Search

Introduction Percutaneous screw fixation of the posterior pelvic ring is a popular technique to treat unstable pelvic ring lesions. This technique is practicable in both, the high-energy pelvic ring fractures, mostly in the young population as well as the osteoporotic fractures in the elderly. Risk of the transiliac-transsacral screw positioning is that the critical area of nerve root exit has to be passed twice. For secure screw placement, without causing iatrogenic neurovascular injuries, the knowledge of distances to the narrowest areas is essential. Purpose of this anatomical study was to examine the optimal intraosseous screw placement for the first two sacral segments. Material/methods Images of uninjured pelves from 50 patients (64-line CT scanner) were evaluated. Then virtual transiliac-transsacral srews were positioned into the first two sacral segments. The distance from the screws’ entrance points at the ilium's alar bone to the narrowest portion of the whole pedicle as well as the height and width in this area were measured. Descriptive statistics were used and gender related differences were evaluated using student T-test. Results For the first sacral segment the distance to the narrowest zone amounted in mean 62.75 mm, respectively 63.31 mm, depending on the selected way of measurement. For the second segment the mean distance to the neuroforamina was on average 50.61 mm, respectively 51.54 mm. The average height in S1 measured 25.88 mm and the average width 25.49 mm. The average height for S2 was 17.54 mm and the average width 17.61 mm. We could not find any statistically significant gender correlation for the measured distances. Conclusion Results of this anatomical study may help in performing a safe surgical procedure.

The technique for placing iliosacral screws typically involves the surgeon using an inlet and outlet view as the primary means for assessing the anteroposterior and craniocaudal position of the guidewire, respectively. However, because these views are rarely, if ever, orthogonal to one another, this technique will inevitably lead to unintentional biplanar movements. These unintentional movements, in turn, require correction, which can increase operating room and fluoroscopic time. Here we calculate the degree and magnitude of these unintentional movements. Additionally, we provide a simple technique for minimizing or eliminating them altogether.

BACKGROUND: The aim of this study was to investigate proximal humerus plating regarding drill depth and over penetration of the glenohumeral joint and to find a relation between these findings and different areas of bone mineral density (BMD) in the humeral head. MATERIAL & METHODS: The study sample involved 45 upper extremities from human adult cadavers. Two different plates (HOFER; PHILOS) were applied to the proximal humerus. Each hole was drilled until the respective participant thought to have placed the drill bit subchondral. Next, penetration of the far cortex was conducted to determine the residual bone stock. Additionally, the point of screw penetration of the far cortex was identified for each hole of the plates and allocated to five regions with different bone mineral density as described by Tingart et al. RESULTS: The screw penetration rate and the residual bone stock were compared within the 5 BMD regions. A significantly thicker residual bone stock was found at the central region (SD ± 13.1 mm) than in the anterior region (SD ± 9.5 mm) and in the posterior region (SD ± 8.5 mm). The anterior region revealed a significantly higher penetration rate than the posterior region (p = 0.01) and the central region (p = 0.03). CONCLUSION: The anterior region of the humeral head was associated with a higher over penetration rate of the far cortex into the glenohumeral joint and a decreased bone stock after subchondral drilling representing a reduced bone mineral density (BMD). LEVEL OF EVIDENCE: Cadaver Study. ispartof: INJURY-INTERNATIONAL JOURNAL OF THE CARE OF THE INJURED vol:52 pages:S17-S21 ispartof: location:Netherlands status: published

INTRODUCTION: Following proximal humeral plate osteosynthesis, mechanical complication rates ranging up to 40% have been reported. The study aims to determine the influence of surgeons' experience and the technique of drilling on the complication rate. MATERIALS AND METHODS: The sample involved 45 cadaveric humeri. Six orthopaedic surgeons were divided into two groups with regard to their level of experience (novice versus expert group). On each humerus two different proximal humerus plates were applied. Drillings were performed either with a sharp or worn drill bit (to simulate either sharp or blunt drilling). The respective holes were drilled until the respective participant thought to have placed the drill bit subchondrally, followed by perforation of the cartilage of the humeral head. Both these values and cases of unintended penetration of the articular cavity were evaluated. RESULTS: Fourteen holes (3.6%) were primary penetrated in the joint cavity in the worn-drill-bit-subgroup and 19 holes (5%) in the sharp-drill-bit-group. The latter had an average distance between the chosen subchondral position and the humeral articular surface of 8.3 mm and the worn-drill-bit-subgroup was at 10.6 mm. In the novice group 20 perforations (5.2%) of the joint space occurred and the mean interval between the chosen subchondral point and the humeral articular surface was 4.0 mm. The experienced surgeons showed a perforation rate of 3.4% and were at a mean of 14.9 mm. There were no significant differences regarding drilling manoeuvres and experience. CONCLUSION: Although our results are satisfactory, they can be traced back to the relatively high interval between the respective chosen position of the drill bit and the humeral articular surface which may not guarantee screw stability during ORIF of all fracture patterns. ispartof: INJURY-INTERNATIONAL JOURNAL OF THE CARE OF THE INJURED vol:52 pages:S22-S26 ispartof: location:Netherlands status: published

