Search

In this work, shellac and its crosslinking were studied to produce paper straws for the application of liquid products. Commercial paper straws are not durable for liquid foods due to their hygroscopic nature, and thus, they find it challenging to replace single-use plastics. Shellac is a naturally occurring resin utilized as an adhesive and water-resistant coating over the paper straw. Shellac was cured at 125 °C, 150 °C, 175 °C, and 200 °C, and it was crosslinked in about 210 min, 150 min, 60 min, and 30 min respectively and studied for kinetics. The crosslinking of shellac produced a thermally stable material. Compared to commercial paper straws, these paper shellac straws exhibited high bending stiffness (1356.11 Nmm), tensile strength (13,74 MPa), flexural strength (21.72 MPa), and compression strength (24.99 MPa). Moreover, the paper shellac straws didn't bend in wet conditions under load for up to one day, while the commercial paper straw bends in 8 min. Therefore, paper straws with shellac can replace plastic-based straws for a sustainable future., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Arihant Ahuja reports financial support was provided by the Prime Minister Research Fellowship, Ministry of Education, India. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The work was aimed at evaluating the adsorptive properties of waste newspaper (WN) activated carbons chemically produced using sodium salts for methylene blue (MB) and congo red (CR) removal. The activated carbons, designated as AC1, AC2, AC3 and AC4 were prepared through impregnation with NaH 2 PO 4 , Na 2 CO 3 , NaCl and NaOH, respectively and activation at 500 °C for 1 h. The activated carbons were characterized for surface chemistry, thermal stability, specific area, morphology and composition. The AC1 with a surface area of 917 m 2 /g exhibits a greater MB capacity of 651 mg/g. Meanwhile, a greater CR capacity was recorded by AC2 at 299 mg/g. The pseudo-second order model fitted well with the kinetic data, while the equilibrium data could be described by Langmuir model. The thermodynamic parameters, i.e.., positive ΔH°, negative ΔG° and positive ΔS° suggest that the adsorption of dyes is endothermic, spontaneous and feasible at high solution temperature. To conclude, WN is a potential cellulose source for producing activated carbon, while NaH 2 PO 4 activation could be employed to convert WN into activated carbon for effective dye wastewater treatment., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The growing interest in paper-based materials for packaging is driven by their renewable and eco-friendly characteristics. However, their poor barrier performance against water, oil, and gas limits their application in the food packaging industry. In this study, we developed a simple dual-layer coating method to create water- and oil-repellent, gas barrier, antioxidant, and antibacterial paper-based materials using naturally-derived materials, including chitosan (CS), ethyl cellulose (EC), and cascade biorefinery products from green walnut husk (GWHE and CNC). The bottom CS/CNC oil-resistant coating and the top EC/GWHE water-resistant coating were applied to the paper surface. The synergistic effect of these coatings enhances the gas barrier and imparts functional properties to the paper. Compared to uncoated paper, the dual-layer-coated paper demonstrated a 239.1 % increase in tensile index, a higher kit rating value of 12/12, a lower Cobb 60 value of 3.21 mg/m 2 , a 44.0 % decrease in water vapor permeability (WVP), and a 90.7 % reduction in air permeability (AP). Additionally, this coated paper exhibited good antioxidant and antibacterial properties and favorable biodegradability. This study provides novel insights into the valorization of GWH waste and presents a sustainable strategy for producing high-performance paper-based materials for food packaging applications., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

This study developed a multifunctional paper-based freshness antibacterial indicator card by dual-sided coating on conventional filter paper. The indicator coating was composed of anthocyanins from purple cabbage, and polyvinyl alcohol and sodium carboxymethyl cellulose as substrates while the antibacterial coating contained halloysite nanotubes for loaded thyme essential oil and chitosan. FT-IR, XRD, and SEM analyses revealed that the components were well-mixed, and the paper was tightly bound to the coatings through hydrogen bonds. Additionally, the coating effectively filled the porous fiber gaps in the paper, significantly enhancing the mechanical properties of the paper. The tensile strength of the coated paper was enhanced from 14.28 MPa to a range of 42.25-47.71 MPa, and the bending resistance was increased from 0.35 N·mm to a range of 1.72-1.99 N·mm compared to the uncoated paper. The addition of anthocyanins provided excellent sensitivity to pH and ammonia for the indicator card. Furthermore, the coating including halloysite nanotubes for loaded thyme essential oil exhibited antimicrobial resistance against Escherichia coli and Staphylococcus aureus. When used on fresh carp, the antibacterial indicator card not only indicated the freshness of the carp but also extended the best before date of the fish meat by 1-2 days. The indicator exhibited the most pronounced color transformation and optimal freshness indication performance when the mass fraction of anthocyanins was 2 %., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. This work is original research and the data presented in the manuscript has not been published elsewhere., (Copyright © 2024 Elsevier B.V. All rights reserved.)

