Search

The multiterminal dc (MTDC) grid plays an important role in large-scale power transmission and renewable energy integration owing to its excellent performance. However, there are still some problems existing in the MTDC grid, such as difficult fault current interruption and current flow control, which impedes its development. Currently, the mentioned two problems can be separately solved by hybrid dc circuit breaker (HCB) and current flow controller (CFC). However, when configured separately, they are expensive and have large footprints. Therefore, this article proposes a multiport hybrid dc circuit breaker (MHCB) with current flow control capability. The HCBs near the same dc bus are first integrated into a single MHCB and then novel CFCs are embedded into the MHCB to replace the load commutation switches. Compared with the existing MHCBs, the proposed topology shows advantages in the aspects of implementation cost, power loss, and operation speed. The operation principle is analyzed and the basis for parameter design is given in detail. The effectiveness of the proposed topology is verified by extensive simulations and experiments. Besides, the proposed MHCB is compared with the existing solutions. [ABSTRACT FROM AUTHOR]

Modular multilevel converter (MMC) has become one of the most favored topologies in medium-voltage and high-voltage (HV) applications. However, it still suffers from some drawbacks, including a lot of sizeable capacitors, high conduction losses, and no dc-fault ride-through capability. To circumvent these issues, this article presents a modified MMC, namely hybrid-leg MMC (HL-MMC). HL-MMC integrates a pair of three-phase line-frequency commutated HV voltage source converters (VSC) to replace up to 40% MMC submodules (SMs), leading to lower cost and conduction losses. Due to the ripple energy cancellation in the three-phase HV VSCs, the total energy storage requirement in HL-MMC could be also reduced, leading to up to 30% energy storage capacitance reduction compared with MMC. In addition, by combing the dc hybrid circuit breaker, the HV VSCs in the proposed HL-MMC also help provides the dc fault blocking capability, enabling a dc-fault tolerant HL-MMC without using the full-bridge (FB) MMC SMs. Therefore, a significant device and loss saving can be attained compared with the traditional MMC with FB SMs. The detailed converter operational analysis, control method, high-voltage direct current simulation model, and scale-down prototype are provided to validate the effectiveness of proposed topology. [ABSTRACT FROM AUTHOR]

It has been widely accepted to apply dc circuit breakers (DCCBs) to protect dc grids. Nevertheless, existing DCCBs have one or more following limitations: insulation recovery scheme of mechanical switch, additional precharge power supply, high conduction loss, unreliable current-breaking process, and unidirectional design. In this letter, a new DCCB with low conduction loss, simple precharging scheme, and reliable breaking ability is proposed. The proposed DCCB could break both fault and operating current actively with the same simple operation sequences. Moreover, bidirectional topology possessing all advantages mentioned previously is also presented. Topology introduction, parameters designing, and scaled-down experiment of the proposed DCCB are all presented in the letter. [ABSTRACT FROM AUTHOR]

The diode bridge submodule (SM) is one of the basic units of a hybrid high-voltage dc circuit breaker. This article works on the low inductance design of a single SM and series SMs. For the layout design of a single SM, this article proposes a simple and clear +-shaped SM layout, the low inductance design is simplified to the optimization of two laminated busbars with a simple structure. Based on the +-shaped SM layout, this article further proposes an SM structure with holes in diodes region, the stray inductance is further reduced, and only one integrated laminated busbar is needed in a single SM. For the layout design of series SMs, this article makes full use of the layout of a single SM and the mutual inductances between the SMs, series SMs are alternately connected in reverse. The single SM layout proposed in this article is effective in reducing the stray inductance. The loop stray inductance in stage II reduced from 148.4 to 72.3 nH, a 51.3% reduction. When the two parallel IGBTs turn off a 6 kA fault current in 2 μs, the voltage spike is reduced from 786.1 to 423.4 V, a 46.1% reduction. And the stray inductance difference of the bidirectional current path is controlled to about 10 nH. The layout of series SMs proposed in this article is effective in reducing the length of the series SMs, the length is reduced by 16.7%. The experimental results show that the SMs layout proposed in this article is effective. [ABSTRACT FROM AUTHOR]

In recent years, dc distribution grids have become increasingly popular because of the interest in the diffusion of distributed renewable energy. In this scenario, dc distribution grids are also favored because of the increased use of batteries and power electronic loads. The main limit to the spread of dc grids is their protection devices, which still present several problems. At present, protection devices are represented by traditional mechanical breakers or static electronic components. The first, which interrupt dc currents, have good reliability but need maintenance and have long intervention periods. In contrast, electronic switches are fast and reliable, but they reduce the efficiency because of their voltage drop. In this scenario, some hybrid breakers have been proposed to obtain the advantages of both devices. The previous solutions of hybrid breakers still suffer several critical issues and, usually, are not capable of protecting a system from short circuits without significantly reducing their lifetime. In this paper, a new low-voltage hybrid circuit breaker topology is proposed. The procedure to dimension all of the active and passive components in the device is analyzed, and the effectiveness of the proposed solution is proven by means of experimental results obtained using a prototype. [ABSTRACT FROM AUTHOR]