We describe results of a cadaveric study and an accompanying surgical technique which simplifies posterior-to-anterior axial screw placement into the calcaneus, often utilized during fixation of displaced intra-articular calcaneus fractures or calcaneal osteotomies. By defining the Tuber-to-Anterior Process Angle (TAPA), this technique facilitates axial screw placement, thereby decreasing reliance on intraoperative fluoroscopy and reducing operative time.

INTRODUCTION In iliosacral screw fixation, the dimensions of solely intraosseous (secure) pathways, perpendicular to the ilio-sacral articulation (optimal) with corresponding entry (EP) and aiming points (AP) on lateral fluoroscopic projections, and the factors (demographic, anatomic) influencing these have not yet been described. METHODS In 100 CTs of normal pelvises, the height and width of the secure and optimal pathways were measured on axial and coronal views bilaterally (total measurements: n=200). Corresponding EP and AP were defined as either the location of the screw head or tip at the crossing of lateral innominate bones' cortices (EP) and sacral midlines (AP) within the centre of the pathway, respectively. EP and AP were transferred to the sagittal pelvic view using a coordinate system with the zero-point in the centre of the posterior cortex of the S1 vertebral body (x-axis parallel to upper S1 endplate). Distances are expressed in relation to the anteroposterior distance of the S1 upper endplate (in %). The influence of demographic (age, gender, side) and/or anatomic (PIA=pelvic incidence angle; TCA=transversal curvature angle, PID-Index=pelvic incidence distance-index; USW=unilateral sacral width-index) parameters on pathway dimensions and positions of EP and AP were assessed (multivariate analysis). RESULTS The width, height or both factors of the pathways were at least 7mm or more in 32% and 53% or 20%, respectively. The EP was on average 14±24% behind the centre of the posterior S1 cortex and 41±14% below it. The AP was on average 53±7% in the front of the centre of the posterior S1 cortex and 11±7% above it. PIA influenced the width, TCA, PID-Index the height of the pathways. PIA, PID-Index, and USW-Index significantly influenced EP and AP. Age, gender, and TCA significantly influenced EP. CONCLUSION Secure and optimal placement of screws of at least 7mm in diameter will be unfeasible in the majority of patients. Thoughtful preoperative planning of screw placement on CT scans is advisable to identify secure pathways with an optimal direction. For this purpose, the presented methodology of determining and transferring EPs and APs of corresponding pathways to the sagittal pelvic view using a coordinate system may be useful.

Aim Unstable posterior pelvic ring injuries should be stabilised successfully by percutaneous iliosacral screwing. The intervention takes place under intraoperative fluoroscopic guidance. The inlet and outlet views are crucial and are performed by tilting the image intensifier. Safely interpreting fluoroscopic views can be challenging in certain clinical scenarios. We demonstrated on a series of patients howpreoperative CT scans can be used to anticipate the appropriate intraoperative inlet and outlet fluoroscopic views and positioning of the patient on the operating table, thereby avoiding possible operating table obstacles. Materials and methods We analysed at random 30 pelvic CT scans from patients of different ages and both sexes, utilising the sagittal reconstructions. Inlet and outlet angle measurements were calculated on the scans to determine the appropriate intraoperative inlet and outlet views. Results The analysed CT scans showed an average inlet view of 22.3° (range 10.4°–39.8°) and an average outlet view of 42.3° (range 31.5°–53.1°). Sex and age had no influence on results. The calculated required free space under the operating table for unobstructed tilting of the C-arm was a minimum of 145 cm. Conclusion The significant anatomic variations of the posterior pelvic ring have been well documented in the literature. The angles required to obtain appropriate intraoperative inlet and outlet views are not perpendicular and differ greatly from traditional settings, which directed the beam 45° caudally and 45° cranially. The fluoroscopic beam would need to be angled differently in each patient to obtain ideal cardinal views that ultimately assist in safe iliosacral screw placement. To avoid collision of the C-arm with the operating table, it is essential to provide secure free space under the operating table of at least 145 cm.