MOF-199 is considered to be an excellent CO 2 adsorbent owing to its substantial specific surface area, suitable pore structure and abundant sorption sites. However, powdered MOF-199 is prone to agglomeration and has poor recyclability. Herein, we proposed a MOF-199-based adsorbent by combining the MOF synthesis process with traditional papermaking process. Through such a design, MOF-199 particles are adhered on the surface of wood pulp fiber. The sufficient hydroxyl groups and electrostatic forces of cellulose facilitates the homogeneous and tight adhesion of MOF crystals. The optimal MP-4 sample demonstrated a high CO 2 adsorption capacity (1.80 mmol·g --1 at 25 °C) and good CO 2 /N 2 selectivity (30.06). Moreover, the composite sorbent can be easily regenerated. The adsorption mechanism was analyzed by the density functional theory approach. The simulation results showed that the carboxyl functional groups with a large number of oxygen atoms and active metal sites are the key to boost the CO 2 adsorption performance., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Cellulose fibers(CFs)-based electrode materials are of considerable interest for future wearable electronic devices due to excellent flexibility and strength, and hydrophilicity. The effective introduction of electrode materials into CFs is essential for flexible supercapaciotors(SCs). A tunable electrochemical performance of conductive polymers for poly(3,4-ethylenedioxythiophene)(PEDOT) has been aroused great interests. Herein, we design its electrochemical process via sodium anthraquinone-2-sulfonate(AQS) as dopant and electrolyte additive to construct active electrode interior and interface. As a result, the PEDOT@CFs electrode exhibits great increase of doping level from 0.16 to 0.29, conductivity from 353.46 to 626.15 S m -1 , and specific capacitance from 140.22 to 1211.57 F g -1 at a current density of 0.2 A g -1 . Furthermore, the PEDOT:AQS@CFs electrode possess excellent cyclic stability (96.01 %) after 1000 cycles. The work reveals the mechanism of AQS as dopant and electrolyte additive, and provides a new perspective for application of PEDOT in energy storage field., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

In order to reduce the quality loss of citrus and extend its storage time after harvest, it is essential to develop coated kraft papers with antibacterial and fresh-keeping properties. In this study, cinnamon essential oil (CEO)/soybean protein isolate (SPI) microcapsules were prepared by the coagulation method, and their properties were optimized. Then, the microcapsules were added to konjac glucomannan (KGM) as a coating solution to enhance the physical, and chemical properties of kraft paper by a coating method. The release behavior of CEO, tensile properties, antibacterial properties and preservation effects of the paper were investigated. The results show that when the ratio of wall to core was 7:3, the highest encapsulation rate was 92.20 ± 0.43 %. The coating treatment significantly reduced the oxygen and water vapor transmission rates of kraft paper. The shelf life of citrus treated with coated Kraft was extended by >10 days. Thus, the CEO/SPI microencapsulation and KGM coating could improve the properties of kraft paper and have the potential for citrus preservation., Competing Interests: Declaration of competing interest We declare that this manuscript as original and there are not any financial or other conflicts of interests. As the corresponding author, I confirmed that the manuscript has been read and approved for submission by all named authors who have contributed significantly., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Due to intrinsic defect of fire hazard security, improving the flame retardant capacity of paper is still insufficient in case of precombustion. Herein, we integrate the flame retardant with flame detection performance on the surface of paper, the restricts of graphene oxide (GO) are overcome between high thermoelectric performance and flexibility. A flexible lamellar thermoelectric composite (GO-LA-HP) is constructed through the co-assembly of GO, ascorbic acid (LA), and phenoxycycloposphazene (HP), lamellar GO-LA-HP avoid GO's toughness decline after modification, but also enhance fire sensitivity and flame resistance. The composite could significantly decrease the temperature rise stage (<150 °C), and trigger the fire-warning within 2 s. The hybrid coating composed of phytic acid/phosphoric acid (PyA/PA) and modified thermoelectric GO-LA-HP becomes excellent compatibility on the surface of the modified paper (GPP). GPP is able to extinguish itself immediately after leaving the fire in the vertical combustion, and display the excellent flame resistance. Furthermore, GPP's alarm signal could be timely generated as little as 3 s of contacting the flame, and the response time can exceed 600 s. According to the structure observation and analysis, the related synergistic fire detection reinforcing and flame-retardant mechanisms are also proposed and clarified., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

