Search

Uncontrolled exposure to X-band frequency leads to health damage. One of the principles of radiation protection is shielding. But, conventional shielding materials have disadvantages. Therefore, studies of novel materials, as an alternative to conventional shielding materials, are required to obtain new electromagnetic shielding material. Therefore, this study investigated the electromagnetic shielding of two component epoxy thermosetting resin for the X - band frequency with workplace approach. Two components of epoxy resin mixed according to manufacturing instruction with the weight ratio that was 100:10 .Epoxy plates fabricated in three different thicknesses (2, 4 and 6mm) and shielding effectiveness measured by Vector Network Analyzer. Then, shielding effectiveness measured by the scattering parameters.The results showed that 6mm thickness of epoxy had the highest and 2mm had the lowest average of shielding effectiveness in X-band frequency that is 4.48 and 1.9 dB, respectively. Also, shielding effectiveness increased by increasing the thickness. But this increasing is useful up to 4mm. Percentage shielding effectiveness of attenuation for 6, 4 and 2mm thicknesses is 64.35%, 63.31% and 35.40%. Also, attenuation values for 4mm and 6mm thicknesses at 8.53 GHz and 8.52 GHz frequency are 77.15% and 82.95%, respectively, and can be used as favourite shields for the above frequency. 4mm-Epoxy is a suitable candidate for shielding application in X-band frequency range but, in the lower section, 6mm thickness is recommended. Finely, the shielding matrix can be used for selecting the proper thickness for electromagnetic shielding in X- Band frequency.

Detergents and problems of their attendance into water and wastewater cause varied difficulties such as producing foam, abnormality in the growth of algae, accumulation and dispersion in aqueous environments. One of the reactors was designated with 30% of the media with the similar conditions exactly same as the other which had filling rate about 10 %, in order to compare both of them together. A standard method methylene blue active substance was used to measure anionic surfactant. The concentrations of linear alkylbenzene sulfonate which examined were 50, 100, 200, 300 and 400 mg/l in HRT 72, 24 and 8 hrs. The removal percentage for both of reactors at the beginning of operating at50 mg/l concentration of pollutant had a bit difference and with gradually increasing the pollutant concentration and decreasing Hydraulic retention time, the variation between the removal percentage of both reactors became significant as the reactor that had the filling rate about 30 %, showed better condition than the other reactor with 10 % filling rate. Ideal condition in this experiment was caught at hydraulic retention time about 72 hrs and 200 mg/l pollutants concentration with 99.2% removal by the reactor with 30% filling rate. While the ideal condition for the reactor with 10% filling rate with the same hydraulic retention time and 100 mg/l pollutants concentrations was obtained about 99.4% removal. Regarding anionic surfactant standard in Iran which is 1.5 mg/l for surface water discharge, using this process is suitable for treating municipal wastewater and industrial wastewater which has a range of the pollutant between 100-200 mg/l. but for the industries that produce detergents products which make wastewater containing more than 200 mg/l surfactants, using secondary treatment process for achieving discharge standard is required.

ABSTRACT Microwave is part of the electromagnetic spectrum that has different application such as communications, military, air-traffic Control and etc... Previous studies showed that radar frequency could be a health hazard agent. This review article mentioned some of the studies that investigated non-thermal effects of radar frequencies. Reproductive effects, cancers, blood effects, genetic, adverse immune effects and mental effects are non-thermal effects that presented in this report. There are many unknown aspects of the biological effects and many of them did not determined very well such as oxidative stress and mental effects. Compliance with permissible exposure limits, reduction in exposure, and shielding are some of the controlling methods to protect workers from the exposure of microwave and among them, The use of shielding is a superior method for prevention of microwave exposure and among them, electromagnetic Nano composites shields is appropriate for protection of workers from radar exposure.