Search

This paper describes a flow control of the dye in the paper mill with the quasi-Z-source indirect matrix converter (QZSIMC) fed induction motor drive. More than a decade the voltage-source inverter (VSI) and current-source inverter (CSI) have been used to control the speed of the induction motor, which in turns controls the flow of dye. Recently, the matrix converter (MC) has been an excellent competitor for the VSI or CSI for its compactness. The voltage transfer ratio of the VSI, CSI, and MC has been limited to 0.866. Thus, the efficiency of these converters is less. To improve the voltage transfer ratio the quasi-Z-source network (QZSN) is to be used between voltage source and indirect MC (IMC). The modification in the shoot-through duty ratio of the QZSN varies the voltage transfer ratio greater than 0.866. Different voltage transfer ratios are needed for different voltage sag conditions. For a variation of the duty ratio of the QZSN, the fuzzy logic controller has been presented. To control the IMC vector control with space vector modulation has been presented. This paper proposes the implementation of QZSIMC adjustable speed drive for the flow control of dye in paper mill during different voltage sag conditions. A 4-kW prototype has been built and the effectiveness of the proposed system is verified with simulation results and experimental setup. Simulation is done in MATLAB, Simulink platform. Experimental setup is done with the aid of a TMS320F2812 (Texas Instrument) processor. The experimental results validate the maintenance of the speed of an induction motor at the set condition, thus controlling the perfect flow of dye in paper manufacturing technology. [ABSTRACT FROM AUTHOR]

Voltage-controlled three-phase three-leg inverters are widely applied in various occasions. The inverters are generally switched to the current-controlled mode to limit the fault currents when short-circuit faults happen. Under symmetrical fault, the inverter can be controlled as a symmetrical, three-phase current source. However, the voltage limiting will happen under asymmetrical fault. As a result, the fault phase currents will be distorted and cannot be completely controlled. Considering that the voltage limiting is mainly caused by large load impedance of healthy phase under asymmetrical fault, the voltage limiting is avoided by paralleling the virtual impedance with the output filter capacitor in this paper. As a result, the current limiting loop is not broken and the fault phase currents can be effectively controlled. The implementation of virtual impedance in control system and the influence of virtual impedance on the stability of system are also analyzed in detail in this paper. The theoretical results are validated by experiments. [ABSTRACT FROM AUTHOR]

The editors discuss the health of the Transactions, the rate of article submission, the time from submission to publication, and the Journal Citation Reports (JCR) Impact Factor of the Transactions and contributing factors for that value. They note that the Transactions have only 100-150 articles waiting for publication, and keeping in mind 45-50 articles are needed for each issue, this is a short and manageable backlog. By making the electronic versions of manuscripts available so far ahead of time, articles are available for a longer time, and there is a good chance for more citations, which should increase the impact factor of the IEEE TRANSACTIONS ON POWER ELECTRONICS (TPEL). In 2007, TPEL published 2600 pages, and it has gradually been increased to 4000 pages in 2011, 5000 pages in 2012, and 5500 pages are projected for 2013. We have decided to publish 12 printed issues so every month a new issue will be printed. A graph is provided showing the number of regular papers received in the past years as well as the number of published pages in the TPEL. Finally they note that in 2008, TPEL obtained a record high value for the impact factor (as shown in a figure) but in 2009 it was reduced a little. In 2010, they saw an increase and were among the top 10 of all published EE journals on a global scale. In 2011, it further increased to 4.6 which is a record high. There are three main reasons for our success: 1) the time from submission to publication has been significantly reduced? allowing the papers to be read over a longer time span; 2) Web of Science (ISI Thomsen Reuter) began to register new power electronics conferences in their database, and citations from conferences counts and contributes to a higher impact factor. [ABSTRACT FROM AUTHOR]

Presents the introductory editorial for this issue of the publication. [ABSTRACT FROM AUTHOR]

Recently, multiple static synchronous compensator (STATCOM) units have been adopted in power transmission systems in order to obtain a better voltage regulation and to share loads. However, they could possibly interact in a negative way instead of helping each other, due to the improper design of the STATCOM controllers. To analyze this problem, a d–q frame impedance-based stability analysis was used to explore the instability with the presence of STATCOMs, where previous stability-related findings are not applicable directly because of some unique features of STATCOMs. This paper identified the frequency range of interactions in a viewpoint of d–q frame impedances and pinpointed that the ac voltage regulation was the main reason of instability, masking the effects of phase-locked loop on power transmission systems. In addition, due to the high impedance of STATCOMs around the frequency range of interactions, the number of connected STATCOMs was the main contributor to stability instead of the topology of power systems or the locations of STATCOMs. A scaled-down 2-STATCOM power grid was built to verify the conclusions experimentally. This paper is accompanied by a video showing instability between STATCOMs in the experiment. [ABSTRACT FROM AUTHOR]

