Search

The OPA (ORNL-PSERC-Alaska) model has been widely used in cascading failure simulations to predict likely and plausible sequences of cascading failures. This letter focuses on an algorithmic approach to enhance the OPA model whose main engine is based on quasi-steady-state models without considering the impact of collective transient dynamics of the entire system on the sequence of cascading failures. In particular, the enhanced OPA model incorporates dynamically induced cascading failures in fast time scales, which allows it to capture more realistic and detailed cascading scenarios. In this work, we outline the enhanced OPA model and provide simulation results to illustrate its feasibility with the realistic test network. [ABSTRACT FROM AUTHOR]

The letter describes a novel, continuum-based approach, to capture the evolution of electromechanical dynamics in a power network following a disturbance. Such approach is based on the frequency divider formula (FDF), which was recently proposed by the third author. A key point in obtaining the frequency divider formula (FDF) as a consequence of a continuum, is to show that the spatial rate of change, at a given time, of the frequency along a lossless line is constant. The proposed derivation is then compared with the electromechanical wave approach (EWA), which has been discussed in the literature in a variety of hues and is aimed at modeling the propagation in a power system of frequency oscillations following a disturbance. The discussion illustrates similarities and differences between FDF and electromechanical wave approach (EWA). [ABSTRACT FROM AUTHOR]

The increasing complexity of modern AC/DC power systems poses a significant challenge to a fast solution of large-scale transient stability simulation problems. This paper proposes the hybrid parallel-in-time-and-space (PiT+PiS) transient simulation on the CPU-GPU platform to thoroughly exploit the parallelism from time and spatial perspectives, thereby fully utilizing parallel processing hardware. The respective electromechanical and electromagnetic aspects of the AC and DC grids demand a combination of transient stability (TS) simulation and electromagnetic transient (EMT) simulation to reflect both system-level and equipment-level transients. The TS simulation is performed on GPUs in the co-simulation, while the Parareal parallel-in-time (PiT) scheduling and EMT simulation are conducted on CPUs. Therefore, the heterogeneous CPU-GPU scheme can utilize asynchronous computing features to offset the data transfer latency between different processors. Higher scalability and extensibility than GPU-only dynamic parallelism design is achieved by utilizing concurrent GPU streams for coarse-grid and fine-grid computation. A synthetic AC/DC grid based on IEEE-118 Bus and CIGRÉ DCS2 systems showed a good accuracy compared to commercial TSAT software, and a speedup of 165 is achieved with 48 IEEE-118 Bus systems and 192 201-Level detail-modeled MMCs. Furthermore, the proposed method is also applicable to multi-GPU implementation where it demonstrates decent efficacy. [ABSTRACT FROM AUTHOR]

Online transient analysis plays an increasingly important role in dynamic power grids as the renewable generation continues growing. Traditional numerical methods for transient analysis not only are computationally intensive but also require precise contingency information as input, and therefore, are not suitable for online applications. Existing online transient assessment studies focus on the determination of post-contingency system stability or stability margin. This paper develops a novel graph-learning framework, Deep-learning Neural Representation or DNR, for online prediction, of the time-series trajectories of the system states using initial system responses that can be measured by phasor measurement units (PMUs). The proposed DNR framework consists of two sequential modules: a Network Constructor that captures network dependencies among generators, and a Dynamics Predictor that predicts the system trajectories. The key to improved prediction performance is the introduction of the spatio-temporal message-passing operations into graph neural networks with structural knowledge. Its effectiveness and scalability are validated through comparative studies, demonstrating the prediction performance under different contingency scenarios for systems of different sizes. This framework provides a solution to online predicting post-fault system dynamics based on real-time PMU measurements. Additionally, it can also be applied to facilitate the offline transient simulation without simulating the entire trajectories. [ABSTRACT FROM AUTHOR]

In this letter we propose an extension of the Dissipating Energy Flow (DEF) method for locating sources of forced oscillations (FOs), based on an energy function constructed by the complex integral approach, which we call Complex DEF (CDEF). To trace sources of FO, we study the scalar projection of CDEF in a specific direction on the complex plane. We show by simulated cases that this alternative has a good performance in cases where the original DEF fails. [ABSTRACT FROM AUTHOR]

Deep learning (DL) techniques have shown promising performance for designing data-driven power system transient stability assessment (TSA) models. However, due to the deep structure of the DL, the resulting model is always a black-box and hard to explain, which hinders its practical adoption by the industry. This paper proposes an interpretable DL-based TSA model to balance the TSA accuracy and transparency. The proposed method combines the strong nonlinear modelling capability of a deep neural network and the interpretability of a decision tree (DT). Through regularizing DL-based model with the average DT path length in the training process, the proposed interpretable DL-based TSA method can visually explain the TSA decision-making process. Simulation results have shown that the proposed method can deliver highly accurate TSA results and interpretable TSA decision-making rules, which can be used for designing preventive control actions. [ABSTRACT FROM AUTHOR]

This letter develops an equivalent circuit model of a grid-forming (GFM) converter with a circular current limiter and analyzes its transient stability. It is revealed that the inner control loop can be simplified as a voltage source behind an equivalent resistor. Based on the developed model, theoretical analysis and experimental tests demonstrate that the transient stability of a $P-f$ droop-controlled GFM converter with the circular current limiter can be assured whenever there exist stable equilibrium points. [ABSTRACT FROM AUTHOR]

