Search

Mechanical testing is a valuable tool for assessing intervertebral disc health, but the wide range of testing protocols makes it difficult to compare results from different studies. Normalizing mechanical properties by disc geometry allows for such comparisons, but there is little consistency in the methods by which disc geometry is measured. As such, we hypothesized that methods used to measure disc geometry would impact reported mechanical properties. Disc height and area were measured using computed tomography (CT), digital calipers, and ImageJ to yield three different measurements for disc height and six for disc area. Disc heights measured by digital calipers ex situ were >30% less than disc heights measured in situ by CT, and disc areas measured ex situ using ImageJ were >30% larger than those measured by CT. This significantly affected reported mechanical properties, leading to a 65% reduction in normalized compressive stiffness in the most extreme case. Though we cannot quantitatively correct between methods, results presented in this study suggest that disc geometry measurement methods have a significant impact on normalized mechanical properties and should be accounted for when comparing results.

Biomechanical testing methodologies for the spine have developed over the past 50 years. During that time, there have been several paradigm shifts with respect to techniques. These techniques evolved by incorporating state-of-the-art engineering principles, in vivo measurements, anatomical structure-function relationships, and the scientific method. Multiple parametric studies have focused on the effects that the experimental technique has on outcomes. As a result, testing methodologies have evolved, but there are no standard testing protocols, which makes the comparison of findings between experiments difficult and conclusions about in vivo performance challenging. In 2019, the international spine research community was surveyed to determine the consensus on spine biomechanical testing and if the consensus opinion was consistent with the scientific evidence. More than 80 responses to the survey were received. The findings of this survey confirmed that while some methods have been commonly adopted, not all are consistent with the scientific evidence. This review summarizes the scientific literature, the current consensus, and the authors' recommendations on best practices based on the compendium of available evidence.

In vitro mechanical testing of intervertebral discs is crucial for basic science and pre-clinical testing. Generally, these tests aim to replicate in vivo conditions, but simplifications are necessary in specimen preparation and mechanical testing due to complexities in both structure and the loading conditions required to replicate in vivo conditions. There has been a growing interest in developing a consensus of testing protocols within the spine community to improve comparison of results between studies. The objective of this study was to perform axial compression experiments on bovine bone-disc-bone specimens at three institutions. No differences were observed between testing environment being air, with PBS soaked gauze, or a PBS bath (P > .206). A 100-fold increase in loading rate resulted in a small (2%) but significant increase in compressive mechanics (P

Bovine caudal discs have been widely used in spine research due to their increased availability, large size, and mechanical and biochemical properties that are comparable to healthy human discs. However, despite their extensive use, the radial variations in bovine disc composition have not yet been rigorously quantified with high spatial resolution. Previous studies were limited to qualitative analyses or provided limited spatial resolution in biochemical properties. Thus, the main objective of this study was to provide quantitative measurements of biochemical composition with higher spatial resolution than previous studies that employed traditional biochemical techniques. Specifically, traditional biochemical analyses were used to measure water, sulfated glycosaminoglycan, collagen, and DNA contents. Gravimetric water content was compared to data obtained through Raman spectroscopy and differential scanning calorimetry. Additionally, spatial distribution of lipids in the disc's collagen network was visualized and quantified, for the first time, using multi-modal second harmonic generation (SHG) and Coherent anti-Stokes Raman (CARS) microscopy. Some heterogeneity was observed in the nucleus pulposus, where the water content and water-to-protein ratio of the inner nucleus were greater than the outer nucleus. In contrast, the bovine annulus fibrosus exhibited a more heterogeneous distribution of biochemical properties. Comparable results between orthohydroxyproline assay and SHG imaging highlight the potential benefit of using SHG microscopy as a less destructive method for measuring collagen content, particularly when relative changes are of interest. CARS images showed that lipid deposits were distributed equally throughout the disc and appeared either as individual droplets or as clusters of small droplets. In conclusion, this study provided a more comprehensive assessment of spatial variations in biochemical composition of the bovine caudal disc.

Lumbar intervertebral disc herniation, as a leading cause of low back pain, productivity loss, and disability, is a common musculoskeletal disorder that results in significant socioeconomic burdens. Despite extensive clinical and basic scientific research efforts, herniation etiopathogenesis, particularly its initiation and progression, is not well understood. Understanding herniation etiopathogenesis is essential for developing effective preventive measures and therapeutic interventions. Thus, this review seeks to provide a thorough overview of the advances in herniation‐oriented research, with a discussion on ongoing challenges and potential future directions for clinical, translational, and basic scientific investigations to facilitate innovative interdisciplinary research aimed at understanding herniation etiopathogenesis. Specifically, risk factors for herniation are identified and summarized, including familial predisposition, obesity, diabetes mellitus, smoking tobacco, selected cardiovascular diseases, disc degeneration, and occupational risks. Basic scientific experimental and computational research that aims to understand the link between excessive mechanical load, catabolic tissue remodeling due to inflammation or insufficient nutrient supply, and herniation, are also reviewed. Potential future directions to address the current challenges in herniation‐oriented research are explored by combining known progressive development in existing research techniques with ongoing technological advances. More research on the relationship between occupational risk factors and herniation, as well as the relationship between degeneration and herniation, is needed to develop preventive measures for working‐age individuals. Notably, researchers should explore using or modifying existing degeneration animal models to study herniation etiopathogenesis, as such models may allow for a better understanding of how to prevent mild‐to‐moderately degenerated discs from herniating. [ABSTRACT FROM AUTHOR]