Collaborative control of power converters operating in microgrids with unbalanced single-phase loads is difficult to achieve, considering that the voltages and currents have positive-, negative-, and zero-sequence components. In this paper, a new control scheme for collaborative control of four-leg microgrids is proposed. The main advantage of the proposed methodology is simplicity, because the sharing of the powers produced by the positive-, negative-, and zero-sequence voltage and currents is simple to achieve using the easy to implement and well-known droop control algorithms, i.e., as those based on $P$ – $\omega$ and $Q$ – $v$ droop control. The proposed droop algorithms do not require high bandwidth communication channels and the application of virtual impedances, whose design usually demands extensive simulation work, is not required. Three secondary control systems are also analyzed, discussed, and implemented in this paper to regulate the frequency, voltage, and phase at the point of common coupling (PCC), to achieve a balanced 50-Hz three-phase voltage supply in the PCC during steady-state operation. For these secondary control systems, single-phase phase-locked loop based on quadrature signal generators are implemented. Small signal modeling and design are discussed in this paper. A microgrid prototype of $\approx$ 5 kW, implemented using two power converters of 3 kW (each), is used to experimentally validate the proposed algorithms. [ABSTRACT FROM AUTHOR]

This paper presents a scheme for rotor position estimation from standstill to nominal speed. The proposed scheme is particularly suited for surface mounted permanent magnet synchronous motors and for slotless permanent magnet synchronous motors with completely smooth cylindrical rotor, which cannot be operated with state-of-the-art sensorless methods seamlessly from standstill. At standstill and very low speed, the position is estimated by using signal injection. A systematic distortion in the position estimation that is due to asymmetries in the motor parameters is identified and compensated. The rotor polarity is identified by a special process based on the estimation of the back electromotive force (back EMF) induced by a minimal rotor motion. At high speed, the position is estimated by using a linear back EMF observer. Different observer gains are used at different speed ranges, so that the position estimate is reliable even at low speed. The combination of these two approaches enables sensorless motor control in the full speed range including standstill. Experiments demonstrate the accuracy of the proposed estimation scheme and its robustness under different thermal conditions. This paper is accompanied by two videos demonstrating sensorless operation. [ABSTRACT FROM AUTHOR]

This paper proposes a resonant switching cell model to analyze and design the single-ended resonant dc–dc converters. The single-ended zero-voltage switching (ZVS) converters such as the Class E converter are efficient for megahertz switching because they feature low turn-on and turn-off switching losses. Also, they use only a ground-referenced switch, allowing a simple gate drive circuit. In this paper, we investigate the single-ended resonant converter with the small input inductance, whereas the conventional Class E converter has a large input inductance. The main contribution of this paper is to propose the resonant switching cell as an analytic model that simplifies the analysis and the design of the resonant dc–dc converters. Furthermore, this paper presents the design method of the resonant switching cell model for minimizing the resonant current magnitude and conduction loss while the converter maintains ZVS property. The experimental results from a 10-MHz GaN-based prototype demonstrate the feasibility and effectiveness of the analysis and design based on the proposed resonant switching cell model. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM PUBLISHER]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

Provides instructions and guidelines to prospective authors who wish to submit manuscripts. [ABSTRACT FROM AUTHOR]

In the paper by Patra et al., a single-inductor multiple-output switcher was presented to produce buck, boost, and inverted outputs simultaneously. Unfortunately, this study showed some unexpected mistakes, especially in state-space equations and in the calculation of output voltages. The objective of this note was to provide correct analysis and rectify the errors in this paper. Some tables and equations have been modified that were present in the initial draft of this paper. The obtained parameters in this work could be an effective supplement and extension for the original work in the paper by Patra et al. [ABSTRACT FROM AUTHOR]

The series bridge converter (SBC) is a modular multilevel converter (MMC) recently developed to enhance power density in high-voltage high-power applications. The MMC is a well-established solution, widely researched, and exploited in practical HVdc connections, thanks to its high power quality and high efficiency. However, the main limitation of the MMC is the relatively large energy storage, also due to the fact that power ripples in the submodule capacitors include a component at the fundamental ac frequency. As a result, volume becomes critical in applications such as offshore or city center in-feeds, where space is restricted and expensive. The SBC offers a more compact footprint by exploiting a series connection on the dc side and by operating the submodules with rectified waveforms, thus moving the minimum component of the instantaneous power to twice the ac fundamental and reducing capacitors size. The drawback of the converter is a more complex energy control compared to the MMC. This paper proposes the first experimental validation of the SBC, using a 2-kW laboratory-scale prototype. Since the basic converter design has been discussed in previous papers, the focus of this paper is on converter control design and experimental validation. [ABSTRACT FROM AUTHOR]