The stabilization of an atlantoaxial (C1-C2) instability is demanding due to a complex atlantoaxial anatomy with proximity to the spinal cord, a variable run of the vertebral artery (VA) and narrow C2 pedicles. We perfomed the GoelHarms fusion in combination with an intraoperative 3D imaging to ensure correct screw placement in the C2 pedicle. We hypothesized, that narrow C2 pedicles lead to a higher malposition rate of screws by perforation of the pedicle wall. The purpose of this study was to describe a certain pedicle size, under which the perforation rate rises.In this retrospective study, all patients (n=30) were operated in the GoelHarms technique. The isthmus height and pedicle diameter of C2 were measured. The achieved screw position in C2 was evaluated according to GertzbeinRobbin classification (GRGr).A statistically significant correlation was found between the pedicles size (isthmus height/pedicle diameter) and the achieved GRGr for the right (p=0.002/p=0.03) and left side (p=0.018/p=0.008). The ROC analysis yielded a Cut Off value for the pedicle size to distinguish between an intact or perforated pedicle wall (GRGr 1 or ≥2). The Cut-Off value was identified for the isthmus height (right 6.1mm, left 5.4mm) and for the pedicle diameter (6.6mm both sides).The hypothesis, that narrow pedicles lead to a higher perforation rate of the pedicle wall, can be accepted. Pedicles of6.6mm turned out to be a risk factor for a perforation of the pedicle wall (GRGr 2 or higher). Intraoperative 3D imaging is a feasible tool to confirm optimal screw position, which becomes even more important in cases with thin pedicles. The rising risk of VA injury in these cases support the additional use of navigation.

Fixation strength of constructs placed across the pubic symphysis after injury is dependent on screw length, maximisation of which requires knowledge of the bony anatomy. The aim of this study was to describe the ideal angle of drilling to achieve maximal safe screw placement within the pubic body. Furthermore, the influences of age and gender on the skeletal topography were investigated.Three hundred CT scans of patients without pelvic injury were analysed to record the angle of the pubic body (APB) with respect to the coronal plane, and the depth of the pubic body (DPB) in the sagittal plane.Mean APB and DPB were 54.69° and 55.35mm, respectively. Females had a significantly higher mean APB than males (57.29° vs. 52.41°; p0.001), whereas males had a significant larger mean DPB (59.13mm vs. 51.03mm; p0.001). Age had no effect on the mean APB. Mean width of the pubic body at the base was 9.38mm.The anatomy of this region is reliable in terms of angles and sizes; a drill angle of 55° with respect to the operating table will allow maximal screw length, which should be in the region of 55mm. The mean width of the pubic body should allow for placement of a 3.5 or 4.5mm diameter screw.

Objective To report our experience with a novel alternative method of freehand interlocking of intramedullary nails. This method requires the use of only anterior-posterior image intensification and an intramedullary guide wire to verify screw placement. Our results are compared with historical results in the literature. Methods A total of 815 patients were treated using this technique from January 2008 to December 2012; 603 patients had fractures of the tibia and 212 had fractures of the femur. Results The mean duration of surgery for tibial shaft fractures was 55.6 minutes (range 42–60 minutes) and that for fractures of the femur was 78 minutes (range 50–90 minutes). The mean time for each distal locking was 3.8 minutes (2.5–5.1 minutes), with 7.65 seconds of exposure to radiation during each block. Conclusions The surgical technique is simple, easy and reproducible. Mean time of surgery and radiation exposure was less than that in the literature. A comparative study should be performed.

Tip-apex distance is a well described method for assessment of screw placement in dynamic hip screw fixation of proximal femoral fracture. A distance of25mm is associated with a significantly lower rate of cut out of the fixation device. Measurement is frequently performed retrospectively, although there has been no demonstration as to what accuracy the surgeon has of estimating tip-apex distance from image intensifier images, whilst scrubbed in theatre. Thirty-one clinicians working within orthopaedic departments were tested in their ability to identify adequacy of tip-apex distance on a series of image intensifier images. Level of seniority, awareness of the concept of tip-apex distance and use of the concept in clinical practice were each assessed. The accuracy in identifying the correct TAD was 82.5% in consultants, 83.8% in registrars and 71.1% in Senior house officers (SHO). The method was used in clinical practice by 50% of consultants, 89% of registrars and none of the SHOs.