To optimize the imbalance between the interfacial bonding and porosity properties of carbon paper (CP) caused by phenol formaldehyde resin (PF) impregnation, and therefore improve the performance of proton exchange membrane fuel cells (PEMFCs), a new approach through cellulose nanofibers grafted with methyl methacrylate (CNFM) as a modified reinforcement and pore-forming agent for PF is investigated. Through suppressing the methylene backbone fracture of CNFM-modified PF during its thermal depolymerization, the interfacial bonding between PF matrix carbon and carbon fibers is enhanced. Compared with unmodified CP, the in-plane resistivity of CNFM-modified CP is reduced by 35.78 %, while the connected porosity increases to 82.26 %, and more homogeneous pore size distribution (PSD) in the range of 20-40 μm is obtained for CNFM-modified CP. Besides, the tensile strength, flexural strength, and air permeability of CNFM-modified CP increase by 72.78 %, 298.4 %, and 103.97 %, respectively. In addition, CNFM-modified CP achieves the peak power density of PEMFCs to 701.81 mW·cm -2 , exhibiting 10.98 % improvement compared with commercial CP (632.39 mW·cm -2 ), evidently achieving an integral promotion of CP and comprehensive performance., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

Electromagnetic hydrogels have attracted significant attention due to their vast potential in soft robotics, biomedical engineering, and energy harvesting. To facilitate future commercialization via large-scale industrial processes, we present a facile concept that utilizes the specialized knowledge of papermaking to fabricate hydrogels with multifunctional electromagnetic properties. The principles of papermaking wet end chemistry, which involves the handling of interactions among cellulosic fibers, fines, polymeric additives, and other components in aqueous systems, serves as a key foundation for this concept. Notably, based on these principles, the versatile use of chemical additives in combination with cellulosic materials enables the tailored design of various products. Our methodology exploits the unique hierarchically pitted and hollow tube-like structures of papermaking grade cellulosic fibers with discernible pits, enabling the incorporation of magnetite nanoparticles through lumen loading. By combining microscale softwood-derived cellulosic fibers with additives, we achieve dynamic covalent interactions that transform the cellulosic fiber slurry into an impressive hydrogel. The cellulosic fibers act as a skeleton, providing structural support within the hydrogel framework and facilitating the dispersion of nanoparticles. In accordance with our concept, the typical hydrogel exhibits combined attributes, including electrical conductivity, self-healing properties, pH responsiveness, and dynamic rheologic behavior. Our approach not only yields hydrogels with interesting properties but also aligns with the forefront of advanced cellulosic material applications. These materials hold the promise in remote strain sensing devices, electromagnetic navigation systems, contactless toys, and flexible electronic devices. The concept and findings of the current work may shed light on materials innovation based on traditional pulp and paper processes. Furthermore, the facile processes involved in hydrogel formation can serve as valuable tools for chemistry and materials education, providing easy demonstrations of principles for university students at different levels., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

The monitoring of foodborne bacterial contamination requires simple and convenient biosensors. This work describes a novel paper-based colorimetric biosensor for the rapid and sensitive bacteria detection. The biosensor was constructed via the encapsulation of D-alanyl-D-alanine capped gold nanoparticles (DADA-AuNPs) in a modified paper that was fabricated by the freeze-drying of TEMPO-oxidized cellulose nanofibers/cationic guar gum composite hydrogel-modified filter paper. The results indicated that the size of DADA-AuNPs largely determined the color of their aqueous system and they exhibited light red to dark red as their size increased from around 6 to 36 nm. All these different sized DADA-AuNPs turned into colorless when encountered with either S. aureus or E. coli. In particular, the smaller the DADA-AuNPs size, the faster the discoloration. The encapsulation of DADA-AuNPs into modified paper negligibly changed their responsiveness towards