Search

For most ultralong bus lines, low punctuality rates and vehicle bunching are two main challenges. One potential strategy to solve these two problems is to split an ultralong line into two or three shorter lines according to historical passenger flow patterns as well as other presetting objectives and constraints. Thus, in this paper, a multiobjective optimization model is first established in consideration of both passenger flow distribution and coline metro networks. Then, the optimal truncated stop is determined by estimating the model results generated by enumerating each potential bus stop derived from related metro stops. The nondominated sorting genetic algorithm II (NSGA-II) is applied to solve the model efficiently. A case study conducted on a real bus line associated with metro networks in Beijing, China, demonstrates the efficiency of the optimization strategy adoption in terms of operating cost and passenger travel time, even with a slight increase in passenger cost. Besides, the multivehicle type is also referred in the experiments to verify economic efficiency to reduce operational costs. [ABSTRACT FROM AUTHOR]

Emergencies have a significant impact on the passenger flow of urban rail transit. It is of great practical significance to accurately predict the urban rail transit passenger flow and carry out research on its temporal and spatial distributions under emergency conditions. Urban rail transit operating units currently use video surveillance information mainly to process emergencies and rarely use computer vision technology to analyze passenger flow information collected. Accordingly, this paper proposes a passenger flow-based temporal and spatial distribution model for urban rail transit emergencies based on the CPT. First, this paper clarifies the categories and classification of urban rail transit emergencies, analyzes the factors affecting passenger route selection, and establishes a generalized travel cost model for passengers under emergencies. Second, this paper establishes a passenger route choice behavior model for urban rail transit based on the cumulative prospect theory. Finally, taking Beijing as an example, this paper analyzes passenger travel behavior under emergencies based on multiple logistic regression models and analyzes the impact of emergencies on rail transit travel behavior. The research results show that the cumulative prospect theory can better describe the route choice behavior of rail transit passengers under emergencies than the existing models, and this model is of great significance for handling urban rail transit emergencies. The model proposed in this paper can provide a theoretical basis for the government and relevant departments to formulate traffic management measures. [ABSTRACT FROM AUTHOR]

Carsharing is regarded as a new mode of transportation that can meet the diversity of travel demands. Carsharing systems have different operating modes, and one-way systems are more widely used since cars can be dropped off at any station. However, their planning involves a series of joint decisions regarding the number, size, and location of stations, as well as the fleet size. This paper develops a data-driven mixed-integer linear programming (MILP) model for planning one-way carsharing systems that consider the spatial distribution of demand and the interacting decisions between stations. The characteristics of existing stations and their spatiotemporal correlations are an important part of the model. To solve the MILP model, the extension of the Benders decomposition algorithm is adopted. The practicality of the proposed approach is demonstrated in a case study in Beijing, China. The results show that the existing planning of carsharing could result in a serious waste of resources. In contrast, the proposed method can obtain effective results in a reasonable time. The location results corresponding to a different rate of satisfied demand show that increasing the parking spots to improve the interaction between stations can effectively reduce the cost of operations. It should be noted that this paper only considers the benefit of operators. Future works will be carried out to optimize the one-way carsharing system by considering the benefits of operators, as well as the benefits of users and society. In addition, the impact of COVID-19 will be taken into account in future modeling and case studies. [ABSTRACT FROM AUTHOR]

The development of connected and autonomous vehicle (CAV) technology has received increasing attention in recent years. Although car-following behavior in mixed traffic with CAVs and human-driven vehicles (HDVs) is a core component of microscopic traffic simulation, intelligent traffic systems, etc., the current study of car-following behavior in mixed traffic has some limitations. Furthermore, actual data do not support its applicability to the Chinese traffic environment. To address this gap, this paper designs and organizes a car-following experiment in mixed traffic in Beijing, extracts the trajectory data of CAVs and HDVs based on video recognition, and reconstructs the extracted trajectory data using the Lagrangian theory and Kalman filter theory to ensure the accuracy of the data. Based on this data set, this paper develops an extended car-following model. The model considers the cooperation between drivers by reformulating the prospect theory (PT). The root mean square percentage error (RMSPE) is selected to calibrate and validate the parameters of the proposed model, and the results show that there is significant heterogeneity between CAVs and HDVs in mixed traffic, and the proposed model captures this heterogeneity well. The model presented in this paper provides theoretical support for microscopic traffic simulation in mixed traffic. [ABSTRACT FROM AUTHOR]

Timetable optimization techniques offer opportunity for saving energy and hence reducing operational costs for high-speed rail services. The existing energy-saving timetable optimization is mainly concentrated on the train running state adjustment and the running time redistribution between two stations. Not only the adjustment space of timetables is limited, but also it is hard for the train to reach the optimized running state in reality, and it is difficult to get feasible timetable with running time redistribution between two stations for energy-saving. This paper presents a high-speed railway energy-saving timetable based on stop schedule optimization. Under the constraints of safety interval and stop rate, with the objective of minimizing the increasing energy consumption of train stops and the shortest travel time of trains, the high-speed railway energy-saving timetable optimization model is established. The fuzzy mathematics programming method is used to design an efficient algorithm. The proposed model and algorithm are demonstrated in the actual operation data of Beijing-Shanghai high-speed railway. The results show that the total operating energy consumption of the train is reduced by 3.7%, and the total travel time of the train is reduced by 11 minutes. [ABSTRACT FROM AUTHOR]

Road rescue can provide rescue services for faulty vehicles, such as fuel delivery, tire replacement, battery connection, on-site repair, clearing, and towing, which plays an important role in reducing casualties and property losses in traffic accidents. Based on the historical data of road rescue, this paper analyzes the influencing factors of the road rescue demand and establishes a prediction model of the road rescue demand without data grouping. In order to further improve the prediction accuracy, the data are divided into nine groups according to the importance of the influencing factors, and nine submodels are established for the nine groups of data. When the influencing factors are known, the submodel corresponding to the most important influencing factor is selected to predict the road rescue demand. A case study in Beijing is used to verify the effectiveness and superiority of the proposed models, which can effectively predict the road rescue demand under various conditions, including the normal condition, the Spring Festival, National Day, the three-day holiday (e.g., Qingming, May Day, the Dragon Boat Festival, the Mid-Autumn Festival, and New Year's Day,), and extreme weather (e.g., low temperature, high temperature, heavy snow, heavy rain, and rainstorm). The research findings can provide scientific basis for the rescue department to deploy rescue equipment and rescue personnel in advance, raise the efficiency and quality of rescue, and improve the resilience of the transportation system. [ABSTRACT FROM AUTHOR]