This letter proposes a novel transient stability criterion for power systems with multi-wind farms, which is deduced from power flow and inertia distribution. The variations of acceleration and deceleration power with and without wind integration, instead of the acceleration and deceleration areas themselves, are calculated, in which the power angle swing direction, the transient stability control of wind turbines, the position of wind farms access, and the unbalanced output of synchronous clusters are also considered. The simulation results show the effectiveness of the proposed criterion to distinguish transient stability. [ABSTRACT FROM AUTHOR]

This paper proposes a Principal Component Analysis (PCA)-based method to construct composite indices to rapidly assess power system transient stability. By assigning appropriate weights to a few selected sub-indicators, a composite index can be constructed to guarantee a better coverage of worst-case stability scenarios of the power system. This paper provides an automatic method to construct a composite index with four sub-indicators calculated by the integral of acceleration, speed deviation and rotor angle of generators over a certain integration period using PCA. The effectiveness of the sub-indicators is validated first, followed by a comprehensive example of process of composite index construction, and the assessment of the influence of the effect of integration period on the performance of the composite index. High accuracy of classification has been demonstrated using composite index with appropriate settings of the integration periods of the sub-indicators. [ABSTRACT FROM AUTHOR]

This paper presents a new control strategy for enhancing the dc voltage regulation and the transient response in the multi-terminal VSC-HVDC system by ensuring swift power-sharing among converters when encountering large disturbance such as converter loss or ac fault at one of the converter stations. The quick power sharing can be realized using direct power control (DPC) since it has a merit of fast power dynamic response. On the other hand, to limit the converter current during ac fault, a new coordination strategy between DPC and vector current control (VCC) is proposed. Furthermore, a new simplified model of the MTDC system is developed to study the performance of DPC in enhancing the dc voltage dynamics response analytically. The time-domain simulation of the detailed model of the four converter stations MTDC system verify that the proposed control strategy significantly reduces the overshoot in the transient dc voltage response following an outage or ac fault. As a result, together with the droop gain selection for the maximum permissible steady-state dc voltage deviation, the proposed control strategy can help to reduce the size of the dc chopper in the MTDC grid or even avoiding it. Moreover, the comparative analysis based on time-domain simulation depicts that the proposed simplified model has the same dc voltage response compared to the detailed model of the MTDC system except for a steady-state error of 0.47% and a little bit longer settling time (1.5 ms) at transient. [ABSTRACT FROM AUTHOR]

This paper proposes a Transient Stability Constrained Optimal Power Flow (TSCOPF) formulation that models non-synchronous renewable generation equipped with synthetic inertia. The proposed optimization problem calculates the optimal operating point of the system, accommodating high shares of non-synchronous renewable generation while ensuring transient stability in the event of critical incidents. Synthetic inertia controllers are used to improve the dynamic stability of the system in cases of very high share of renewable generation. The proposed tool is tested in the North-West Spanish system, a network with a high penetration of wind energy that causes a reduction in the total system inertia. The results of the study show that 1) synthetic inertia in renewable power plants can diminish electromechanical oscillations after a severe contingency, reducing the cost of ensuring transient stability; 2) using synthetic inertia the system becomes more stable when conventional generation is decommissioned following de-carbonization and renewable promotion policies; and 3) the proposed model can be used to calculate the parameters of the synthetic inertia control. [ABSTRACT FROM AUTHOR]

It is well known that grid-feeding converters that synchronize to the grid through a Phase-Locked Loop (PLL) can become unstable after a fault. An often-neglected element that plays an important role in the converter synchronization stability is the PLL frequency limiter. While it slows down the phase change during the fault, the frequency limiter also constrains the error of the PLL input, thus leading to a longer settling time. This letter investigates the mechanism of the converter synchronization stability caused by the frequency limiter and provides a taxonomy to evaluate its impact on the overall system dynamic response. [ABSTRACT FROM AUTHOR]

Since the wide application of virtual synchronous generators (VSGs), the power grid faces great challenges in the safe and stable operation due to their limited thermal capacity and weak anti-disturbance ability. During transient period, for example, a fault occurs in the transmission line, the VSG may lose the transient angle stability and provoke the current hard limit. Even if the fault is cleared by tripping of line, it still faces the problem of instability and voltage dips. To address this problem, in this paper, the post-fault large-signal model of VSG is derived first via the travelling waves based fault information acquisition. Subsequently, with the effect of both active and reactive power loops taken into account, a two-stage simultaneous control scheme is proposed for improving the transient stability of VSG, while considering the current limitation during fault state and voltage support after fault clearance. This method is fulfilled by mode switching and an additional feedback control based on the fault signal. Finally, the effectiveness of the proposed method under both symmetrical and asymmetrical faults is verified. Moreover, the application of the proposed method in a multiple VSGs system is also verified. Besides, the robustness to parameter mismatch and the feasible operating region for the method are discussed. [ABSTRACT FROM AUTHOR]

