase during the arc-melting progress. Upon increasing the annealing temperatures from 1123 to 1423 K, the Curie temperature (TC) decreases from 302.0 to 270.5 K in the Mn1.15Fe0.85P0.55Si0.45 alloys and the magnetic-entropy change (ΔSM) increases linearly with annealing temperature. For the Mn1.15Fe0.85P0.52Si0.45B0.03 alloys annealed at 1423 K for different times, TC decreases from 263.8 and 232.8 K with increasing annealing time and ΔSM reaches a maximum value after annealing for 48 h. The differences in the annealing temperature and time influence the Si content in the Fe2P-type phase of the alloys and determine TC, the thermal hysteresis and the magneto-elastic transition.

This study presents a hierarchical MCMB/CuO/Cu anode structure with super-hydrophilic CuO substrate and blind-hole structures (BHSs) for lithium-ion battery (LIB) application. The porous hierarchical CuO clusters with controllable morphology and super hydrophilicity are prepared and combined with the BHSs on the surface of copper plates (CPs). Results indicate that the new anode yields a considerable improvement in reversible capacity and robustness under the condition of rate cycles. Compared with the conventional pattern of MCMB/Cu, the MCMB/CuO/Cu anode with BHSs produces reversible initial discharge and charge capacities of 381.5 and 347 mAh g−1 at a constant current of 0.5 mA. After 30 cycle times, the battery retains 276.7 and 276.6 mAh g−1, which amounts to 5 times as much as that of 0.5 C rate cycles. The energy density of the battery can be also greatly promoted. The larger surface area and porosity of the new anode facilitate formation of contact interface between the active material and current collector (CC). It also helps shorten the diffusion path of Li-ions and alleviate the volume expansion during the insertion and desertion processes of Li-ions.

Amorphous (FexNiyCoz)80B10Si2Cu1Zr7 (x + y + z = 1) alloys were prepared by melt spinning. By investigating the glass-forming ability, thermal behavior, crystallization and magnetic properties of alloy ribbons, detailed and integral pseudoternary diagrams of (FexNiyCoz)80B10Si2Cu1Zr7 alloys were constructed, which can make one clearly understand the effects of ferromagnetic elements (Fe, Co, Ni) on microstructure and physical properties. Results show that, all as-spun alloys show a fully amorphous structure and the coercivity (Hc) can be tuned to a lower value than 45 A/m. After being annealed, alloys with Ni content lower than 64 at.% (y

The Fe78Si13B9 amorphous alloy ribbons and high-entropy amorphous alloy ribbons of (FeCoNi)78Si13B9 were prepared by melt spinning method. The decolorization performances of these ribbons were investigated in details. It was interesting that Orange Ⅱ solution of 40 mg/L can be degraded almost completely within 70 min and a reduction 52.4% in COD (Chemical Oxygen Demand) value using Fe78Si13B9 amorphous ribbons, indicating the prominent capacity of alloys on the degradation of azo dyes. As for amorphous ribbons (FeCoNi)78Si13B9, they just presented a physical adsorption process, with no chemical degradation of dye molecules under the same conditions. Furthermore, the Fe78Si13B9 amorphous ribbons possess a higher decolorization reaction rate (kobs = 0.071 min−1) compared to the (FeCoNi)78Si13B9 ribbons, together with converting dye molecules to harmless micromolecule inorganic substances, which is of practical significance from the perspective of environmental protection. In addition, all the degradation process in this work fit well with the pseudo-first-order kinetic model. The findings are attractive, valuable and promising for the practical applications and they have important implications in developing Fe-based high-entropy alloys for functional application materials in the field of wastewater treatment.