The security travel of freight vehicles is of high societal concern and is the key issue for urban managers to effectively supervise and assess the possible social security risks. With continuous improvements in motion-based technology, the trajectories of freight vehicles are readily available, whose unusual changes may indicate hidden urban risks. Moreover, the increasing high spatial and temporal resolution of trajectories provides the opportunity for the real-time recognition of the abnormal or risky vehicle motion. However, the existing researches mainly focus on the spatial anomaly detection, and there are few researches on the real-time temporal anomaly detection. In this paper, a grid-based algorithm, which combines the spatial and temporal anomaly detection, is proposed for tracing the risk of urban freight vehicles trajectory by considering local temporal window. The travel time probability distribution of vehicle historical trajectory is analyzed to meet the time complexity requirements of real-time anomaly calculation. The developed methodology is applied to a case study in Beijing to demonstrate its accuracy and effectiveness. [ABSTRACT FROM AUTHOR]

A detailed evaluation of the riding environment can help the government master the urban riding environment, identify problematic road sections, and improve riding quality. However, the current evaluation of riding environment is mainly subjective, lacking big data (e.g., shared bicycle trajectory data) as a data-driven objective evaluation system. The emergence of shared bicycle data has provided data support for data-driven riding environment evaluation, but there are few studies using shared bicycle data for riding evaluation at present. First, according to the characteristics of the data and the riding environment, a boxplot method and Bayesian probabilistic network model are used to exclude abnormal data and to match trajectories to road sections. Second, this paper proposes a data-driven evaluation framework based on riding influencing factors. An evaluation framework, which is composed of node-, link-, and block-level evaluation indicators, was constructed, using an evaluation model combining TOPSIS (Technique for Order Preference by Similarity to Ideal Solution) and KNN (K-Nearest Neighbors). The evaluation results can identify parking issues, intersection difficulties, and lane occupancy issues on bicycle sections, and visually reflect the riding environment. The significance of this article is to create an objective evaluation system based on a data-driven technology to accurately identify sections and causes of riding quality problems. The research results can be applied in the future to evaluate the cycling environment around the railway stations for bicycle parking planning and determine the foothold for traffic management. [ABSTRACT FROM AUTHOR]

With increasing energy consumption in urban rail transit systems, researchers have paid significant attention to energy-saving train control. In this paper, we propose an effective train trajectory optimization method to reduce the energy consumption based on coasting control, in which coasting control regimes are added to balance running time and energy consumption. For better determining the starting points of coasting control regimes, the whole train running process is divided into several subintervals. Then, aiming to achieve energy efficiency, coasting regimes are added to the subintervals with high energy-saving effects, in which more energy consumption can be reduced with the same running time addition. Based on this, a coasting control method is proposed to generate energy-saving trajectories considering train dynamics, safety, and punctuality. In addition, the proposed method can solve the multisection energy-saving train trajectory optimization problem to obtain optimal running time schemes and related trajectories. Finally, numerical examples based on one of the Beijing metro lines are implemented to verify the effectiveness of the proposed method. The results show that, for the single-section train control problem, the proposed coasting control algorithm can achieve significant energy-saving effects compared to the practical trajectory and calculate energy-saving trajectory in shorter computation times compared to the dynamic programming method. Meanwhile, for the multisection train control problem, energy consumption can be further reduced by optimizing trajectories and running times integratedly. [ABSTRACT FROM AUTHOR]

The metro system plays a very important role in the urban multimodal transportation system, yet it is susceptible to accidents. A well-designed metro system needs to provide alternative routes to travellers both in the disruptive events and the normal operating conditions for providing rerouting opportunities and balancing crowded lines. This paper provides a new dimension of assessing metro network performance—travellers' route redundancy (or route diversity), which is defined as the number of behaviourally effective routes between each origin-destination (O-D) pair in the network. The route redundancy of metro network is evaluated by statistical indicators of the distribution of the O-D-level number of effective routes. Compared with the existing connectivity and accessibility measures of topology network performance, route redundancy is also based on the topology network, but it takes the travellers' route choice into consideration. Specifically, the effective routes between each O-D pair would provide disaggregated information from the travellers' perspective. Case studies in four metropolises in the world, i.e., Shanghai, Beijing, London, and Tokyo, are conducted to examine the predisaster preparedness of the four metro networks explicitly from the perspective of route redundancy. The results indicate that the London metro network has the best route redundancy performance in terms of the statistical indicators of the distribution of the O-D level number of effective routes. Furthermore, the results of route redundancy are compared with typical measures of topology network performance in terms of measuring connectivity and accessibility of metro networks. Their differences are attributed to the fact that the route redundancy measure considers the travellers' O-D-level route choice beyond the pure network topology and the shortest path considerations of the existing measures. The route redundancy proposed in this paper could assist in evaluating the predisaster preparedness of current or planning metro networks from O-D level to network level. [ABSTRACT FROM AUTHOR]

Urban mobility pattern recognition has great potential in revealing human travel mechanism, discovering passenger travel purpose, and predicting and managing traffic demand. This paper aims to propose a data-driven method to identify metro passenger mobility patterns based on Automatic Fare Collection (AFC) data and geo-based data. First, Point of Information (POI) data within 500 meters of the metro stations are captured to characterize the spatial attributes of the stations. Especially, a fusion method of multisource geo-based data is proposed to convert raw POI data into weighted POI data considering service capabilities. Second, an unsupervised learning framework based on stacked auto-encoder (SAE) is designed to embed the spatiotemporal information of trips into low-dimensional dense trip vectors. In detail, the embedded spatiotemporal information includes spatial features (POI categories around the origin station and that around the destination station) and temporal features (start time, day of the week, and travel time). Third, a density-based clustering algorithm is introduced to identify passenger mobility patterns based on the embedded dense trip vectors. Finally, a case of Beijing metro network is used to verify the feasibility of the above methodology. The results show that the proposed method performs well in recognizing mobility patterns and outperforms the existing methods. [ABSTRACT FROM AUTHOR]

Urban public transit has been rapidly developed in recent years. However, given increases in travel volume, the level of service still needs to be improved to meet the satisfaction of passengers. Transit service providers and researchers have focused on improving transit devices, but the service level of public transit has not yet been effectively improved, so more and more research is interested in analyzing the travel patterns of passengers. Compared with traditional survey methods, smart card collection systems—which can collect spatial-temporal information about passengers' trips—are convenient for the study of bus and subway passengers' travel patterns. However, the data provided by smart cards have not yet been fully explored. Therefore, this paper proposed a multistep methodology to gather information on the travel patterns of bus and subway passengers in Beijing, China. We conducted statistical analyses and used an unsupervised clustering method to study and classify passengers based on travel patterns. Four groups have been identified: standard commuters, flexible commuters, and two types of low-frequency passengers. Then, a comprehensive analysis was conducted. We also discussed the changes of passengers' travel time consumption before and after the implementation of customized bus for high-frequency passengers. The analyses indicated that passengers' travel patterns can provide useful information for transit service providers and can help improve the level of service of urban public transit by promoting the promulgation of local public transport policies and the implementation of customized services. [ABSTRACT FROM AUTHOR]