Machine learning approaches have exhibited high potential in power system transient stability assessment (TSA), yet their initial preparation stages of stability knowledge base generation (SKBG) based on time-domain simulations often undergo high computational costs. In fact, how to ease the heavy computational burden of SKBG without sacrificing the reliability is still a significant challenge. To address this problem, this paper develops a semi-supervised ensemble learning (SSEL) framework for reliable SKBG acceleration, without additional need for computing hardware upgrading. In particular, it performs detailed simulations for a minority of cases and fast simulations for the majority ones to reduce the total computation time. Considering the absence of stability status information of those fast simulated cases, an SSEL scheme is systematically designed to reliably label their stability status. Before implementing SSEL, two concise feature descriptors are first introduced to efficiently extract transient features from multiplex system trajectories. Then, all the cases are characterized in a unified feature space, whereby a series of semi-supervised support vector machines are trained in randomly formed subspaces. Afterward, these single machines are systematically combined to derive an enhanced SSEL model, which is able to make reliable and robust labeling decisions. Further, a backtrace strategy is carefully devised for SSEL, so as to maintain the high reliability of SKBG. Test results on the IEEE 39-bus system and the realistic GD Power Grid in South China illustrate the excellent performances of the proposed framework on SKBG acceleration. [ABSTRACT FROM AUTHOR]

In this paper, a distributed predefined-time fractional-order sliding mode controller (DPTFOSMC) is proposed for performance improvement of power system. The proposed DPTFOSMC is designed based on the multi-agent framework and distributed control theory, which can reduce the pressure of central controller in communication and calculation, thus obtaining fast and coordinated response. The DPTFOSMC can achieve the advantages of sliding mode control (SMC) with fast response and strong robustness for the power system. In addition, the power system under the proposed DPTFOSMC can be stabilized in stable range within a predefined time which is directly equal to the tunable parameter, thus meeting the high requirement for convergence time of the power system. The prescribed performance function (PPF) is carried out to design the DPTFOSMC, which can ensure that the power system can achieve the expected transient and steady responses. Meanwhile, fractional calculus is implemented to devise the DPTFOSMC to eliminate the chattering phenomenon of conventional SMC. The Lyapunov function is adopted to analysis the predefined-time stability of the power system under the proposed DPTFOSMC. Simulations are taken to validate the effectiveness and superior performance of the proposed DPTFOSMC for the power system. The results show that the DPTFOSMC can ensure the power system to achieve superior performances than the existing control methods. [ABSTRACT FROM AUTHOR]

Few studies have focused on assessing the transient and steady-state voltage stability status of dynamic systems simultaneously. This motivated us to propose a new concept referred to as joint voltage stability assessment (JVSA). Towards this end, this paper proposes a novel data-driven JVSA method considering load uncertainty. It combines multiple convolutional neural networks (multi-CNNs) and a novel variational Bayes (VB) inference for better JVSA accuracy. First, the multi-CNN model is utilized to fast estimate the maximum voltage deviations during the transient and steady-state process. Uncertain load scenarios and system topology under $N$ -1 contingency with are chosen as inputs of each CNN model. Second, estimated voltage deviations are put into the VB inference to automatically infer the transient and steady-state voltage stability status. To validate its effectiveness, numerical simulations are performed on the modified WECC 179-bus system by comparing with benchmark algorithms. It is demonstrated that the proposed data-driven JVSA method is more accurate and faster than the conventional VSA method. [ABSTRACT FROM AUTHOR]

This paper proposes a finite-time event-triggered secondary frequency and voltage control for islanded AC microgrids (MGs) in a distributed fashion. The proposed control strategy can effectively perform frequency restoration and voltage regulations, while sharing the active and reactive power among the distributed generators (DGs) based on their power ratings. The finite-time control enables a system to reach consensus in a finite period of time enhanced from the asymptotic convergence. The event-triggered communication is utilized to reduce the communication burden among the DG controllers by transmitting data among DGs if an event-triggering condition is satisfied. The performance of the proposed finite-time event-triggered frequency control is verified utilizing a hardware-in-the-loop experimental testbed which simulates an AC MG in Opal-RT. [ABSTRACT FROM AUTHOR]

The proliferation of Phasor Measurement Units (PMUs) to monitor power grid dynamics at a high resolution (10–100 samples/sec) has opened a new paradigm to situational awareness. Existing event detection techniques for identifying multiple events like transmission line faults, generation trip, line trip, load loss, current transformer (CT) failure, islanding, etc., are prone to misdetection, delayed detection, and false detection. Moreover, most of them can detect events either with fast (transient events) or slow dynamics (oscillatory and excursion events) using synchrophasor measurements. This paper focuses on detecting events with both fast and slow dynamics using wide-area frequency measurements. To this end, a novel method is proposed based on Weibull distribution, which we call as Weibull-based Excursion Transient and Oscillatory (WETO) method. The WETO method can identify the time of inception, location, and severity of the event in near real-time using only a single parameter, known as variability. The events are detected within a time window of 5 cycles using only frequency measurements. The proposed method is validated for the Indian as well as the North American grid disturbances, and the results show that it would be beneficial to the system operator in visualizing the true situation of the grid events. [ABSTRACT FROM AUTHOR]

The paper introduces the concept of complex frequency. The imaginary part of the complex frequency is the variation with respect of a synchronous reference of the local bus frequency as commonly defined in power system studies. The real part is defined based on the variation of the voltage magnitude. The latter term is crucial for the correct interpretation and analysis of the variation of the frequency at each bus of the network. The paper also develops a set of differential equations that describe the link between complex powers and complex frequencies at network buses in transient conditions. No simplifications are assumed except for the usual approximations of the models utilized for the transient stability analysis of power systems. A variety of analytical and numerical examples show the applications and potentials of the proposed concept. [ABSTRACT FROM AUTHOR]