bacteria. In comparison to the original filter paper and oven-dried hydrogel-modified filter paper, the freeze-dried hydrogel-modified paper was demonstrated to be a better substrate for the encapsulation of DADA-AuNPs since they could be loaded with a larger amount of DADA-AuNPs in a faster way and showed a better perceivable color. This work demonstrated a promising paper-based colorimetric biosensor for the facile and rapid detection of bacteria., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The aging of paper seriously threatens the service life of cultural heritage documents. Bacterial cellulose (BC), which has a good fiber aspect ratio and is rich in hydroxyl groups, is suitable for strengthening aged paper. However, a single BC added was not ideal for paper restoration, since only strengthening was not able to resist the persistent acidification of ancient book. In this work, BC was functionalized by 3-aminopropyltriethoxysilane (APTES) to develop the interface bonding with aged paper. Fourier transform infrared (FTIR), X-ray diffraction (XRD), nuclear magnetic resonance (NMR) and elemental analysis identified the successful amino-silanization of BC. The modification parameters were optimized as the concentration of APTES of 5 wt%, the reaction time of 4 h, and the reaction temperature of 80 °C based on a considerable improvement in the strength properties without obvious appearance impact on reinforced papers. Moreover, the pH value of the repaired paper was achieved at 8.03, ensuring the stability of the anti-aging effect. The results confirmed that APTES-BC had great potential applications in ancient books conservation., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. All the authors listed have approved the manuscript enclosed., (Copyright © 2024. Published by Elsevier B.V.)

Developing plastic/fluorine/silicon-free and degradable water/oil-resistant coatings for paper-based packaging materials to replace disposable plastic products is a very effective way to solve the problem of 'white pollution' or microplastics pollution. A novel water/oil-resistant coating was developed by alkyl ketene dimer (AKD)-based Pickering emulsion and chitosan in this work. Cellulose nanofibrils (CNF) were used as a stabilizing solid for AKD emulsion, with the addition of chitosan as an oil-resistance agent. The coating provides excellent hydrophobicity, water/oil resistance as well as good barrier properties. The water contact angle was as high as 130° and the minimum Cobb60 value was 5.7 g/m 2 , which was attributed to the hydrophobicity of AKD. In addition, the kit rating reached maximum 12/12 at coating weight of 8.26 g/m 2 and the water vapor transmittance rate (WVTR) was reduced to 153.4 g/(m 2 ⋅day) at the coating weight of 10.50 g/m 2 . The tensile strength of the paper was increased from 28.1 to 43.6 MPa after coating. Overall, this coating can effectively improve the performance of paper-based materials, which may play an important role in the process of replacing disposable plastic packaging with paper-based materials., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Paper-based test film material is widely used in a variety of test instruments for different applications. The enzyme activity test paper sheet is one of the most popularly used test papers. Here we present a novel fabrication of paper-based enzyme activity test paper without cationic resin added in. The chemical pulping fibers were first beaten to different degrees (from 14.6 to 41.5°SR) with a PFI beater. After that, the fibers were modified with a cationic agent (3-chloro-2-hydroxypropyl trimethyl ammonium chloride) under the system of alkali and water solution. Finally, the test papers were made with the modified fiber by a regular paper former in lab. The results showed that beating is beneficial for the improvement of the cationization reaction which is indicated by the Zeta potential, FTIR and EDS. The main mechanisms involved are the destruction of crystalline zone, increase of free hydroxyl group and defibrillation. This hypothesis was supported by the SEM, XRD and fiber analyzer. Beating under the optimized condition, the wet strength and liquid absorbability of test paper can meet the application requirement, and the test results of enzyme activity are quite close to those of commercial test papers., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