In rainy weather, the accurate prediction of traffic status not only helps road traffic managers to formulate traffic management methods but also helps travelers design travel routes and even adjust travel time. In this paper, based on six-dimensional data (e.g., past and present spatiotemporal traffic status, road network structure, pavement type, water accumulation, and rainfall level), a fuzzy neural network (FNN) prediction system is proposed to predict traffic status. The traffic status evolution trend is related not only to the existing traffic but also to the new traffic demand. Therefore, the FNN prediction system designed includes offline and online parts using the data of the past and the day separately and avoids the forecast of new traffic demand. The fuzzy C-means clustering algorithm is applied to cluster traffic status data under similar rainy weather in the past to form an offline initial dataset, which is used to train FNN weight parameters. The online part uses real-time detection data and the parameters trained by the offline part to further predict the traffic status and returns the prediction errors to the offline part to correct the weight parameters to further improve prediction accuracy. Finally, the FNN prediction system is verified using real Beijing expressway network data. The verification results show that the prediction system can guarantee prediction accuracy and can be used to effectively identify traffic status. [ABSTRACT FROM AUTHOR]

In a multimodal public transport network, transfers are inevitable. Planning and managing an efficient transfer connection is thus important and requires an understanding of the factors that influence those transfers. Existing studies on predicting passenger transfer flows have mainly used transit assignment models based on route choice, which need extensive computation and underlying behavioral assumptions. Inspired by studies that use network properties to estimate public transport (PT) demand, this paper proposes to use the network properties of a multimodal PT system to explain transfer flows. A statistical model is estimated to identify the relationship between transfer flow and the network properties in a joint bus and metro network. Apart from transfer time, the number of stops, and bus lines, the most important network property we propose in this study is transfer accessibility. Transfer accessibility is a newly defined indicator for the geographic factors contributing to the possibility of transferring at a station, given its position in a multimodal PT network, based on an adapted gravity-based measure. It assumes that transfer accessibility at each station is proportional to the number of reachable points of interest within the network and dependent on a cost function describing the effect of distance. The R-squared of the regression model we propose is 0.69, based on the smart card data, PT network data, and Points of Interest (POIs) data from the city of Beijing, China. This suggests that the model could offer some decision support for PT planners especially when complex network assignment models are too computationally intensive to calibrate and use. [ABSTRACT FROM AUTHOR]

In the rapidly changing multimodal transportation market, not only the obligation in providing train services but also the responsibility in helping other transportation modes to meet emergencies are instrumental for maximizing the generalized benefit of railway companies, leading to an increased utilization. This paper proposes an optimization framework, which includes multiple dispatching measures of arranging residual seats, modifying stopping plans, and inserting additional trains, to design a rescheduling operation plan on a high-speed rail corridor to meet the passenger demand of unexpected large passenger flow (ULPF), which is generated from the disruption of other transportation modes. Considering the revenues of shifting passengers and the costs of the three dispatching measures as two objectives, we formulate a linear integer programming (LIP) model by employing a time-space network to obtain an optimization rescheduling operation plan. Several experiments based on the Beijing-Shanghai high-speed railway corridor are conducted to evaluate the effectiveness and efficiency of the proposed model. The experimental results demonstrate that the proposed model can be used to obtain a reasonable rescheduling operation plan for serving the passengers from ULPF within an acceptable calculation timeframe. [ABSTRACT FROM AUTHOR]

Electricity consumption of metro stations increases sharply with expansion of a metro network and this has been a growing cause for concern. Based on relevant historical data from existing metro stations, this paper proposes a support vector regression (SVR) model to estimate daily electricity consumption of a newly constructed metro station. The model considers some major factors influencing the electricity consumption of metro station in terms of both the interior design scheme of a station (e.g., layout of the station and allocation of facilities) and external factors (e.g., passenger volume, air temperature and relative humidity). A genetic algorithm with five-fold cross-validation is used to optimize the hyper-parameters of the SVR model in order to improve its accuracy in estimating the electricity consumption of a metro station (ECMS). With the optimized hyper-parameters, results from case studies on the Beijing Subway showed that the estimating accuracy of the proposed SVR model could reach up to 95% and the correlation coefficient was 0.89. It was demonstrated that the proposed model could outperform the traditional methods which use a back-propagation neural network or multivariate linear regression. The method presented in this paper can be an adequate tool for estimating the ECMS and should further assist in the delivery of new, energy-efficient metro stations. [ABSTRACT FROM AUTHOR]

Traffic prediction is the cornerstone of intelligent transportation system. In recent years, graph neural network has become the mainstream traffic prediction method due to its excellent processing ability of unstructured data. However, the network relationship in the real world is more complex. Multiple nodes and various associations such as different types of stations and lines in rail transit always exist at the same time. In an end-to-end model, the training accuracy will suffer if the same weights are assigned to multiple views. Thus, this paper proposes a framework with multi-view and multi-layer attention, which aims to solve the problem of node prediction involving multiple relationships. Specifically, the proposed model maps multiple relationships into multiple views. A graph convolutional neural network of multiple views with multi-layer attention learns the optimal regression of nodes. Furthermore, the model uses an autoencoder module to alleviate the over-smoothing problem during the training phase. With the historical dataset of Beijing rail transit, the experiment proves that the prediction accuracy of the model is generally better than the baseline traffic prediction algorithms. [ABSTRACT FROM AUTHOR]

In order to tackle the congestion and environmental issues, customized bus services are proposed and deployed in metropolitan areas. As emerging public transportation services, customized bus services bring passengers more convenience and accessibility. Besides, conventional customized bus services generally organize homogeneous fleet and single location selection to passengers. In this paper, to enhance the mobility and flexibility of customized buses and increase companies' profit, we propose a new form of customized bus service with heterogeneous fleets and multiple candidate locations. First, a mixed-integer programming model (MIP) is developed to describe the customized bus problem. Compared with the conventional model, the proposed MIP is involved in the case of one passenger with multiple candidate pickup or delivery locations and can be solved by GUROBI on small scale, quickly and efficiently. Second, an improved adaptive large neighborhood search algorithm ( ALNS i p ) is utilized to address the large-scale problem more efficiently. Time slack calculation method is then designed to optimize vehicle timetables, which provides stable and excellent performance for searching feasible solutions. In addition, we propose two inserting operators to deal with the problem with multiple candidate locations and analyse its influence on the results. Finally, we test the performance of the proposed model and algorithm on the numerical experiments. And they are verified the effectiveness and implication in a small-scale case on a simplified Sioux waterfall network and a large-scale problem in Beijing, China. The result shows that ALNS i p outperforms other algorithms in searching for more satisfying solutions with higher efficiency. However, the GUROBI solver can obtain the solution to small-scale problems within a shorter time than ALNS i p . Furthermore, it can be suggested that the heterogeneous fleets service with multiple candidate locations is helpful to facilitate collaboration among vehicles and optimize pickup and delivery routes in consequence. [ABSTRACT FROM AUTHOR]

