Search

A wideband substrate integrated waveguide (SIW) power divider based on half mode analysis is presented in this article. The structure is constructed by two substrate layers and three metal layers. Two symmetrical longitudinal apertures etched on the middle ground are introduced to realize the equal power division, and couple the signal from the SIW to the upper layer output ports simultaneously. Two fork‐type microstrip lines on the top metal layer are used to improve the bandwidth of the power divider. The equivalent circuit based on the half mode analysis method is presented for theoretical analysis and further design of the power divider, and good impedance matching can be obtained accordingly. For demonstration, a power divider prototype with the dimension of 48 × 73 × 1.38 mm3 is designed, fabricated, and measured. Good agreement is observed between the simulated and measured results. The measured return loss of the SIW power divider is better than 12 dB in the frequency range of 6.2 ~ 10.3 GHz, and the insertion loss is around 1.6 dB over the entire frequencies of interest. [ABSTRACT FROM AUTHOR]

A novel 6-port balanced network with high unequal power division ratio using shorted coupled lines is proposed in this letter. The design parameters of the proposed power divider are analyzed according to transmission line theory. Two double-sided parallel-strip line 1808 phase inverters loaded with 4 isolation resistors are used to realize high isolation for the power dividing output ports. A planar balanced network with bandwidth of 40.5% (power division ratio: 1:10) for the differential mode and wideband 23% common mode suppression is designed and fabricated. The measured results show good agreement with the theoretical expectations. [ABSTRACT FROM AUTHOR]

Abstract: Two novel wideband balanced‐to‐unbalanced power dividers based on transmission lines and coupled lines are proposed in this article. Multifunction can be realized without cascading single devices with common mode suppression. The desired power divider configurations can be obtained using the even/odd‐mode characteristic impedance of the coupled lines and characteristic impedance of the transmission lines. A resistor in the middle of two single‐ended ports is used to realize isolation between output ports. Two prototypes of wideband balanced‐to‐unbalanced power dividers operating at 2.3 GHz with differential‐mode bandwidths of 79.6 and 134.1% are designed and fabricated. The theoretical and measured results are in good agreement and show good in‐band performances. [ABSTRACT FROM AUTHOR]

In this article, two novel topologies of compact‐size dual‐band single‐ended‐to‐balanced power dividers that are loaded with open‐ and short‐ended stubs are presented. Quarter‐wavelength open‐ended stubs and half‐wavelength short‐ended stubs are respectively exploited in the proposed dual‐band power‐divider configurations to incorporate the dual‐band functionality into them for flexibly‐adjustable dual‐frequency‐ratio specifications. Each engineered five‐port power‐divider circuit features high in‐band input/output power‐matching levels, high in‐band power‐isolation levels between the two differential‐mode outputs, and high common‐mode‐rejection levels in a broad spectral range. Two microstrip prototypes designed at 0.9/1.8 GHz (GSM bands) and 1.57/2.45 GHz (GPS and WLAN bands) are constructed and characterized for experimental‐demonstration purposes. [ABSTRACT FROM AUTHOR]

In this article, four wideband power dividers (two are filtering power dividers) using single‐ and double‐layer periodic spoof surface plasmon polaritons (SSPPs) are proposed. Double‐sided parallel‐strip line is used to realize the wideband and low loss for the double‐layer SSPPs. T‐shaped SSPPs power dividers with large bandwidth, wideband isolation, and low loss using double‐layer SSPPs to single‐layer SSPPs transition are realized. Conventional coplanar waveguide is used as the output ports for the single‐layer SSPPs. Moreover, two new SSPPs power dividers with filtering performance are realized with adding via holes in the double‐layer SSPPs. The theoretical analysis, parametric study, and design procedure for these wideband power dividers are illustrated. In addition, for validity demonstration, four wideband SSPPs power dividers are fabricated in microstrip technology and characterized. Good agreements can be observed between the measured and simulated results, indicating good potential applications in the integrated plasmonic devices. [ABSTRACT FROM AUTHOR]