Search

State-of-health (SOH) estimation is necessary for lithium ion batteries due to ineluctable battery ageing. Existing SOH estimation methods mainly focus on voltage characteristics without considering temperature variation in the process of health degradation. In this article, we propose a novel SOH estimation method based on battery surface temperature. The differential temperature curves during constant charging are analyzed and found to be strongly related to SOH. Part of the differential temperature curves in a voltage range is adopted to establish a relationship with SOH using support vector regression. The influence of battery discrepancy, voltage range, and sampling step are systematically discussed and the best combination of voltage range and sampling step is determined using leave-one-out validation. The proposed method is then validated and compared with an incremental capacity analysis (ICA)-based SOH estimation method using the Oxford and NASA datasets, which were collected from different cells under different conditions, respectively. The results show that the proposed method is capable of estimating SOH with the root-mean-square error less than 3.62% and 2.49%, respectively. In addition, the proposed method can improve the overall SOH estimation accuracy and robustness by combining with the ICA-based method with little computational burden. [ABSTRACT FROM AUTHOR]

In electric vehicles, a battery management system highly relies on the measured current, voltage, and temperature to accurately estimate state of charge (SOC) and state of health. Thus, the normal operation of current, voltage, and temperature sensors is of great importance to protect batteries from running outside their safe operating area. In this paper, a simple and effective model-based sensor fault diagnosis scheme is developed to detect and isolate the fault of a current or voltage sensor for a series-connected lithium-ion battery pack. The difference between the true SOC and estimated SOC of each cell in the pack is defined as a residual to determine the occurrence of the fault. The true SOC is calculated by the coulomb counting method and the estimated SOC is obtained by the recursive least squares and unscented Kalman filter joint estimation method. In addition, the difference between the capacity used in SOC estimation and the estimated capacity based on the ratio of the accumulated charge to the SOC difference at two nonadjacent sampling times can also be defined as a residual for fault diagnosis. The temperature sensor which is assumed to be fault-free is used to distinguish the fault of a current or voltage sensor from the fault of a battery cell. Then, the faulty current or voltage sensor can be isolated by comparing the residual and the predefined threshold of each cell in the pack. The experimental and simulation results validate the effectiveness of the proposed sensor fault diagnosis scheme. [ABSTRACT FROM AUTHOR]

An accurate battery capacity and state estimation method is one of the most significant and difficult techniques to ensure efficient and safe operation of the batteries for electric vehicles (EVs). Since capacity and state of charge (SoC) are strongly correlated, the SoC is hardly to be accurately estimated without knowing accurate battery capacity. Thus, a multiscale dual H infinity filter (HIF) has been proposed to estimate battery SoC and capacity in real time with dual timescales in response to slow-varying battery parameters and fast-varying battery state. The proposed method is first evaluated and verified using off-line experimental data and then compared with the single/multiscale dual Kalman filters (KFs). The results show that the proposed multiscale dual HIFs has better robustness and higher estimation accuracy than the single/multiscale dual KFs. To further validate the feasibility of the proposed method for EV applications, a lithium-ion battery-in-the-loop approach is applied to verify the stability and accuracy of the SoC estimation, and it is found that the SoC estimated from the proposed method can converge to the reference value gradually and be stabilized within 2%. [ABSTRACT FROM PUBLISHER]

A novel nine-level inverter topology for low-voltage applications is proposed in this paper. Each phase of the inverter is composed of a T-type three‐level cell and an active neutral point clamp three‐level cell. The operation principles and current conduction paths are analyzed in detail and phase-disposition sinusoidal pulsewidth modulation is used to balance voltages of flying capacitors and neutral point. The mathematical relationship between the capacitance and the desired ripple in the inverter output is established to select the intermediate capacitance value. Compared with other nine-level inverters suitable for low-voltage applications, the proposed inverter has advantages in a number of gate drivers, a number of dc sources, and efficiency. Simulation and experimental results under different settings of modulation index, power factor, output frequency, and load are presented to verify the effectiveness and performances of the proposed inverter. [ABSTRACT FROM AUTHOR]

An adaptive H infinity filter approach is proposed to estimate the multistates including state of charge (SOC) and state of energy (SOE) for a lithium-ion battery pack. In the proposed approach, the covariance matching technique is used to adaptively update the covariance of system and observation noises and the recursive least square method is used to identify the battery model parameters in real time. The hardware-in-the-loop (HIL) platform for battery charge/discharge is set up to evaluate the accuracy and robustness of the SOC and the SOE estimation and compare the proposed approach with the multistate estimators using an extended Kalman filter and an H infinity filter. The experimental results indicate that the adaptive H infinity filter-based estimator is able to estimate the battery states in real time with the highest accuracy among the three filters. [ABSTRACT FROM AUTHOR]