Large-scale activities such as the Winter Olympics are usually held in areas with low temperature or other harsh environments, which greatly affects the spectating experience of pedestrians. In order to improve the travel efficiency and reduce the safety risk of pedestrians, an adaptive information-distribution strategy of VMS (variable message sign) for road networks is proposed to guide the pedestrians. In the proposed strategy, the dynamic feedback mechanism between the VMS information distribution and the state of crowded pedestrians is established, and the dynamic optimization model of the VMS information release layout is formulated. To evaluate the effectiveness of the strategy, a multiagent-based simulation method is proposed. Through numerical simulation, it is found that the guidance strategy can improve the movement efficiency by adjusting releasing duration of VMS information or improving the information obedience rate of pedestrians. In this paper, a large-scale competition area in the Xiaohaituo Mountain in Beijing was taken as an example to simulate the scenarios of ingress and egress with and without the strategy. The results show that the average walking time and the road congestion can be significantly reduced in the road network with the strategy, and the proportion of pedestrians with shorter travel time can be increased. Therefore, the research can provide theoretical foundation and data support for managers to guide passenger flows and improve the spectating experience. [ABSTRACT FROM AUTHOR]

In urban rail transit systems, train scheduling plays an important role in improving the transport capacity to alleviate the urban traffic pressure of huge passenger demand and reducing the operation costs for operators. This paper considers the train scheduling with short turning strategy for an urban rail transit line with multiple depots. In addition, the utilization of trains is also taken into consideration. First, we develop a mixed integer nonlinear programming (MINLP) model for the train scheduling, where short turning train services and full-length train services are optimized based on the predefined headway obtained by the passenger demand analysis. The MINLP model is then transformed into a mixed integer linear programming (MILP) model according to several transformation properties. The resulting MILP problem can be solved efficiently by existing solvers, e.g., CPLEX. Two case studies with different scales are constructed to assess the performance of train schedules with the short turning strategy based on the data of Beijing Subway line 4. The simulation results show that the reduction of the utilization of trains is about 20.69%. [ABSTRACT FROM AUTHOR]

Railway transport becomes a more popular transportation in many countries due to its large transport capacity, low energy consumption, and benign environment. The passenger train service planning is the key of the rail operations system to balance the transport service and the passenger demand. In this paper, we propose a mixed binary linear programming formulation for the passenger train service planning to optimize the train route, frequency, stop schedule, and passenger assignment simultaneously. In addition, we analyze the computational complexities of the model and develop a Benders decomposition algorithm with valid inequalities to solve this problem. Finally, our model and algorithm are tested on a real-world instance of the Beijing-Shanghai high-speed railway line. The computational results show that our approach can solve these problems within reasonable solution time and small optimality gaps (less than 2.5%). [ABSTRACT FROM AUTHOR]

The metro system is an important component of the urban transportation system due to the large volume of transported passengers. Hub stations connecting metro and high-speed railway (HSR) networks are particularly critical in this system. When HSR trains are delayed due to a disruption on the HSR network, passengers of these trains arriving at the hub station at night may fail to get their last metro connection. The metro operator can thus decide to schedule extra metro trains at night to serve passengers from delayed HSR trains. In this paper, we consider the extra metro train scheduling problem in which the metro operator decides how many extra metro trains to dispatch and their schedules. The problem is complex because (i) the arrival of delayed HSR trains is usually uncertain, and (ii) the operator has to minimize operating costs (i.e., number of additional trains and operation-ending time) but maximize the number of served passengers, which are two conflicting objectives. In other words, the problem we consider is stochastic and biobjective. We formulate this problem as a two-stage stochastic program with recourse and use an epsilon-constrained method to find a set of nondominated solutions. We perform extensive numerical experiments using realistic instances based on the Beijing metro network and two HSR lines connected to this network. We find that our stochastic model outperforms out-of-sample a deterministic model that relies on forecasts of the delay by a range of 3–5%. Moreover, we show that our solutions are nearly optimal by computing a perfect information dual bound and obtaining average optimality gaps below 1%. [ABSTRACT FROM AUTHOR]

In this paper, we present a traffic cyber physical system for urban road traffic signal control, which is referred to as UTSC-CPS. With this proposed system, managers and researchers can realize the construction and simulation of various types of traffic scenarios, the rapid development, and optimization of new control strategies and can apply effective control strategies to actual traffic management. The advantages of this new system include the following. Firstly, the fusion architecture of private cloud computing and edge computing is proposed for the first time, which effectively improves the performance of software and hardware of the urban road traffic signal control system and realizes information security perception and protection in cloud and equipment, respectively, within the fusion framework; secondly, using the concept of parallel system, the depth of real-time traffic control subsystem and real-time simulation subsystem is realized. Thirdly, the idea of virtual scene basic engine and strategy agent engine is put forward in the system design, which separates data from control strategy by designing a general control strategy API and helps researchers focus on control algorithm itself without paying attention to detection data and basic data. Finally, considering China, the system designs a general control strategy API to separate data from control strategy. Most of the popular communication protocols between signal controllers and detectors are private protocols. The standard protocol conversion middleware is skillfully designed, which decouples the field equipment from the system software and achieves the universality and reliability of the control strategy. To further demonstrate the advantages of the new system, we have carried out a one-year practical test in Weifang City, Shandong Province, China. The system has been proved in terms of stability, security, scalability, practicability and rapid practice, and verification of the new control strategy. At the same time, it proves the superiority of the simulation subsystem in the performance and simulation scale by comparing the different-scale road networks of Shunyi District in Beijing and Weifang City in Shandong Province. Further tests were conducted using real intersections, and the results were equally valid. [ABSTRACT FROM AUTHOR]

With the recent emergence of big data, there has been significant progress in the study of big data mining and rapid developments in urban computing. With the integration of planning and management in urban areas, there is an urgent need to focus on the identification of urban functional areas (UFAs) based on big data. This paper describes the concept of communication activity intensity, which is more meaningful than the number of communication activities or the user density in identifying UFAs. The impact of diverse geographical area subdivisions on the accuracy of UFA recognition is discussed, and a k-means clustering method for dynamic call detail record data and kernel density estimation technique for static point of interest data are established at the traffic analysis zone level. A case study on the region within Beijing's 3rd Ring Road is conducted, and the results of UFA identification are qualitatively and quantitatively verified. The causes of large passenger flows on certain metro lines in Beijing are also analyzed. The highest identification accuracy is obtained for park and scenery areas, followed by residential areas and office areas. In conclusion, the proposed method offers a significant improvement over the identification accuracy of previous techniques, which verifies the reliability of the method. [ABSTRACT FROM AUTHOR]