Short-circuit current analysis, especially transient current calculation, provides a basis for protection design. Because the control systems of inverter-interfaced renewable energy sources have a high degree of nonlinearity, it is difficult to analyze the transient current. To address this issue, in this work, a nonlinear differential equation of transient current of symmetrical fault is derived while considering the saturation characteristics of the current loop. Aiming at the solution of this nonlinear differential equation, an analysis method based on the phase plane is proposed, which makes use of the linear relationship between the current deviation and its derivative to simplify the direct determination of the nonlinear working state in the time domain. The analytical expression of the transient current can then be obtained by the inverse transform from the phase plane to the time domain. The proposed calculation method is verified by both simulations and field tests. [ABSTRACT FROM AUTHOR]

This paper deals with the transient stability of a grid-forming converter while embedding a current reference saturation strategy. The novelty of this work consists in investigating the impact of the current reference angle on the transient stability. In case of a balanced voltage sag, analytical formulas to estimate the critical clearing angle (CCA) and critical clearing time (CCT) while considering different values of the current reference angle are derived. It is demonstrated that the choice of this angle is constrained by the ability of the power converter to switch back to the voltage control mode. Based on that, its optimal value that enhances the transient stability and allows a switching from the saturated current control mode to the voltage control mode is calculated. Thereafter, the effectiveness of this optimal choice to guarantee the stability in case of a phase shift caused by a line re-closing event is verified. Time-domain simulations and experimental tests validate the correctness of the presented theoretical approaches. [ABSTRACT FROM AUTHOR]

Transient stability of a power system can be significantly affected by wind power generators due to their stochastic power output and complex dynamic characteristics. This paper proposes a robust optimization approach for coordinating generation dispatch and emergency load shedding against transient instability under uncertain wind power output. The problem is modelled as a two-stage robust optimization (TSRO) model considering transient stability constraints, where the first-stage is to optimize the generation dispatch (preventive control) before a contingency and the second-stage decision is the emergency load shedding (emergency control) after the contingency occurrence under the worst case of wind power variation. To solve this TSRO problem, this paper also proposes a solution algorithm which integrates transient stability assessment and transient stability constraint construction in a column and constraint generation framework. The proposed method is validated on the New-England 39-bus system and the Nordic32 system, which shows high computational efficiency and stability robustness against uncertain wind power. [ABSTRACT FROM AUTHOR]

With the expanding role of converter-interfaced distributed energy resources, modern power grids are evolving towards low-inertia networks that are increasingly vulnerable to extreme dynamics. Consequently, advanced signal processing techniques are needed to accurately characterize measured signals in power systems during non-stationary conditions. However, as advocated by recent literature, state-of-the-art phasor estimation methods are unable to sufficiently capture the broadband nature of these signal dynamics since they rely on a quasi-steady state, single tone model. Inspired by previous work by the authors, this paper proposes a signal processing method that uses a dictionary of kernels, modeling common signal dynamics, to compress time-domain information into a few coefficients. The identified signal model and the extracted coefficients capture the broadband spectrum of typical power system signal dynamics and allow for an improved reconstruction of the measured signal. [ABSTRACT FROM AUTHOR]

The paper proposes methodology for development of dynamic equivalent model of hybrid renewable energy source (HRES) plant suitable for reliable assessment of the overall transient stability of the realistic, large power systems. Transient stability index is used for system stability assessment, and consequently for the evaluation of the model performance. The historical plant production data and transmission network short-circuit fault statistics, together with probabilistically modelled uncertainties associated with system operation, are used to generate a set of realistic dynamic responses of the plant over the period of one year. The use of clustering algorithms enabled unsupervised grouping/clustering of responses and development of the low order equivalent models in the form of a transfer function with voltage as an input and real and reactive power as outputs. The methodology is illustrated on a number of case studies using two HRES plant configurations. It is demonstrated that a very few low order dynamic models can be used to model the HRES plant during the year for sufficiently accurate transient stability assessment of the power system. The possibility of deriving these equivalent models based on forecasted HRES plant composition makes them attractive for practical application in power system dynamic security studies. [ABSTRACT FROM AUTHOR]

Power system control and transient stability analysis play essential roles in secure system operation. Control of power systems typically involves highly nonlinear and complex dynamics. Most of the existing works address such problems with additional assumptions in system dynamics, leading to a requirement for a complete and general solution. This paper, therefore, proposes a novel control framework for various power system control and stability problems leveraging a learning-based approach. The proposed framework includes a two-module structure that iteratively and jointly learns the candidate Lyapunov function and control law via deep neural networks in a learning module. Meanwhile, it guides the learning procedure towards valid results satisfying Lyapunov conditions in a falsification module. The introduced termination criteria ensure provable system stability. This control framework is verified through several studies handling different types of power system control problems. The results show that the proposed framework is generalizable and can simplify the control design for complex power systems with the stability guarantee and enlarged region of attraction. [ABSTRACT FROM AUTHOR]