The aim of this pilot study was to assess a new method of training for peri-acetabular screw placement under indirect vision using standard C-arm fluoroscopy using a porcine model. Two novice orthopaedic residents placed 72 screws (36 each) about the acetabula of six porcine pelves under C-arm fluoroscopic guidance. Unsatisfactory screw position was noted in 22 of 72, with five instances of screw ingress into the hip joint. All of these cases occurred in the first half of each resident's series. Screw direction and final position improved over subsequent trials. This pilot study demonstrates that surgical simulation techniques are applicable in percutaneous screw fixation. Such an approach could be useful for both residents in training and more experienced surgeons who wish to perform this procedure in cases where it is appropriate.

Percutaneous iliosacral screw fixation of the posterior pelvic ring is a demanding procedure with high exposure to radiation. The conventional technique includes the use of three classical projections with the C-arm: inlet, outlet, and true lateral views. A projection in the axis of the upper sacral alar pedicles with a 30° cephalad and 30° ventral oblique view would help in obtaining a more accurate visualization of the safe corridor. Two subcutaneously placed K-wires, one placed horizontally and one vertically, may facilitate the starting point and aim changes by offering the surgeon an option for exactly matching the position of the sacrum with the image. The purpose of this study was to detect if the radiation application could be decreased by our new methodology.Seventeen patients with pelvic posterior ring disruptions, in which percutaneous iliosacral screw placement was indicated, were included in the study. Group 1 comprised 7 patients in whom conventional projections and technique were used. Group 2 comprised 10 patients in whom 30°–30° projection and sacral mapping technique via two subcutaneous K-wires were applied. Radiation exposure time, total fluoroscopic shot count, fluoroscopic shot count needed for only guide wire and screw placement, radiation dose, and complications were compared between the two groups.The median number of fluoroscopic images for guide and screw placement was 132 (56–220) and 29.5 (19–83) in Groups 1 and 2, respectively, and the difference was statistically significant (p0.001). The median total fluoroscopic radiation time was 138 (68–234) and 52 (28–77) s in Groups 1 and 2, respectively, and the difference was significant (p0.001). Group 1 had a significantly higher median radiation dose than Group 2 [3020 (1502–6032) vs. 1192 (426–2359); (p = 0.001)].Iliosacral screw placement with the help of sacral mapping and a fourth view, “30°–30°”, helps the surgeon to markedly reduce the fluoroscopic shots, radiation time and dose during guide wire and screw placement.Therapeutic, Level II.

Achieving good results with intramedullary nailing of oblique long bone fractures at the metaphyseal-diaphyseal junction can be difficult. There is a strong tendency for axial displacement and an association with characteristic malalignment of the short fragment. Poller or blocking screws have been shown to be effective in aiding fracture reduction. While several papers describe methods for screw placement, these are confusing to understand, difficult to follow in clinical practice and not always applicable. Here we describe a new, simple, reproducible and easy to use method for ensuring accurate Poller screw placement, in order to maximise the benefits of their use and achieve good overall results.

Objectives: The AO nail mounted ‘distal locking aiming device’, developed to obtain radiation independent distal locking, has an unproven efficacy in a large clinical setting. This prospective study compares the efficacy and learning curve of the distal aiming device with the popular ‘free hand technique’. Materials and methods: Distal locking in thirty cases of statically locked intramedullary femur nailing using the distal aiming device for rotationally stiff unslotted AO SUN nails was prospectively compared with the same number using the free-hand technique with regard to duration, radiation exposure, accuracy of screw placement, and learning curve. Results and discussion: For the free-hand technique and the distal aiming system respectively, the average distal locking time was 35.8±18.6 versus 19.3±9.8 minutes, and the average number of images taken to achieve distal locking was 11.5±3.4 versus 3.8±3.5. The decrease in average distal locking time by 46.1% and in radiation by 70.0% with the distal aiming system is statistically significant at P Conclusions: We found the AO distal locking aiming device to be an accurate, radiation-independent jig with a short and predictable learning curve.