The HOV carpooling lane offers a feasible approach to alleviate traffic congestion. The connected vehicle environment is able to provide accurate traffic data, which could optimize the design of HOV carpooling schemes. In this paper, significant tidal traffic flow phenomenon with severe traffic congestion was identified on North Beijing road (bidirectional four-lane) and South Huaihai road (bidirectional six-lane) in Huai'an, Jiangsu Province. The historical traffic data of the road segments were collected through the connected vehicle environment facilities. The purpose of this study is to investigate the effect of adopting two HOV schemes (regular HOV scheme and reversible HOV carpooling scheme) on the urban arterial road under connected vehicle environment. VISSIM was used to simulate the proposed two HOV carpooling schemes at the mentioned road segment. The simulation results showed that the reversible HOV carpooling scheme could not only mitigate the traffic congestion caused by traffic tidal phenomenon but also improve the average speed and traffic volume of the urban arterial road segment, while the regular HOV scheme may exert a negative impact on the average speed and traffic volume on the urban arterial road segment. [ABSTRACT FROM AUTHOR]

It is a dangerous behaviour for pedestrians and nonmotorized vehicles to cross intersections without waiting when they arrive at intersections during the red-light period. This paper investigates three typical signalized major-major intersections in the center of Beijing, by collecting and analyzing 1368 samples of pedestrians and nonmotorized vehicles. A random parameter logit model (RPLM) is established, with immediate red-light running (IRLR) behaviour as the dependent variable. The results show that the number of people waiting upon arrival, number of people crossing upon arrival, traffic mode, motor vehicle phase upon arrival, and speed change upon arrival have significant effects on IRLR behaviour. Accordingly, we suggest enforcing education administration on cyclists to reduce cyclists' IRLR behaviour. Thus, people's red-light running (RLR) behaviour will further decrease with fewer cyclists' IRLR behaviour. [ABSTRACT FROM AUTHOR]

Urban open places with a public service function (e.g., urban parks) are likely to be populated in peak hours and during public events. To mitigate the risk of overcrowding and even events of stampedes, it is of considerable significance to realize a real-time full coverage estimate of the population density. The main challenge has been the limited deployment of crowd surveillance detectors in open public spaces, leading to incomplete data coverage and thus impacting the quality and reliability of the density estimation. To remedy this issue, this paper proposes a modified inverse distance weighting (IDW) method, named the inverse distance weighting based on path selection behavior (IDWPSB) method. The proposed IDWPSB method adjusts the distance decay effect according to visitors' path selection behavior, which better characterizes the human dynamics in open spaces. By implementing the model in a real-world road network in the Shichahai scenic area in Beijing, China, the study shows a decrease in the absolute deviation by 17.62% comparing the results between the new method and the traditional IDW method, justifying the effectiveness of the new method for spatial interpolation in open public places. By considering the behavioral factor, the proposed IDWPSB method can provide insights into public safety management with the increasing availability of data derived from location-based services. [ABSTRACT FROM AUTHOR]

In China, many cities are building themselves the transit metropolis, and the reasonable evaluation of level of service (LOS) of public transport system (PTS) is one important aspect. However, to determine the overall LOS is hard because the distribution of service in PTS is not homogeneous with regard to time and space. To address this problem, this study proposes a general framework to determine the LOS scale of PTS based on the distribution of service quality. Under the framework, two classification methods are discussed. Method 1 uses two parameters, the mean and coefficient of variation to model the distribution, and Method 2 is an existing approach that only considers mean. Then the specific use of the framework is expounded for the service attribute of crowding, and Beijing subway line LOS is evaluated. The line LOS is divided into I–IV, whose threshold is expressed as a function of mean and coefficient of variation. The results show that 57.8% of the sample points are in the most crowding level IV in morning peak hours by Method 1, but 60.9% of sample points are in a comfortable level II by Method 2, and the former is more consistent with reality. In addition, it reveals which lines and time periods need to improve the service level. The research proves the feasibility of considering the service distribution to determine the overall LOS of PTS, and it is useful for capturing more detailed information of the system performance in time and space. This research can provide an approach for evaluating and helping to improve the overall service level of PTS for public transport authorities. [ABSTRACT FROM AUTHOR]

The primary objective of this paper is to demonstrate and validate the necessity of reforming Beijing to a public transit oriented (PTO) city from the view of transportation equity. Equity is believed to be of significant importance to the development of sustainable transportation. This paper presents a comparison of the transportation structure in Beijing with that in other big cities around the world using Cluster Analysis. To accomplish the objective, a road spatial recourse analyzing model is used. This model describes how to distribute road spatial resources fairly to private cars, taxies, and buses. Furthermore, a survey on the satisfactory degree about the first bus rapid transit (BRT) line in Beijing from 8 aspects was conducted. An average score between 4.5 and 3.5 out of 5 demonstrates that the residents are satisfied with the BRT line. Results of this study show the feasibility and creditability in applying PTO transportation structure in Beijing. It is emphasized that more attention should be paid to public transit and it should be the orientation of Beijing's transportation system developed for the consideration of transportation equity. Copyright © 2010 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

In view of the fact that the density-based clustering algorithm is sensitive to the input data, which results in the limitation of computing space and poor timeliness, a new method is proposed based on grid information entropy clustering algorithm for mining hotspots of taxi passengers. This paper selects representative geographical areas of Nanjing and Beijing as the research areas and uses information entropy and aggregation degree to analyze the distribution of passenger-carrying points. This algorithm uses a grid instead of original trajectory data to calculate and excavate taxi passenger hotspots. Through the comparison and analysis of the data of taxi loading points in Nanjing and Beijing, it is found that the experimental results are consistent with the actual urban passenger hotspots, which verifies the effectiveness of the algorithm. It overcomes the shortcomings of a density-based clustering algorithm that is limited by computing space and poor timeliness, reduces the size of data needed to be processed, and has greater flexibility to process and analyze massive data. The research results can provide an important scientific basis for urban traffic guidance and urban management. [ABSTRACT FROM AUTHOR]

The majority of studies on road traffic flow prediction have focused on the flow of passenger cars or the flow of traffic as a whole, which ignore the significant impact of trucks with different sizes and operational characteristics on traffic flow efficiency. Therefore, in this paper, we focus on truck traffic flow and propose a Multifeatures Spatial-Temporal-Based Neural Network model (M-BiCNNGRU) to improve its prediction. The proposed model not only comprises conventional temporal characteristics and spatial relationships but also includes a range of multifeatures. These multifeatures include policy limit, optimal time delay, road resistance, and traffic congestion state. The impacts of upstream and downstream road sections are considered on the spatial relationship by using a Convolutional Neural Network (CNN). A Bidirectional Gated Recurrent Unit (Bi-GRU) is employed to account for the temporal characteristics. To evaluate the proposed model, traffic flow data were collected from a major expressway in Beijing and the results were compared with those derived from existing models. The results show that the prediction accuracy of the BiCNNGRU model, with spatial-temporal characteristics, and the M-BiGRU model, with multifeatures and temporal, is, respectively, 4.13% and 2.15% greater than that of the Bi-GRU model, with temporal characteristics. The prediction accuracy of the proposed M-BiCNNGRU model is 92.86%, which is 7.12% greater than that of the Bi-GRU model and 13.83% greater than that of the Support Vector Regression (SVR) model. In general, therefore, the proposed M-BiCNNGRU model, which combines multifeatures, temporal characteristics, and spatial relationships, can significantly improve accuracy in predicting truck traffic flow. [ABSTRACT FROM AUTHOR]