Fundamental sensor feedback limitations for improving rotor angle stability using local frequency or phase angle measurement are derived. Using a two-machine power system model, it is shown that improved damping of inter-area oscillations must come at the cost of reduced transient stability margins, regardless of the control design method. The control limitations stem from that the excitation of an inter-area mode by external disturbances cannot be estimated with certainty using local frequency information. The results are validated on a modified Kundur four-machine two-area test system where the active power is modulated on an embedded high-voltage dc link. Damping control using local phase angle measurements, unavoidably leads to an increased rotor angle deviation following certain load disturbances. For a highly stressed system, it is shown that this may lead to transient instability. The limitations derived in the paper may motivate the need for wide-area measurements in power oscillation damping control. [ABSTRACT FROM AUTHOR]

The transient stability of traditional power systems is concerned with the ability of generators to stay synchronized with the positive-sequence voltage of the network, whether for symmetrical or asymmetrical faults. In contrast, both positive- and negative-sequence synchronizations should be of concern for inverter-based generation (IBG) under asymmetrical faults. This is because the latest grid codes stipulate that IBG should inject dual-sequence current when riding through asymmetrical faults. Currently, much less is known about the synchronization stability during asymmetrical faults. This significantly differs from the positive-sequence synchronization alone because the coupled dual-sequence synchronization is involved. This paper aims to fill this gap. Considering the sequence coupling under asymmetrical faults, the dual-sequence synchronization model of IBG is developed. Based on the model, the conditions that steady-state equilibrium points should follow are identified. The conditions throw light on the possible types of synchronization instability, including the positive-sequence dominated instability and the negative-sequence dominated one. For different types of instability, the dominant factors are analyzed quantitatively, which are reflected by the limit on the current injection amplitude. Exceeding the limit will lead to the loss of both positive- and negative-sequence synchronizations. The model and the analysis are verified by simulations and hardware-in-the-loop experiments. [ABSTRACT FROM AUTHOR]

A large number of non-linear hardware and control units exists in power electronic system used in grid connected devices. The analytical transient stability analysis of grid-connected converters presents numerous difficulties. A common method to tackle this problem is the stability analysis using Lyapunov’s method. By applying this method, difficulties arise not only from finding a suitable Lyapunov function, but also from checking the constraint of Lyapunov stability. If the appropriate Lyapunov function is a high-order polynomial, it is very challenging to test if it meets the constraints of Lyapunov stability in certain regions. In this paper, the sum-of-squares programming method is used to obtain the estimation of a converter’s domain of attraction with a relatively small number of iterations compared to classically applied methods, such as the Monte Carlo method. The estimation of the domain of attraction are verified by time-domain simulations and StarSim’s controller hardware-in-the-loop tests in this paper. [ABSTRACT FROM AUTHOR]

Data-driven transient stability assessment (TSA) models are usually sensitive to system scale changes and require dynamic information from time-domain simulation (TDS) as inputs. We propose a System-scAle-FreE Transient Contingency Screening (SAFE-TCS) scheme based on only the steady-state measurements. An analytical model is set up to estimate the state variation at fault occurrence ($t_{0+}$) snapshot, which forms multi-graph inputs together with the steady-state information. A novel pooling-ensemble multi-attention graph convolutional network (PE-MAGCN) realizes the spatio-temporal graph embedding, in which an inter-graph convolution link works for the temporal abstraction. Following a pooling-ensemble mechanism, PE-MAGCN derives a fixed-size expressive vector for task-specific networks. This promotes the robustness of the model against system extension. The advantages of SAFE-TCS also benefit from the coordination of various training tricks, including channel attention, category-balanced sampling and joint-decoupling learning, etc. Test results on IEEE 39 Bus system and IEEE 300 Bus system indicate the superiority of the proposed scheme over existing models and its adaptability under various scenarios. [ABSTRACT FROM AUTHOR]

The letter provides a geometrical interpretation of frequency in electric circuits. According to this interpretation, the frequency is defined as a multivector with symmetric and antisymmetric components. The conventional definition of frequency is shown to be a special case of the proposed theoretical framework. Several examples serve to show the features, generality as well as practical aspects of the proposed approach. [ABSTRACT FROM AUTHOR]

Recent studies have demonstrated the potential of flexible loads in providing frequency response services. However, uncertainty and variability in various weather-related and end-use behavioral factors often affect the demand-side control performance. This work addresses this problem with the design of a demand-side control to achieve frequency response under load uncertainties. Our approach involves modeling the load uncertainties via stochastic processes that appear as both multiplicative and additive to the system states in closed-loop power system dynamics. Extending the recently developed mean square exponential stability (MSES) results for stochastic systems, we formulate multi-objective linear matrix inequality (LMI)-based optimal control synthesis problems to not only guarantee stochastic stability, but also promote sparsity, enhance closed-loop transient performance, and maximize allowable uncertainties. The fundamental trade-off between the maximum allowable (critical) uncertainty levels and the optimal stochastic stabilizing control efforts is established. Moreover, the sparse control synthesis problem is generalized to the realistic power systems scenario in which only partial-state measurements are available. Detailed numerical studies are carried out on IEEE 39-bus system to demonstrate the closed-loop stochastic stabilizing performance of the sparse controllers in enhancing frequency response under load uncertainties; as well as illustrate the fundamental trade-off between the allowable uncertainties and optimal control efforts. [ABSTRACT FROM AUTHOR]