This paper investigates the operation of the back-to-back neutral point clamped (BTBNPC) converters when the ac voltages on both ends are asynchronous. The zero-sequence injection (ZSI) technique has been used to extend the linear modulation range of the pulsewidth modulation operation. This paper investigates the ZSI of the BTBNPC to maximize the dc-bus voltage utilization while the ac voltages of both ends have different magnitudes and phases. This study further explores the reactive current injection to reduce the risk of overmodulation when grid voltages surge. The combination of these techniques can extend the operation range of the BTBNPC over varying ac voltages of both ends with the available dc-bus voltage. In addition, the issue of the neutral-point balance is also taken into consideration. Laboratory test results are provided to verify the proposed technique. [ABSTRACT FROM AUTHOR]

Four-level hybrid-clamped inverter is a newly proposed topology that can operate under a wide voltage range without switches connected in series. However, when it is applied in medium voltage high power conversions, the flying capacitors in each phase will occupy a huge volume and a high switching frequency is required to restrain the voltage ripples. In order to overcome this drawback, a four-level active neutral-point clamped inverter is discussed in this paper, which consists of only six switches and no diodes or flying capacitors are required. In order to balance the neutral-point voltages under the full power factor and modulation index range, a capacitor voltage balance method based on carrier-overlapped pulsewidth modulation is proposed in this paper. The upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection and the central dc-link capacitor voltage is balanced by adjusting the duty cycles of switching signals slightly. Simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

First harmonic analysis (FHA) is arguably the most widely used analytical technique for wireless power transfer (WPT) circuits due to its simplicity. Although FHA can provide closed-form solutions, the existence of rectifier diode forward voltage drop and higher order harmonics, especially the second and third harmonics at variable duty cycle operation, can significantly deteriorate its accuracy. This paper presents an accurate and efficient method called enhanced multiple harmonic analysis (eMHA) for the optimal design and optimal control of WPT systems. The eMHA method considers the nature of nonlinear rectification networks under nonsinusoidal current and reexamines the concept of the equivalent load. As a result, the rectified WPT system is transformed into a series of linear systems with complex load impedances. The steady-state electric quantities can be then explicitly calculated. This enables eMHA to seamlessly work with numerical optimization algorithms to facilitate the automated design and optimization of WPT systems. An example of optimal design and optimal control of a 10 W WPT system is demonstrated. The results obtained by eMHA and FHA are also compared. A prototype of the designed circuit was constructed. The accuracy and effectiveness of eMHA are verified by experimental measurements. This paper is accompanied by a MATLAB-based analytical tool with a graphical user interface demonstrating the effects of circuit variables on electrical quantities and waveforms. [ABSTRACT FROM AUTHOR]

A new single stage three-phase ac–dc converter with four switches and galvanic isolation is proposed in this paper. The new converter is simple and uses fewer switches than previously proposed ac–dc converters of the same type. It is a bridgeless converter that can operate with continuous input current and with any pulsewidth modulated method suitable for a standard three-phase six-switch voltage source rectifier. In this paper, the operation, control, analysis, and design of the proposed converter are explained and its features are discussed. Experimental results obtained from a prototype that confirm the feasibility of the converter are presented as well. [ABSTRACT FROM AUTHOR]

This paper is concerned with control-oriented modeling of a class of wireless power transfer systems with a phase-shift-controlled inverter. Two methods are investigated: the analytical modeling method, which is based on physical laws, and the refined instrumental variable method, which is based on sampled data. It shows that the former provides physical insights into the system, and that the resulting models will be accurate if the true circuit component parameters are a priori known. Otherwise, the model accuracy may decline. By contrast, the latter provides a cheap solution for accurate modeling, based only on a set of sampled input–output data, and the resulting model can capture very well the dynamic behavior of the system within a defined operating range. In real applications, it is always hard to know the actual circuit component parameters, since they may drift from the nominal values, due to some reasons such as the aging of circuit components and the variation of coil placement, making the analytical modeling method not very accurate. Therefore, to preserve the virtues of both methods, it is suggested to use them as a combination, that is, using the analytical modeling method to determine the model structure while using the data-driven modeling method to estimate the model parameters. All results derived in this paper are verified by means of both numerical simulation and experimental validation. [ABSTRACT FROM AUTHOR]

With the increasing of switching frequency in pulsewidth modulated motor system, common mode current (CMC) seriously affects the reliable operation of motor system and it has become a problem that cannot be ignored. This paper proposes a mathematical model of CMC and conducts detailed time–frequency characteristics analysis of CMC. The influence of several key parameters of motor system, such as distributed capacitance, dc bus voltage, and inverter switching frequency, on CMC characteristics has been analyzed in detail, and the corresponding variation rule of CMC oscillation amplitude and attenuation period/time has been summarized. The experimental results are presented to verify the correctness of theoretical analysis. The conclusions of this paper can lay theoretical foundation for the effective suppression of CMC in various practical applications. [ABSTRACT FROM AUTHOR]