Search

Anatomical/physiological gastrointestinal changes after bariatric surgery may influence the fate of orally administered drugs.Since non-selective NSAIDs are not well-tolerated post-surgery, selective cyclooxygenase-2 (COX-2) inhibitors may be important for these patients. In this work we investigated celecoxib, etoricoxib and etodolac, for impaired post-bariatric solubility/dissolution and absorption. Solubility was studied in-vitro, and ex-vivoin aspirated gastric contents from patients pre- vs. post-surgery. Dissolution was studied in conditions simulating pre- vs. post-surgery stomach. Finally, the experimental solubility data were used in physiologically-based biopharmaceutics model (PBBM) (GastroPlus®) to simulate pre- vs. post-surgery celecoxib/etoricoxib/etodolac pharmacokinetic (PK) profiles.For etoricoxib and etodolac (but not celecoxib), pH-dependent solubility was demonstrated: etoricoxib solubility decreased ∼1000-fold, and etodolac solubility increased 120-fold, as pH increased from 1 to 7, which was also confirmed ex-vivo. Hampered etoricoxib dissolution and improved etodolac dissolution post-surgery was revealed. Tablet crushing, clinically recommended after surgery, failed to improve post-bariatric dissolution. PBBM simulations revealed significantly impaired etoricoxib absorption post-surgery across all conditions; for instance, 79% lower C max and 53% decreased AUC was simulated post-gastric bypass procedure, after single 120 mg dose. Celecoxib and etodolac maintained unaffected absorption after bariatric surgery.This mechanistically-based analysis suggests to prefer the acidic drug etodolac or the neutral celecoxib as selective COX-2 inhibitors, over the basic drug etoricoxib, after bariatric surgery., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

The objective of this study was to formulate extended-release mucoadhesive buccal tablets of propranolol hydrochloride in order to provide a prolonged absorption of propranolol hydrochloride from the buccal mucosa and to reduce presystemic metabolism and thus provide a better therapeutic effect. Besides, the aim was to perform comparative in vivo pharmacokinetic and hemodynamic studies of the developed extended-release (ER) propranolol hydrochloride 10 mg mucoadhesive buccal tablets and commercial immediate-release (IR) propranolol hydrochloride 10 mg tablets in spontaneously hypertensive rats. Formulation with 15% polyethylene oxide showed the highest degree of propranolol hydrochloride permeation, satisfactory mucoadhesiveness, and extended-release of propranolol hydrochloride, thus it was selected for further in vivo study. The pharmacokinetic study in rats showed the superiority of ER mucoadhesive buccal tablets over IR tablets in terms of propranolol hydrochloride absorption extent (AUC values: 70.32 ± 19.56 versus 31.69 ± 6.97 µg·h/mL), although lower maximum plasma propranolol hydrochloride concentration (C max ) was achieved. However, no statistically significant difference was observed in C max between these treatments. The hemodynamic study showed that ER mucoadhesive buccal tablets provide a more pronounced decrease primarily in heart rate, but also in systolic and diastolic arterial pressure, as well as a longer heart rate reduction compared to IR tablets., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Paracetamol-loaded tablets were printed by fused deposition modelling technique, using polyvinyl alcohol as a backbone polymer and Affinisol™ HPMC as a plasticizer in all formulations. Four different strategies were applied in order to accelerate the drug release from the tablets. First, different release enhancers were added: sodium starch glycolate, croscarmellose sodium, Kollidon CL and mannitol. Kollidon CL and mannitol showed the greatest influence on the drug dissolution rate. The second strategy included lowering the infill density, which did not make any significant changes in dissolution profiles, according to the calculated similarity factor. Then the best two release enhancers from the first strategy were combined (Kollidon CL and mannitol) and this proved to be the most effective in the drug release acceleration. The fourth strategy, increasing the percentage of the release enhancers in formulation, revealed the importance of their concentration limits. In summary, the drug release accelerated from 58% released after 5 h to reaching the plateau within 2 h. In silico physiologically-based biopharmaceutics modelling showed that formulations with mannitol and Kollidon CL, especially the formulation containing a combination of these release enhancers, can provide relatively fast drug release and extent of drug absorption that complies with an immediate release tablet., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Paracetamol printlets were prepared via hot-melt extrusion process and fused deposition modelling, using two types of backbone polymers. Polycaprolactone (PCL) and Polyethylene oxides (PEO) 100 K and 200 K were used, while Arabic gum was used as a plasticizer to facilitate the material flow and Gelucire® 44/14 as an enhancer of drug release. Different drug/polymer ratios were prepared. Extrusion temperature was adjusted according to the mixture/polymer types. It was possible to produce filaments with maximum of 60% w/w of drug. Mechanical properties of filaments were evaluated using three-point bend test, while obtained parameters were modelled using decision tree as a data mining method. Correlation between maximum displacement, maximum force and printability was obtained with accuracy of 84.85% and can be a useful tool for predicting printability of filaments. This study briefly demonstrated that backbone polymer in formulation plays crucial role in obtaining FDM printlets with desired properties. PEO-based filaments were more prone to be clogged in printcore, but their printlets showed much faster drug release. Drug release from all printlets was prolonged: from 50% in 8 h (PCL), to complete release in 4 h (PEO). Paracetamol release kinetics was guided by anomalous transport, attributed to the diffusion and erosion process., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Three-dimensional (3D) printing enables the production of different objects adjusted for the specific application, which has particular importance of providing personalized therapy, whereby the challenge is to apply pharmaceutical materials into 3D printing technology. In this study, effect of poly(ethylene glycol) 400 (PEG 400), sodium chloride (NaCl), and mannitol, as hydrophilic excipients, was investigated in order to overcome very slow and incomplete drug release from tablets (printlets) fabricated by photopolymerization using digital light processing (DLP) technology. Paracetamol (acetaminophen) was used as a model drug, while polyethylene glycol diacrylate (PEGDA) was used as a photopolymer and diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide as a photoinitiator in photoreactive mixtures. Most of printlet formulations exhibit sustained release over 8 h, wherein drug release kinetics is the best described with Korsmeyer-Peppas kinetics. Variation in the content of photopolymer and excipients had an influence on the dissolution rate, mechanical characteristics, and internal structure of the investigated samples. The addition of hydrophilic polymers increased drug release rate, while PEGDA had the greatest influence on the tensile strength of printlets. The results indicate the possibility of implementation of traditional excipients into different formulations for photopolymerization based 3D printing for the production of small batches of tablets with tailored drug release., (Copyright © 2019 Elsevier B.V. All rights reserved.)