This paper proposes a novel approach to identify the key nodes and sections of the roadway network. The taxi-GPS trajectory data are regarded as mobile sensor to probe a large scale of urban traffic flows in real time. First, the urban primary roadway network model and dual roadway network model are developed, respectively, based on the weighted complex network. Second, an evaluation system of the key nodes and sections is developed from the aspects of dynamic traffic attributes and static topology. At the end, the taxi-GPS data collected in Xicheng District of Beijing, China, are analyzed. A comprehensive analysis of the spatial-temporal changes of the key nodes and sections is performed. Moreover, the repetition rate is used to evaluate the performance of the identification algorithm of key nodes and sections. The results show that the proposed method realizes the expression of topological structure and dynamic traffic attributes of the roadway network simultaneously, which is more practicable and effective in a large scale. [ABSTRACT FROM AUTHOR]

Emission around intersections has become an issue in the urban traffic network. This paper aims to investigate the impact of pedestrian and nonmotorized vehicle violations on emissions at mixed-traffic flow intersection based on the volumes of vehicles, nonmotor vehicles, and pedestrians. Also, it focuses on the arterial and collector intersections with high vehicle volume and limited space. Running red light and crossing intersection diagonally are two critical violations, accounting for 91.75% of effective violations (interference with vehicles' operation). In this context, a violation blocking model is developed to estimate the blocking probability for each vehicle based on the volumes of pedestrians and nonmotor vehicles. The model includes two scenarios. (1) Through phase: the violation blocking model of running red light is developed based on the survival curve (the relationship between waiting time and running red light probability). (2) Left-turn phase: the violation blocking model at this phase includes two parts: (i) crossing the intersection diagonally model is developed for the first vehicle and (ii) running red light model is developed for subsequent vehicles. The existing emission model can estimate the emissions based on the blocking positions. In the case study, emissions increase with the vehicle volume approaching the saturated flow rate and the volumes of nonmotor vehicles and pedestrians increasing. Results show that the maximum emission increase of CO (carbon monoxide) for through phase and left-turn phase can reach 16.7% and 36.4%. [ABSTRACT FROM AUTHOR]

This study elaborated an evolutionary game model to optimize the decision-making process on the interaction between civil aviation and high-speed rail under alternative passenger ticket prices (PTPs) and carbon trading prices (CTPs). First, a logit model was used to calculate the passenger flow distribution rate in civil aviation and HSR, and their revenue loss function was determined according to varying PTPs and CTPs. Second, an evolutionary game model with incomplete information was developed to assess the respective revenues. Third, the stable strategy solution of the game model was derived from replicator dynamics, and an investigation of stable conditions under variable cases was performed. Finally, the simulation of a case study on the Beijing–Shanghai corridor was conducted to validate the proposed model's feasibility. The additional revenue is shown to be the key influencing factor, mainly controlling the strategic decisions of airport and high-speed rail companies. Besides, the final strategy was strongly influenced by the alteration of PTPs and CTPs: higher PTPs promoted civil aviation and high-speed rail collaboration, while increased CTPs forced their competing behavior. The results obtained are instrumental in outlining the optimal strategy range for passenger ticket and carbon trading prices, encouraging high-speed transportation system growth. [ABSTRACT FROM AUTHOR]

In order to solve the problem that the railway passenger volume data are abnormal due to holidays and major events interfering with the prediction accuracy, the spline interpolation method is introduced to replace the abnormal passenger volume data. In addition, an improved particle swarm optimization (IPSO) is proposed to optimize the gradient difference acceleration law to combine and improve the predicted value and further improve the prediction accuracy of the railway passenger traffic. Finally, taking Beijing as the research object, the Holt exponential smoothing method and the BP neural network are selected to verify the effect of spline interpolation and IPSO-gradient difference acceleration law on prediction accuracy. The research results show that the spline interpolation method has a better prediction effect after processing abnormal passenger traffic data, and the improved particle swarm algorithm also shows better optimization ability and convergence speed when solving the double difference postulate. In comparison with the BP neural network, Holt exponential smoothing, simple averaging, and conventional redifference approaches, the IPSO-redifference acceleration method achieves a superior prediction performance, and the absolute values of the forecast error are reduced by 3.320%, 1.518%, 2.419%, and 0.602%. [ABSTRACT FROM AUTHOR]

To improve traffic efficiency and utilization of road resources and alleviate traffic congestion caused by imbalance of bidirectional traffic flow, in view of the conversion conditions of reversible lane function, the operating characteristics of associated intersections under dynamic reversible lanes are analysed in terms of capacity, and a reversible lane control model is constructed based on short-term traffic flow prediction. On this basis, the reversible lane segment clearing time and upstream and downstream signal control strategies under different states are studied. The collaborative control model of reversible lane clearing time and signal timing of associated intersections is established to obtain the optimal time for reversible lane function switching. Finally, using Chaoyang Road, Beijing, as an example, the effectiveness of the proposed model is verified by the simulation indexes of average vehicle delay and reversible lane clearing time. The results show that the optimized clearing efficiency exceeds 15% and the optimized average vehicle delay is reduced by more than 10%. Combined with the future traffic state, the traffic capacity and saturation flow are greatly improved, and the intelligent reversible lane control is better achieved. [ABSTRACT FROM AUTHOR]

This paper proposed a new method to describe, compare, and classify the traffic congestion points in Beijing, China, by using the online map data and further revealed the relationship between traffic congestion and land use. The data of the point of interest (POI) and the real-time traffic was extracted from an electronic map of the area in the fourth ring road of Beijing. The POIs were quantified based on the architectural area of the land use; the congestion points were identified based on real-time traffic. Then, the cluster analysis using the attributes of congestion time was conducted to identify the main traffic congestion areas. The result of a linear regression analysis between the congestion time and the land use showed that the influence of the high proportion of commercial land use on the traffic congestion was significant. Also, we considered five types of land use through performing a linear regression analysis between the congestion time and the ratio of four types of land use. The results showed that the reasonable ratio of land use types could efficiently reduce congestion time. This study makes contributions to the policy-making of urban land use. [ABSTRACT FROM AUTHOR]