Generation expansion planning (GEP) can be a challenging problem when short-circuit (SC) levels and transient stability constraints are considered. We propose a multi-period GEP model in which resistive superconducting fault current limiters (SFCLs) are deployed to limit SC levels, which may be elevated by new generators, and to enhance transient stability at the same time. Through investigating the effect of SFCLs on transient stability and SC levels, efficient linear regions of SFCL deployment are identified and employed to achieve a more cost-effective solution and enhance problem tractability. An effective solution method is also presented by decomposing the main problem into smaller ones. We also propose a linearized AC network framework incorporating bilinear terms based on McCormick envelopes. Relaxation errors are minimized by an exactness loop until the linearized model solution sufficiently matches the original nonlinear model solution. The methodology is illustrated and discussed using the IEEE 118-bus test system. [ABSTRACT FROM AUTHOR]

This paper presents a novel approach to dynamic phasor-based transient stability simulation. The proposed method is based on the modified nodal analysis (MNA) approach to circuit simulation, which is used to construct continuous differential-algebraic equations (DAEs). The proposed method makes use of the stamp technique, which makes it possible to construct a general purpose MNA-based simulator. Stamp-based models for common power system components are derived in this work. A new MNA-based synchronous machine model is presented, which represents machines as nonlinear inductances instead of subtransient equivalents. The resultant continuous DAEs are numerically solved using the general purpose variable step and variable order library IDA. Simulation results from the IEEE 68 bus test system, a real 400 bus power system, and the IEEE 39 bus test system with an embedded HVdc transmission system demonstrate that the proposed method is suitable for large ac networks with power electronic devices. The results demonstrate good agreement between the proposed method and electromagnetic transient (EMT) simulation. The results also demonstrate that the proposed method is fast and scalable with CPU times that are up to 200 times faster than EMT simulation. [ABSTRACT FROM AUTHOR]

While many machine learning approaches have been widely applied to power system online dynamic stability assessment, how to sufficiently learn spatial-temporal correlations from system transients without losing the interpretability is still a challenging issue. In this paper, a novel networked time series shapelet learning approach is proposed to learn spatial-temporal correlations for transient stability assessment (TSA) in an interpretable manner. Specifically, a network impedance-based adjacency matrix is first introduced to characterize spatial networked correlations. Based on graph structural regularization, this matrix is effectively incorporated into the subsequent learning procedure as spatial constraints. Taking time series trajectories acquired from multiple buses as the inputs, networked shapelet learning is heuristically performed to learn critical sequential features, i.e., networked shapelets, for TSA model derivation. With the learning procedure strategically guided by inherent spatial-temporal correlations of the system, the obtained data-driven TSA model is able to perform highly reliable and interpretable online TSA. Numerical test results on the IEEE 39-bus test system and the realistic GD Power Grid in China verify the superior performances of the proposed approach. [ABSTRACT FROM AUTHOR]

Deep learning is considered to be a promising method for total transfer capability (TTC) evaluation due to its high speed and accuracy for nonlinear and complicated problems. However, the operating scenarios of power systems are complex and ever changing. It is difficult to train a single deep model using an overly complex dataset containing operating scenarios with high variability. In addition, making the deep model transparent to validate for operators is another challenge to its application in the power system. To enable the practical application of deep models in TTC evaluation, the operating sample space is clustered into simpler spaces via a two-stage clustering method, and the idea of neighborhood model for the deep TTC evaluation network (DTEN) is proposed. Then, the local post hoc interpretability for the DTEN based on first-order control variable sensitivity is presented. During the interpretability analysis, the quasi-steady state is introduced to assess the coupling effects among different inputs. Case studies on the IEEE 39-bus system and a real-world regional system in China validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Polynomial approximation based on collocation method is an emerging technique to establish the relationship between changeable parameters and interested transient trajectory in a given parameter space. If transient stability region boundary (TSRB) exists in the parameter space, the approximation may have low accuracy due to the high sensitivity of the real trajectory with respect to parameters on TSRB. Utilizing the approximated trajectory and the high sensitivity characteristic, this letter proposes a complementary method to obtain TSRB by calculating the local maxima of a sensitivity-based index. The effectiveness of the method is verified in IEEE 39-bus test system. [ABSTRACT FROM AUTHOR]

Dynamic state estimation (DSE) accurately tracks the dynamics of a power system and provides the evolution of the system state in real-time. This paper focuses on the control and protection applications of DSE, comprehensively presenting different facets of control and protection challenges arising in modern power systems. It is demonstrated how these challenges are effectively addressed with DSE-enabled solutions. As precursors to these solutions, reformulation of DSE considering both synchrophasor and sampled value measurements and comprehensive comparisons of DSE and observers have been presented. The usefulness and necessity of DSE based solutions in ensuring system stability, reliable protection and security, and resilience by revamping of control and protection methods are shown through examples, practical applications, and suggestions for further development. [ABSTRACT FROM AUTHOR]

Co-simulation of heterogeneous systems allows for in-depth analysis of various aspects of power systems’ operation while staying within the environments of the simulation tools that are best fit to represent their respective domains. Equipped with a proprietary co-simulation platform, the paper focuses on the issue of power-conjugate coupling between parts of power grids modeled in transient stability and electromagnetic transient simulation tools. The problems of co-simulation stability and precision in presence of delays are tackled by means of designing a proper coupling interface. It is shown that two established interface methods – the V-I method and the Transmission Line Interface – are special cases of a generalized interface framework proposed in the paper. Moreover, a new interface algorithm is described by parametrizing the generalized framework. Analytical tools are also formulated to aid in the analysis of interface stability and precision via the concepts of passivity and transparency. Simulation results of benchmark systems of various complexity demonstrate the application of the developed power coupling interface. [ABSTRACT FROM AUTHOR]