In recent years, researchers have put much attention on the improvements and upgrades of novel wet strength agent in the papermaking fields, especially in the usage of household paper. Herein, PEI M -KH560 by polyethyleneimine (PEI) and γ-glycidyl ether propyl trimethoxysilane (KH560) was synthesized with five molecular weights (Mw) of PEI at 600, 1800, 10,000, 70,000 and 750,000. Results showed that the molecular weight greatly influenced the physicochemical properties of PEI-KH560, such as the size and thermal stability. The intrinsic cationic charge of PEI-KH560 provided the bonding sites with the paper fibers, forming strengthened fiber-fiber joints. It was shown that the dry, wet strength and hydrophobicity of cellulosic paper sheets were obviously improved. When the m (PEI):m(KH560) is 1:2, the strength of papers after sizing by Mw of PEI at 600 and 1800 is the most obvious, with the dry strength increased by 227.9 % and 187.5 %, and the wet strength increased by 183.8 % and 207.8 %, respectively. The maximum hydrophobicity was found at the PEI 1800 -KH560 with the contact angle value of 130.6°. The resultant environmental-friendly agent (PEI-KH560) obtained in this work provides valuable significance for the preparation of household and food packaging paper., Competing Interests: Declaration of competing interest The authors declare that they have no known competing interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

This study focuses on enhancing the strength and water stability of paper straws through a novel approach involving a binary emulsion of lignin-based polyurethane and chitosan. Kraft lignin serves as the raw material for synthesizing a blocked waterborne polyurethane, subsequently combined with carboxylated chitosan to form a stable binary emulsion. The resulting emulsion, exhibiting remarkable stability over at least 6 months, is applied to the base paper. Following emulsion application, the paper undergoes torrefaction at 155 °C. This process deblocks isocyanate groups, enabling their reaction with hydroxyl groups on chitosan and fibers, ultimately forming ester bonds. This reaction significantly improves the mechanical strength and hydrophobicity of paper straws. The composite paper straws demonstrate exceptional mechanical properties, including a tensile strength of 47.21 MPa, Young's modulus of 4.33 GPa, and flexural strength of 32.38 MPa. Notably, its water stability is greatly enhanced, with a wet tensile strength of 40.66 MPa, surpassing commercial paper straws by 8 folds. Furthermore, the composite straw achieves complete biodegradability within 120 days, outperforming conventional paper straws in terms of environmental impact. This innovative solution presents a promising and sustainable alternative to plastic straws, addressing the urgent need for eco-friendly products., Competing Interests: Declaration of competing interest There are no conflicts to declare., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Counterfeiting has caused great concern all over the world. What's more, the fluorescent materials play an important role in technological research and development for high-security. In this work, lead-metal-organic framework (Pb-MOF) and perovskite (MAPbBr 3 ) were used in papers to achieving fluorescence counterfeiting. Pb-MOF, as the template or precursor of MAPbBr 3 , were in-situ generated on the surface of cellulose fibers (CFs) to preparing into hand sheets (Pb-MOF@CFs). Through the analysis of experimental results, it was found that ligands, reaction systems, addition sequences of drugs, time, etc. would affect the deposition of Pb-MOF on the surface of CFs. Using CH 3 NH 3 Br (MABr) as the anti-counterfeiting ink to write on Pb-MOF@CFs, the orange writing leaped across the paper, which caused by Pb in Pb-MOF chemically reacting with MABr forming MAPbBr 3 . The orange writing displayed green fluorescence under 365 nm ultraviolet lamp excitation. The orange writing with green fluorescence could be extinguished and reconstructed, which had promise for reuse. In addition, fluorescent security papers (MAPbBr 3 @Pb-MOFs@CFs) were prepared by immersing Pb-MOF@CFs in MABr solution. The fluorescence of MAPbBr 3 @Pb-MOFs@CFs opened when the surface of it was scraped under 365 nm ultraviolet lamp. This unique fluorescence property was very important in improving the security of products. Consequently, the ongoing research on perovskite and MOFs materials is of great significance., Competing Interests: Declaration of competing interest We declare that we have no financial and personal relationships with other people or organizations that can inappropriately influence our work, there is no professional or other personal interest of any nature or kind in any product, service and/or company that could be construed as influencing the position presented in, or the review of, the manuscript entitled., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The abnormal uric acid (UA) level in urine can serve as warning signals of many diseases, such as gout and metabolic cardiovascular diseases. The current methods for detecting UA face limitations of instrument dependence and the requirement for