Owing to the current development trend of globalization and informatization, traditional transportation technologies and means can no longer meet the needs of economic and social development. Thus, intelligent transportation will be an inevitable and revolutionary choice for the development of the transportation industry. As a subsystem of the intelligent transportation system, the electronic nonstop toll collection (ETC) system provides a good solution to the problems of traffic congestion, environmental pollution, energy consumption, and low toll operation efficiency caused by expressway toll collection. This high-technology system is utilized in many fields, such as radio communication and computer and automatic control in the transportation field. China's expressway ETC systems have evident effects on congestion reduction at toll stations. Although the advantages of ETC lanes are significant, and China actively implements ETC-handling policies, some drivers are reluctant to install ETC on-board systems or they have negative experiences after handling them. According to a survey, existing literature lacks research on the factors affecting user satisfaction with ETC. On the basis of the questionnaire data of ETC user experience in Shanghai and Beijing, we comprehensively investigate the reasons of banking, ETC equipment, and drivers' personal factors and travel characteristics to establish an ordinal logistics model. Through cluster analysis, drivers in the two cities are divided into three groups, and the significance of related variables is further analyzed. This research can help us understand the degree of influence of different factors on user satisfaction with ETC to a certain extent. Moreover, effective methods and measures can be used to promote the popularity of ETC vehicle equipment and the utilization rate of ETC-dedicated lanes. [ABSTRACT FROM AUTHOR]

Blind search for available parking space is accountable for most traffic congestion, accident, and pollution in cities, which severely impact people's life. Parking management based on an online smart parking system is practical to alleviate parking problems in which parking allocation is the core. However, existing researches are weak at satisfying allocation effect and speed simultaneously when solving large-scale dynamic parking allocation problem. To address this problem, we firstly construct an online "Collection-Allocation-Response" smart parking system (CARSP) to offer parking services to users and rent parking spaces from owners so as to obtain revenue for system managers. We then propose a novel Doubly Periodic Rolling Horizon allocation approach (DPRH) that circularly conduct allocation within a short period and reallocation within a long period. We formulate a narrow allocation model (without reallocation) and broad allocation model (with reallocation), both of which are binary integer programming models with the objective of maximizing system integrated benefit. We design seven performance metrics to evaluate the overall allocation effect and speed of CARSP based on DPRH. According to the three-day district-level instance in Beijing, CARSP based on DPRH performs excellently in balancing allocation effect and speed. This study is meaningful for constructing and optimizing an online smart parking system. [ABSTRACT FROM AUTHOR]

Demand responsive transit (DRT) is emerging as one of the most potential travel modes to satisfy flexible travel demands. Nevertheless, how to attract more passengers has become a critical problem in the success of DRT projects. It is necessary to take into account the psychological factors impacting passengers' choices. The study proposes a slack departure strategy considering boundedly rational passengers, which introduces passengers' decision-making psychology into the optimization process. The strategy can adjust the departure time of passengers to adjacent time windows. The discount-incentive mechanism is presented to attract passengers to accept the changes while maintaining the quality of service. On this basis, the theory of bounded rationality is applied to describe the decision-making process of passengers. We construct a multiobjective programming model to analyze the operator-passenger interactive effect. To address the multiobjective problem, a two-phase heuristic algorithm is established to get the Pareto solution for the model. A numerical experiment is carried out on the Sioux Falls network. The case study of Beijing is discussed to evaluate the effectiveness of the strategy. The results indicate that the slack departure strategy can significantly benefit both the operators and passengers. The operating profit substantially increases by up to 63%. Meanwhile, the passenger's general travel cost declines by 12%. The optimal discount rate of the incentive mechanism is 20%. Therefore, the study contributes to comprehending the passenger's decision-making psychology and providing a new optimization strategy for the operator of DRT. [ABSTRACT FROM AUTHOR]

With the development of autonomous driving technologies, robo-taxis (shared autonomous vehicles) are being tested on real roads. In China, in particular, people in some cities such as Beijing and Shanghai can book a robo-taxi online and experience the service. To examine the influential factors on user acceptance of robo-taxi services, this study proposes and employs an extended technology acceptance model (TAM) with four external factors: perceived trust, government support, social influence, and perceived enjoyment. Data were collected through an online questionnaire in China, and responses from 403 respondents were analyzed using structural equation modeling. Both typical TAM factors—including perceived ease of use, perceived usefulness, and attitude—and external factors were found to play significant roles in predicting users' intention to use robo-taxis. The four external factors influenced the user acceptance indirectly via typical TAM factors. Improving users' perceived trust is important for increasing public adoption. A greater emphasis by manufacturers on safety concerns, wider dissemination of information on data protection and safety systems, and government support through incentives for manufacturers and users can help improve public adoption of robo-taxi services. [ABSTRACT FROM AUTHOR]

This study proposes a multiobjective mixed integer nonlinear programming model for a last-mile shuttle service to improve bus commuters' travel time reliability. The approach aims to assign the routes that pick up the transit passengers located at the different stops by shuttle service. A bilevel optimization model is established: the upper model of route design considers the tradeoff between time cost and fare cost when some of the passengers take the shuttles, and the lower model assigns the demand of transit passengers. The proposed model effectively captures the reliability of travel time because related parameters are estimated by a statistical fitting test with a large number of real-world bus geographic information system (GPS) data. Moreover, dynamic demand diverting from conventional transit to shuttle service and travel time reliability, including passenger in-vehicle time (IVT) and waiting time (WT), are fully considered in this model. Since the task is a nonlinear programming model, a two-stage algorithm combined with linearization processing is presented to find an optimal solution. Finally, from the case study of Zhongguancun Software Park zone in Beijing, it is indicated that when last-mile shuttle service is provided, bus passengers' travel time reliability of last-mile trips can be improved by 14%. The study can be an important reference for improving the low reliability widely existing in the current transit commuters' last-mile problem. [ABSTRACT FROM AUTHOR]

Urban subway is taken by people in different frequencies, thus leading them to present different dependency varieties on this mode. Yet, how those passengers who possess low dependency on urban subway travel is less investigated. Under this background, we propose a framework to uncover passengers' dependency variety on stations' functions in urban subway. To begin with, nine features regarding travel frequency and time are extracted from 100 million transaction records generated by 11.45 million passengers in a month. Thus, their travel dependency on urban subway is quantified. These features are clustered into 5 distinct levels via the k-means algorithm, before an inference of subway stations' functions from 236,040 POI data sources via the LDA approach. In this way, passengers' travel purposes can be identified. How passengers with different dependency levels behave in subway stations in space and time is further explored in a visualization way. The intuitive experimental results, validated by priori user experiences and land-use plan of Beijing, show that among the 5 levels of dependency varieties, passengers in the first two groups present a relatively strong dependency on urban subway. Meanwhile, passengers in the rest three groups possess a low dependency on urban subway and display extreme travel patterns in time and frequency, greatly increasing management difficulties for transit operators. Findings in this research help distinguish passengers with low levels of subway dependency and grasp how those passengers without striking dependency travel by subway and what for so that practitioners can conduct an accurate risk assessment on them. [ABSTRACT FROM AUTHOR]