Objective Locking plates have become ubiquitous in modern fracture surgery. Recently, manufacturers have developed locking plates with polyaxial screw capabilities in order to optimise screw placement. It has already been demonstrated that inserting uniaxial locking screws off axis results in weaker loads to failure. Our hypothesis was that even implants specifically designed for polyaxial insertion would experience a drop-off in resistance when using non-perpendicular screws. Methods Four different types (one monoaxial and three polyaxial locking plates) of readily available small fragment plates were tested. A biomechanical model was developed to test the screws until failure (defined as breakage and rapid loss of >50% force). Screws were inserted at 0, 10 and 15°. Results The standard monoaxial locking mechanism sustained saw a 60% reduction in force (332 N vs. 134 N) when screws were inserted cross-threaded at 10°. Two polyaxial systems saw similar significant reductions in force of 45% and 34%, respectively at 15°. A third system utilizing an end cap locking mechanism showed highly variable results with large standard deviations. Polyaxial screws showed on average only limited reduction at 10 degrees of insertion angle. Conclusion Newer designs of locking plates have attractive properties to allow more surgical options during fixation. However this freedom comes at the price of reduced force. Our results show that the safe zone for inserting these screws is closer to 20°, rather than the 30° indicated by the manufacturers. Also, the various polyaxial locking mechanisms seem to influence the overall resistance of the screws.

The Bonedoc DHS simulator is a virtual reality simulator of screw and plate fixation of hip fractures which runs on a standard PC. We hypothesised that the simulator would be able to discriminate between subjects with different levels of operative experience. Three groups (medical students (MSs), basic trainees (BTs), and advanced trainees (ATs)) performed six virtual operations. Measurements included: reduction position, incision length, misplaced drill-holes, final screw placement, X-rays taken, surgical time as well as computer and operative experience. The accuracy, number of X-rays and speed were significantly different between novices and trainee surgeons (p < 0.01, p < 0.05, p < 0.05). Intra-articular screw penetration by the medical students occurred 12 times, basic trainees 6 times and advanced trainees twice (p < 0.01, MS vs. trainees). Amongst trainees, the advanced trainees placed the lag screw more accurately and took less X-rays (ns). The basic trainees performed the complete procedure fastest at 6 min compared to ATs at 9 min (p < 0.05) but were not as accurate. The Bonedoc DHS simulator provides a means to discriminate between novices and trainee surgeons.

Intramedullary nailing is the standard treatment for closed and some open unstable diaphyseal tibia fractures. Fluoroscopy, while essential for proper nail placement can subject the surgical team and patient to substantial radiation. A new targeting system for tibia nail distal interlocking was developed by Orthofix® to limit fluoroscopy. This prospective clinical study compares the Orthofix® targeting system versus a free-hand technique for the tibial nail distal interlocking. Fifty eight consecutive patients with sixty tibial fractures amenable for nail fixation were randomly assigned into two equal groups: Group 1: Orthofix® distally based distal targeting device and Group 2: a free-hand technique. In all the cases stabilization was achieved with a reamed statically locked tibial nail. Recorded data included accuracy of screw placement, duration of surgery prior to and during distal interlocking, and the fluoroscopy time prior to and during distal interlocking. Both groups revealed comparable fracture patterns. In all fractures the technical aspects of the surgical treatment were performed without complications. There was no statistically significant difference between the groups in the mean time of surgery prior to (62.02 vs. 61.01 min, P=0.92) and during distal interlocking (17.06 vs. 19.08 min, P=0.55), or in the total surgical time (81 vs. 85 min), respectively. Neither was there a statistically significant difference in the mean fluoroscopy time prior to distal interlocking (69 vs. 81 s, p=0.22) nor in the total fluoroscopy time (84 vs. 117 s). There was however, a statistically significant difference between the Orthofix and free-hand groups with regards to the mean fluoroscopy time during distal interlocking (15 vs. 36 s, P=0.01, respectively). This study demonstrates that the distally based distal targeting device by Orthofix® for tibial nailing can significantly decrease the mean fluoroscopy time necessary to complete distal interlocking versus free-hand technique.

Twenty consecutive patients with unstable thoracolumbar fractures were taken up for posterior spinal stabilization using the Steffee VSP system at the earliest opportunity. Patients were followed up from 20 to 38 months. 70% patients were operated within 3 weeks of sustaining injury (group 1) while injury-operation interval exceeded 3 weeks in 30% (group II). The average preoperative kyphotic angle was 19.35 degrees which improved to 8.70 degrees, the correction being much more in group I (17.60 degrees to 5.3 degrees) compared to group II (22.90 degrees to 14.40 degrees). The average preoperative vertebral body height was 57.75% which improved to 79.75%, the correction being much more in group I (61.20 to 88.40%) compared to group II (51.40 to 63.70%). No patients deteriorated neurologically while 7 out of 16 patients with neurological deficit showed improvement by one or more Frankel Grade (43.75%). It is concluded that reasonable correction of deformity, fair chance of neurological recovery and significant reduction of recumbency associated complications can be expected even when surgery is delayed.