non-invasiveness, making it challenging to fulfill the need for home-based application. In this study, we designed an aptasensor that combined UA-specific transcriptional regulation and a fluorescent RNA aptamer for convenient urinary UA testing. The concentration of UA can be translated into the intensity of fluorescent signals. The aptasensor showed higher sensitivity and more robust anti-interference performance. UA levels in the urine of different volunteers could be accurately tested using this method. In addition, a paper-based aptasensor for UA self-testing was manufactured, in which the urinary UA levels could be determined using a smartphone-based colorimetric approach. This work not only demonstrates a new approach for the design of disease-associated aptasensor, but also offers promising ideas for home-based detection of UA., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The demand for paper-based packaging materials as an alternative to incumbent disposable petroleum-derived polymers for food packaging applications is ever-growing. However, typical paper-based formats are not suitable for use in unconventional applications due to inherent limitations (e.g., excessive hydrophilicity, lack antimicrobial ability), and accordingly, enabling new capabilities is necessity. Herein, a simple and environmentally friendly strategy was proposed to introduce antimicrobial and hydrophobic functions to cellulose paper through successive chemical grafting of 3-aminopropyltriethoxysilane (APS) and cinnamaldehyde (CA). The results revealed that cellulose paper not only showed long-term antibacterial effect on different bacteria, but also inhibited a wide range of fungi. Encouragingly, the modified paper, which is fluorine-free, displays a high contact angle of 119.7°. Thus, even in the wet state, the modified paper can still maintain good mechanical strength. Meanwhile, the multifunctional composite papers have excellent biocompatibility and biodegradability. Compared with ordinary cellulose paper, multifunctional composite paper can effectively prolong the shelf life of strawberries. Therefore, the multifunctional composite paper represents good application potential as a fruit packaging material., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Sustainable strategies to improve the water resistance of cellulose paper are actively sought. In this work, polymeric microspheres (PMs), prepared through emulsion polymerization of cellulose nanofibers stabilized rubber seed oil-derived monomer, were investigated as coatings on corrugated medium paper (CMP). After infiltrating porous paper with PMs, the water-resistant corrugated papers (WRCP n ) with enhanced mechanical properties were obtained. When 30 wt% PMs were introduced, WRCP 30 turned out to be highly compacted with an increased water contact angle of 106.3° and a low water vapor transmission rate of 81 g/(m 2 d) at 23 °C. Meanwhile, the tensile strength of WRCP 30 increased to 22.2 MPa, a 4-fold increase from CMP. When tested in a well-hydrated state, 71% of its mechanical strength in the dry state was maintained. Even with a low content of 10 wt% PMs, WRCP 10 also exhibited stable tensile strength and water wettability during the cyclic soaking-drying process. Thus, the plant oil based sustainable emulsion polymers provide a convenient route for enhancing the overall performance of cellulose paper., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Frequent oceanic oil spill incidents and the discharge of industrial oily wastewaters have caused serious threats to environments, food chains and human beings. Lignin wastes with many reactive groups exist as the byproducts from bioethanol and pulping processing industries, and they are either discarded as wastes or directly consumed as a fuel. To make full use of lignin wastes and simultaneously deal with oily wastewaters, porous lignin-based composites have been rationally designed and prepared. In this review, recent advances in the preparation of porous lignin-based composites are summarized in terms of aerogels, sponges, foams, papers, and membranes, respectively. Then, the mechanisms and the application of porous lignin-based adsorbents and filtration materials for oil/water separation are discussed. Finally, the challenges and perspectives of porous lignin-based composites are proposed in the field of oil/water separation. The utilization of abundant lignin wastes can replace fossil resources, and meanwhile porous lignin-based composites can be used to efficiently treat with oily wastewaters. The above utilization strategy opens an avenue to the rational design and preparation of lignin wastes with high-added value, and gives a possible solution to use lignin wastes in a sustainable and environmentally friendly way. [ABSTRACT FROM AUTHOR]