A sudden increase in passenger flow can primitively lead to continuous congestion of a subway network and thus have a profound impact on the subway system. To prevent the risk caused by sudden overcrowding, the prediction of passenger flow is a daily task of the rail transit management. Most current short-term passenger flow forecasts rely only on inbound passenger flow, which cannot accurately characterize the total impact of sudden passenger flow. To enhance the prediction accuracy, we propose a sudden passenger flow prediction model with two factors, the outbound and inbound passenger flows. The wavelet neural network (WNN) model was used to detect the sudden passenger flow, and subsequently, it is optimized by the genetic algorithm (GA), according to two-factor data characteristics. Sudden passenger flow events from 2014 to 2016 in the Beijing Dongsishitiao Station (DS) were used to train and verify the reliability of the prediction model. The optimized WNN results proved better than the conventional WNN, and the error of models based on two factors was significantly smaller than the models with a single-factor. [ABSTRACT FROM AUTHOR]

With the development of information and communication technologies (ICTs), considerable attention is being paid to the relationship between ICT use and travel behavior. However, it is unclear whether the effects of ICT use on trip generation vary across travel modes. Based on the data of 1022 respondents collected by a web-based questionnaire survey in Beijing, this study used a zero-inflated Poisson model to investigate the effects of ICT use on trip generation in different travel modes, in which ICT use was measured by both the time spent online and the Internet use frequency. The results indicated that the effects of ICT use on trip generation vary across auto, transit, and active trips. Moreover, two measurements of ICT use play essential roles in influencing a trip generation. Specifically, only the frequency of ordering food online showed a positive association with the likelihood of generating any transit trips. These findings demonstrate the importance of considering the differences across travel modes when analyzing the relationship between ICT use and trip generation. [ABSTRACT FROM AUTHOR]

In order to model air quality in heavy pollution days, a dynamic emission monitoring system is implemented in the Beijing road network, which requires the input of hourly traffic flows. Floating car data (FCD) is increasingly employed for flow estimation based on the fundamental diagrams to supplement data provided by stationary detectors. However, existing studies often used a typical fundamental diagram without considering the hysteresis phenomena and the uncertainty of traffic flow estimation. This study aims to develop a multiperiod fundamental diagram for the traffic flow estimation from FCD considering the hysteresis phenomena. The result shows that the proposed multiperiod fundamental diagram can improve the accuracy of flow estimation. The uncertainty of traffic flow estimation at both 10 minutes and 1 hour is also quantified, and the result indicates that the variation of the estimation uncertainty at 1 hour is lower than that at 10 minutes, with an average 7% reduction of the range of 95% confidence interval (CI). But there is no significant difference in magnitudes of the estimation uncertainty at 1 hour compared with that at 10 minutes. Moreover, the uncertainty for congested flows is lower than that for free flows. In the case study, the proposed model is employed to develop the spatial and temporal distributions of flows and emissions for the metropolitan area in Beijing. [ABSTRACT FROM AUTHOR]

Travel happiness has drawn increasing attention in recent years. However, the empirical research in developing countries' context is very limited, and few studies consider both cognitive and affective evaluations during traveling. This study uses web-based survey data collected in Beijing, China, and applies multiple regression analysis to examine impacts of sociodemographic attributes, travel characteristics, residential environment, mode consonance, self-evaluation, and health conditions, on travel happiness. Satisfaction with Travel Scale (STS) is used to measure travel happiness. Results show that for trips using active travel modes, traveling by walking has higher travel happiness than by nonmotor vehicles. For those trips traveling by motor vehicles, company shuttle bus trips have the highest travel happiness ratings, followed by automobile trips and public transport trips. Transport mode consonance is significantly positively correlated with travel happiness. Residential environment, self-reported optimism, and daily happiness have great positive impacts on travel happiness. Living in suburban areas is more satisfying for walking and car trips, but travel frequency, travel duration, and perceived travel time length have significant negative effects on travel happiness. Public transport use with friends is enjoyable, but unpleasant with work partners. More happiness when listening to music/radio or reading during traveling is demonstrated. Finally, policy implications and potential extended research topics are recommended. [ABSTRACT FROM AUTHOR]

From December 2, 2013, to October 31, 2019 (total 2160 days), Beijing official air quality data was used as the research object. The article analyzes the end of days 4 and 9 and the end of the nonrestricted 4 and 9 days, working and nonworking days, restricted and nonrestricted working days, long holidays (Spring Festival and National Day), and nonlong holidays (short holidays other than the Spring Festival and National Day and working days) of AQI, PM2.5, PM10, SO2, CO, NO2, and O3. According to the statistical analysis of the data, the air quality of the 4 and 9 limit is worse than that of the non-4 and 9 limit. Motor vehicles restricted in traffic had an objective effect on air AQI, PM2.5, PM10, CO, and NO2, whereas there was almost no difference in O3. Some peak values of AQI, PM2.5, PM10, SO2, CO, and NO2 on nonrestricted working days were significantly higher than those on restricted working days. At the same time, there was a peak time of the impact of motor vehicles on AQI, PM2.5, PM10, SO2, CO, and NO2 in Beijing. This time should be between 3 and 5 days, or 72 and 120 hours. [ABSTRACT FROM AUTHOR]

This research aims to calculate PM2.5 concentration on the road network by considering the network-wide traffic status, which can be used to support research about the impact of urban road network pollution concentration on health. The increase in the use and number of vehicles has brought about a large amount of vehicle exhaust emissions and increased urban air pollutants. This is also one of the important reasons why this issue is worth studying. In this research, traffic emission was an estimate based on network-wide traffic status which was calculated from vehicle trajectories and spatial variance-covariance matrix. An identification method of external input pollutants is proposed to determine the occurrence of external pollutants imported into the urban area. To calculate the impact of multiple influencing factors on the pollution concentration of the entire road network, a multivariate linear model was adopted to calculate a variety of influencing factors and calibrate the model parameters by collecting real data. The results show that traffic emissions, external input pollution, and wind impact are the main factors affecting the PM2.5 concentration on urban road networks. Combined with real-time traffic data, we can obtain the temporal and spatial characteristics of the pollutant concentration of the road network. For policymakers, our research can provide a method for calculating the PM2.5 concentration on the road network, which is useful for establishing a health assessment framework in the future. [ABSTRACT FROM AUTHOR]

As a critical foundation for train traffic management, a train stop plan is associated with several other plans in high-speed railway train operation strategies. The current approach to train stop planning in China is based primarily on passenger demand volume information and the preset high-speed railway station level. With the goal of efficiently optimising the stop plan, this study proposes a novel method that uses machine learning techniques without a predetermined hypothesis and a complex solution algorithm. Clustering techniques are applied to assess the features of the service nodes (e.g., the station level). A modified Markov decision process (MDP) is conducted to express the entire stop plan optimisation process considering several constraints (service frequency at stations and number of train stops). A restrained MDP-based stop plan model is formulated, and a numerical experiment is conducted to demonstrate the performance of the proposed approach with real-world train operation data collected from the Beijing-Shanghai high-speed railway. [ABSTRACT FROM AUTHOR]