Search

Abstract: Direct carbon fuel cells are promising power sources using solid carbon directly as fuel. Their performances significantly depend on the electrooxidation activity of carbon fuel. Electrooxidation of activated carbon particulates in molten Li2CO3–K2CO3 was investigated by potentiodynamic and potentiostatic method. Results indicated that the electrooxidation performance of activated carbon was significantly enhanced by pre-soaking with Li2CO3–K2CO3 and by treatment with HF, HNO3 and NaOH, respectively. The onset potential negatively shifted by around 100 mV and the current density increased by around 50 mA cm−2 after pre-soaking. The non-oxidant acids (HF) treatments are more effective than oxidant acid (HNO3) and base (NaOH) treatments. HF treated activated carbon exhibited the highest activity among all the samples. The enhancement in electrooxidation performance can be closely correlated with the increase in surface area and porosity caused by acid and base treatments. [Copyright &y& Elsevier]

A binder-free and flexible Au electrode is prepared by spontaneous deposition of Au onto a A4 (A4-paper)-8B (8B pencil)-Ni Film substrate (ABNi) which is assembled by electrodeposition of nanoscale Ni particles on the surface of A4 paper coated by 8B pencil. The morphology and phase structure of the (A4-paper)-8B (8B pencil)-Ni Film-Au (ABNiAu) electrode are characterized by scanning electron microscopy equipped with energy dispersive X-ray spectrometer and X-ray diffractometer. The catalytic activity of the ABNiAu electrode for NaBH 4 electrooxidation is investigated by means of cyclic voltammetry and chronoamperometry. The electrode exhibits a high electric conductivity and the activity substance attaches to the surface of paper substrate tightly and does not fall off at all and the nanoscale Ni and Ni Au alloy enhance the broken of the B H bond in the BH 4 − , all of which lead to a high catalytic activity for NaBH 4 electrooxidation. The oxidation current density reaches 300 mA cm −2 in 1 mol dm −3 NaOH and 0.1 mol dm −3 NaBH 4 at −0.2 V. The exchanged electrons (n) is 6.0 (8.0 in theory), which indicates that the ABNiAu electrode has much higher utilization efficiency of the fuel than our reported LaNi 5 /Pd (n = 4) electrode. [ABSTRACT FROM AUTHOR]

Recently, direct borohydride fuel cell (DBFC) has been considering as a promising energy conversion devices. During the development of DBFC, reducing the use of noble metals and increasing the anode performance are the hot topic in recent researches. In this article, reduced graphene oxide nanosheets deposit on C@TiC coaxial nanowire array (rGO-C@TiC) by means of a combine method of chemical vapor deposition and electrodeposition is chosen as 3D current collector for Pd nanoparticles deposition. The morphology and crystal structure of the as-obtained 3D electrode is checked with FESEM, TEM, EDS, and XRD. Results claim that the as-prepared 3D electrode exhibits a mushroom-like structure with the mean diameter size of Pd is 5.32 nm. Their catalytic ability for NaBH 4 electro-oxidation is evaluated in a three electrode system by using the method of cycle voltammetry and chronoamperometry, proving that the 3D Pd-rGO-C@TiC electrode has a higher catalytic performance. The oxidation current density of 1.35 A cm −2 mg −1 Pd is achieved at −0.6 V. Furthermore, a direct borohydride-hydrogen peroxide fuel cell (DBHPFC) is assembled by using the as-prepared Pd-rGO-C@TiC electrode and a Pd/CFC electrode as anode and cathode catalyst, respectively, and a maximum power density of 68.5 mW cm −2 is obtained. In addition, the assembled DBHPFC shows excellent higher performance based on the mass activity basis (1427.1 W g −1 ) among those reported literatures, indicating that our Pd-rGO-C@TiC could be acted as a promising cost-effective and ponderable alternative catalyst for NaBH 4 electrooxidation. [ABSTRACT FROM AUTHOR]

Three-dimensional (3D) reduced graphene networks (RGN) were successfully fabricated on Ni foam without any conductive agents and polymer binders by dipping commercial Ni foam into graphene oxide (GO) suspension and subsequent a electroreduction process in a buffer solution. Au nanoparticles were then deposited on the RGN through an electrodeposition process to form a novel reduced graphene networks-Au (RGNA) electrode. The morphology and phase structure of the RGNA electrode are characterized by scanning electron microscope, transmission electron microscope and X-ray diffraction spectrometer. The NaBH 4 electrooxidation performance on the RGNA electrode is investigated by means of cyclic voltammetry and chronoamperometry. The RGNA electrode owns special hierarchical porous structure, rapid electron and ion transport, and large electroactive surface area due to the intrinsic electronic conductivity, mesoporous nature of graphene. The RGNA electrode exhibits a good stability during the electrochemical process and the oxidation current density at RGNA electrode reached 500 mA cm −2 at 0 V in the solution containing 0.1 mol dm −3 NaBH 4 and 2 mol dm −3 NaOH, which is higher than that at bare Au–Ni foam without graphene. The excellent structural stability and high catalytic performance for NaBH 4 electrooxidation make the RGNA a promising material for future energy systems. [ABSTRACT FROM AUTHOR]

Abstract: Flexible and wearable cobalt electrode with a unique three-dimensional hierarchical-network structure is prepared by electrodeposition of spherical Co particles onto multiwalled carbon nanotubes (MWNTs) which are assembled on the skeleton of cosmetic cotton (CC). The morphology and phase structure of the cobalt–multiwalled carbon nanotubes–cosmetic cotton (Co–MWNTs–CC) electrode are characterized by scanning electron microscope, transmission electron microscope and X-ray diffraction spectrometer. The NaBH4 electrooxidation performance on the Co–MWNTs–CC electrode is investigated by means of cyclic voltammetry and chronoamperometry. Results show that the Co–MWNTs–CC electrode exhibits remarkably high catalytic activity and good stability for NaBH4 electrooxidation. The oxidation current density reaches as high as 170 mA cm−2 at −0.7 V in 1.0 mol dm−3 NaOH and 0.1 mol dm−3 NaBH4, which is higher than the most-related previous results. [Copyright &y& Elsevier]