Search

In low-frequency vibration-assisted drilling (LFVAD) of CFRP/Ti6Al4V stacks, owing to the different mechanical and thermal performances of the involved carbon fiber–reinforced plastic (CFRP) composite and Ti6Al4V alloy, the short tool life of commonly used carbide (WC) tools and rapidly deteriorated machining quality are the major problems. This paper aims to explore whether the polycrystalline diamond (PCD) tool can achieve a competitive effect on drilling CFRP/Ti6Al4V stacks compared with previous CFRP drilling studies. To avoid the frequent occurrence of chisel edge fracture in LFVAD of Ti6Al4V alloy, a model of plowing behavior is established and parametric experiments based on it are performed with both PCD and WC drills. It is found that the periodically dynamic force is the major factor causing the chisel edge fracture of the PCD drill, which can be alleviated by reducing the feed rate. Besides, by using PCD drills instead of WC drills in Ti6Al4V drilling, the exit burr height, drilling diameter deviation, and surface roughness value are reduced under each given parameter. Finally, PCD and WC drill bits are used to perform a wear test on the CFRP/Ti6Al4Vstacks under optimized parameters. The PCD drill achieves superior performance, including lower wear rate, better hole quality, and higher consistency. The experiments discussed in this paper provide some suggestions for selecting tools and cutting parameters when drilling CFRP/Ti6Al4V stacks. [ABSTRACT FROM AUTHOR]

Machining of CFRP composites is usually described as a challenging process from tool life and surface quality perspectives. To achieve a flawless machined surface at reasonable cutting tool life/cost, an optimum combination of cutting tool material and geometry is the key. The cutting tool angles are of importance as these dictate the cutting mechanism as well as the cutting edge robustness and the introduction of vibration to the machining process opens up new horizons of improvement and stirs further research questions. This article investigates the effect of tools with different geometry possessing different rake angles when used in ultrasonic-assisted edge trimming operation dealing with multidirectional CFRP laminates. A full-factorial experimental design was adopted to analyze the effect of process parameters typically cutting speed, feed rate, rake angle, amplitude, and their interactions. Machining performance indicators were captured which were the cutting forces, tool wear, chip temperature, and surface roughness. The results showed that UAM mode contributed to an increase in the cutting forces, tool wear, and chip temperature compared to the conventional mode. On the other hand, UAM mode improved the quality of the machined surface. Additionally, the ultrasonic mode enhanced the material removal mechanism using a tool with a negative rake angle. [ABSTRACT FROM AUTHOR]

Many techniques have been developed to improve the machinability of aeronautical materials titanium and nickel-based alloys such as ultrasonic-assisted turning, laser-assisted turning, and cryogenic-assisted turning. This collaborative scientific investigation presents the steps taken to gain insight into the phenomena of machining Nimonic 90 (a nickel-based alloy) alloy using ultrasonically assisted turning. The cutting speed, feed rate, depth of cut, and frequency are taken as input parameters and average surface roughness (Ra), power consumption (P), and chip formation are considered as output parameters. The experiments are carried out with the full factorial design. The UAT (ultrasonically assisted turning) process gives a significant improvement in average surface roughness and power consumption because of the intermittent cutting action of the cutting tool. UAT process shows a 70–80% reduction in average surface roughness (Ra) and a 6–15% reduction in power consumption as compared with CT (conventional turning) process. Ultrasonically assisted turning also resulted in the thin and smoother chips as compared with CT process which helps to achieve a more superior machining effect. Finite element modeling shows that the quasi-static nature of the stress induced in the UAT process leads to lower force and ultimately lower power generation. Moreover, a sustainability assessment model is implemented to investigate the effect of UAT in terms of machining performance as well as sustainability effectiveness in a single integrated approach. The novelty of this work lies in providing an integrated concept that combines experimental analysis and sustainability assessment when using ultrasonic vibrational energy during turning of Nimonic 90. [ABSTRACT FROM AUTHOR]

Titanium alloys are typical difficult-to-machine materials. The experiment is conducted by turning Ti-6Al-0.6Cr-0.4Fe-0.4Si-0.01B (TC7) with PCD and PCBN tools under dry condition. The paper focuses on studying the performance of PCD tools in dry turning TC7 and investigating the machinability of TC7. Wear mechanisms of two cutting tools are analyzed and compared by scanning electronic microscopic (SEM) images of worn inserts. The effect of cutting parameters (cutting speed, feed rate and depth of cut) on tool life is studied by measuring the average flank wear with 3D super-depth-of-field instrument. The influence of cutting parameters on cutting temperature, surface roughness, and surface microhardness is also investigated. The results show that although non-uniform wear band forms on both tools of PCD and PCBN, the wear of PCBN is serious than that of PCD. The adhesion-dissolution-diffusion mechanism takes effect on two tools during machining. For PCD tool, obvious adhesion and chipping occur. For PCBN tool, adhesion, notching, and crater occur. The main conclusion is that PCD tool has better performance than PCBN tool. PCD tool is suitable for machining TC7. The machinability of TC7 is poorer than that of TC4. The hardening of workpiece surface layer occurs. [ABSTRACT FROM AUTHOR]