In this paper, a Frequency Stability Constrained Unit Commitment (FSCUC) model is presented. The on/off status of generating units, generation levels and operating reserves are optimized to minimize the operational daily costs. The frequency stability constraints are included in the proposed FSCUC model to guarantee the safety of System Frequency Response (SFR) under sudden generation outages. A new multi-area SFR model is proposed to capture the regional dynamics of system frequency with considering the impacts of transmission network. An SFR model is developed for each electric region and then the resulted regional SFRs are coupled via a set of constraints. In order to enhance the primary SFR and keep the daily operating point at its economic schedule, Flywheel Energy Storage (FES) devices are utilized in the proposed FSCUC model. The proposed multi-area SFR model allows the optimal allocation of operating reserve and the accurate modeling of FESs in FSCUC model. The proposed FSCUC model is formulated as a Mixed Integer Linear Programming (MILP) problem and is applied over the IEEE 118-bus test system to show the accuracy of the proposed multi-region SFR and the impact of FES in frequency support. The developed MILP model is solved using CPLEX in GAMS. [ABSTRACT FROM AUTHOR]

With the decrease in system inertia, frequency security becomes an issue for power systems around the world. Energy storage systems (ESS), due to their excellent ramping capabilities, are considered as a natural choice for the improvement of the frequency response following major contingencies. In this paper, we propose a new strategy for energy storage – frequency shaping control – that allows to completely eliminate the frequency Nadir, one of the main issues in frequency security, and at the same time tune the rate of change of frequency (RoCoF) to a desired value. With Nadir eliminated, the frequency security assessment can be performed via simple algebraic calculations, as opposed to dynamic simulations for conventional control strategies. Moreover, our proposed control is also very efficient in terms of the requirements on storage peak power, requiring less (up to 40% in one of the cases) power than conventional virtual inertia approach for the same performance. [ABSTRACT FROM AUTHOR]

This paper presents an optimal transient-stability control strategy that modulates the real power injected and absorbed by distributed energy-storage devices. These devices are located at the high-voltage bus of several generators in a synchronous power system. The system is broken into areas based upon groupings of generators. The control strategy consists of two parallel feedback loops. One loop focuses on preserving the synchronism of the generator to its own area. The second loop focuses on preserving the synchronism of a given area to the other areas. Each control loop strategy is based upon local and center-of-inertia frequency measurements. The strategy is derived from two perspectives. With the first, the goal is to remove as much kinetic energy gained during a disturbance as quickly as possible before it is converted to potential energy. With the second perspective, an optimal transient control cost-function is minimized. Both perspectives result in the same strategy. The performance of the control strategy is evaluated on a four-machine power system model and on a 34-generator reduced-order model of the western North-American grid. The results show that this control approach significantly improves the transient stability of power systems. [ABSTRACT FROM AUTHOR]

Line-switching operations introduce several concerns to microgrid operators since they trigger reliability and power quality issues in addition to increasing the wear and tear cost of switching devices. This paper proposes a novel methodology for achieving seamless line-switching in low-inertia islanded microgrids. The proposed methodology aims at mitigating the detrimental line-switching impacts by minimizing the power flow in the switched lines at the moments of executing the switching operations. The minimization of the power flow is realized by optimizing the droop control parameters of the DGs during the transition from one network topology to another. Besides, during executing a series of line-switching operations, the sequence of switching is also optimized to minimize the total switched power. While optimizing the line-switching execution sequence, the transitional droops are optimized for each line-switching operation within that sequence. A dynamic mixed-integer nonlinear programming problem is formulated to find both the optimized dynamic transitional droops and line-switching sequence simultaneously. Simulation results demonstrate the effectiveness of the proposed seamless line-switching methodology where the switched power can be reduced by more than 80% for a single line-switching operation and 54% considering a series of four switch exchanges in addition to achieving several instances of zero-current switching. As a result, a significant decrease in the peak of voltage transients has been recorded for some cases. [ABSTRACT FROM AUTHOR]

This letter proposes an online control strategy to enhance the overall damping of low-frequency power system oscillations of large inter-connected electrical networks. To achieve this objective, the proposed approach employs wide area measured signals to estimate an accurate online model of power system dynamics using the dynamic mode decomposition with control (DMDc) method. The DMDc technique applies singular value decomposition (SVD) to the collected data matrices such that an accurate low-order approximation of system dynamics is obtained. The estimated model is thereafter utilized in designing the wide area damping controller (WADC) using discrete linear quadratic regulator (DLQR). Furthermore, kalman filtering is deployed to update the states of the designed controller and to remove the noise that is contained in the measured signals. The effectiveness of the proposed method is tested on the 10 machines, 39-bus New England test system. [ABSTRACT FROM AUTHOR]

Recently, a hybrid average-value/detailed modeling technique has been presented for efficient electromagnetic transient (EMT) simulation of power systems containing ac–dc line-commutated rectifiers (LCRs). In this letter, the hybrid modeling methodology is extended to consider asymmetrical operation of LCRs due to internal faults of switches. The hybrid model permits large time-steps as opposed to conventional switching models that require precise handling of switching events and respectively small time-steps. The extended hybrid model is also demonstrated to possess numerical advantages over the existing state-of-the-art average-value models (AVMs) of faulty LCRs while providing more accurate results. [ABSTRACT FROM AUTHOR]

This paper proposes a systematic and general approach to model correlated stochastic processes in power systems by means of stochastic differential-algebraic equations. The paper discusses the theoretical background of stochastic differential-algebraic equations and provides a variety of examples of correlated stochastic models for power system applications. With this aim, stochastic processes with Normal and Weibull distributions are considered. The case study utilizes the well-known two-area system to demonstrate that the presence of correlation between the stochastic processes can cause instability, despite the fact that the same system is stable if the same processes are uncorrelated. The case study also considers a 1479-bus dynamic model of the all-island Irish transmission system to show the scalability of the proposed technique, and to compare scenarios with different levels of correlation among stochastic processes. Results indicate that correlation has a non-negligible impact on short-term dynamics. A high level of correlation among the processes, in fact, can give raise to instability. [ABSTRACT FROM AUTHOR]

The commutation failure (CF) is the most common fault in line-commutated high voltage direct current (LCC-HVDC) systems that may lead to the transient overvoltage in the sending-side system. In the worst condition, the CF may lead to large-scale wind turbine tripping. To resolve this problem, the mathematical relationship between the reactive power consumed by the rectifier and DC voltage, DC current is derived. Then, a transient overvoltage calculation method is proposed in this paper. Furthermore, the mechanism of transient overvoltage caused by the CF is analyzed; it is revealed that the reason for three times transient overvoltage is the rapid decrease of the reactive power consumed by the rectifier during the CF and the recovery period from the CF. This paper proposes a constant reactive power control (CRPC) to inhibit transient overvoltage of the sending-side AC system. The proposed CRPC can increase the reactive power consumed by the rectifier, reduce the exchange reactive power between AC and DC systems, and suppress the transient overvoltage. A simulation model in PSCAD serves to verify the proposed CRPC on the transient overvoltage suppression in the situation of different fault types, fault duration, fault severity and short circuit ratio (SCR). [ABSTRACT FROM AUTHOR]

The Virtual Power Plant (VPP) has been proposed to aggregate Distributed Generations (DGs) to act like a single power plant, thus, also has functions on the frequency and voltage support. The previous models of the VPP are static and focus on the energy trading and management. For the system transient response analysis, a dynamic VPP model must be needed. The paper proposes a reduced-order yet accurate aggregated model to represent VPP transients for the stability analysis of power systems. The goal is to provide a model that is adequate for system studies and can serve to the Transmission System Operator (TSO) to evaluate the impact of VPPs on the overall grid. The proposed model can accommodate the transient response of the most relevant controllers included in the distributed generators that compose the VPP. Using a comparison with a real-time detailed Electro-Magnetic Transients (EMT) models of the VPP confirms the validity of the proposed aggregated model. The case studies based on the IEEE 39-bus system verifies the accuracy of the proposed aggregated model on the system stability analysis. [ABSTRACT FROM AUTHOR]

In transient stability simulators such as PSS/E, the bus frequency is estimated using a window of (positive-sequence) phasor angle measurements. A digital filter is often used to account for the filtering effect in actual measurement devices and to eliminate sudden changes during frequency computations. Although transient stability simulators label the filtered angle derivative as the “frequency,” the frequency provided by such programs does not match actual measurements reported by phasor measurement units (PMUs), which makes it difficult to gauge the validity of studies (e.g., wide-area event detection and control applications) that are based on such simulations. In this paper, we implement a frequency computation method directly using positive phasor angles provided by simulators. The proposed method is tested on two systems extensively and validated against the measurements of an actual PMU. The improved frequency measurements closely match PMU responses. Cross-validation results also suggest the method may be used for other systems without conducting full time-domain simulations. [ABSTRACT FROM AUTHOR]

This letter devises a quantum electromagnetic transients program (QEMTP) which is the first attempt to tackle the computational challenges in solving EMTP through quantum computing. The main contributions lie in: (1) A quantum-enabled EMTP formulation with Dommel's model encoded in quantum states; 2) An Harrow-Hassidim-Lloyd (HHL)-based QEMTP to solve the discrete-time nodal equations; 3) An iteration-based HHL revision for mitigating temporal errors to achieve high accuracy of QEMTP with limited quantum resources. Case studies verify the correctness and efficacy of QEMTP in simulating both fast and slow dynamics. [ABSTRACT FROM AUTHOR]

In practical power systems, it is still very challenging to figure out a cost-effective undervoltage load shedding (UVLS) scheme that can reliably and adaptively react to the short-term voltage stability (SVS) problem. Faced with this challenge, this paper develops an intelligent data-driven predictive UVLS scheme for online SVS enhancement. Inspired by valuable ideas in model predictive control and supplementary excitation control in power systems, a novel deep feedback learning machine (DFLM) is designed to precisely predict future voltage violations after UVLS execution. With the help of the DFLM, the UVLS scheme is aware of potential effects of various candidate UVLS actions. Owing to this desirable nature, it can adaptively respond to diverse SVS conditions and optimize UVLS decisions in a non-iterative way. Further, two well-designed strategies, i.e., stepwise constraint relaxation and incremental DFLM adaptation, are introduced to enhance the scheme's reliability and adaptability during online application. Numerical test results on the Nordic test system and the realistic North GZ Power Grid in China showcase the excellent performances of the proposed scheme. [ABSTRACT FROM AUTHOR]