Search

Battery fault diagnosis is crucial for stable, reliable, and safe operation of electric vehicles, especially the thermal runaway early warning. Developing methods for early failure detection and reducing safety risks from failing high energy lithium-ion batteries has become a major challenge for industry. In this article, a real-time early fault diagnosis scheme for lithium-ion batteries is proposed. By applying both the discrete Fréchet distance and local outlier factor to the voltage and temperature data of the battery cell/module that measured in real time, the battery cell that will have thermal runaway is detected before thermal runaway happens. Compared with the widely used single parameter based diagnosis approach, the proposed one considerably improve the reliability of the fault diagnosis and reduce the false diagnosis rate. The effectiveness of the proposed method is validated with the operational data from electric vehicles with/without thermal runaway in daily use. [ABSTRACT FROM AUTHOR]

To achieve an individual and continuous power distribution for multireceiver wireless power transfer (WPT) systems, a novel multifrequency modulation method has been proposed. In the proposed method, a look-up table and delta-sigma modulation scheme are introduced to generate a mixed-frequency driving voltage pulse by synthesizing it from the given voltage pulses. The components of synthesized driving voltage pulse have continuously and individually varying amplitudes of multiple specific frequencies. With the proposed modulation method, only a standard full-bridge inverter is employed in the transmitting side to achieve power distribution among receivers, leading to a simple configuration of the transmitting source. Moreover, the proposed method has a small calculation burden and can be easily extended to the system with more receivers. When compared with the existing multifrequency modulation method, a lower switching frequency is obtained in the proposed method. Finally, the effectiveness of the proposed modulation method is verified theoretically and experimentally. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) in high-voltage dc applications usually adopt a distributed control architecture to manage a large number of submodules (SMs) through a communication network. The communication congestion and network disconnection might lead to communication interruption (CI) and eventually cause the system to malfunction. In this article, a resilient operation strategy is proposed and studied to ride-through the CI fault, in order to prevent frequent fault SM bypassing, replacement, or even system shutdown. The analysis of the MMC distributed control system with the presence of CI indicates that the insertion index of the faulted SM might become constant, which distorts the output current and results in overvoltage of the communication interrupted SM (CI-SM). The CI-SM capacitor voltage prediction can be used to determine the MMC safe operation period after CI occurs. During the safe operation period, the CI-SM power balance is sustained by utilizing prestored phase signals to generate a sinusoidal insertion index according to its capacitor voltage tracking error. Two operation modes are proposed and analyzed to ensure the MMC stable operation under various conditions. The system protection is sensibly used only if the CI duration exceeds a safe operation period, which avoids frequent SM cut-off. Good agreement of the CI-SM capacitor voltage is achieved between the theoretical and simulation results. The effectiveness and robustness of the proposed MMC resilient operation are experimentally confirmed. [ABSTRACT FROM AUTHOR]

This article proposes a circulating current and second harmonic current (SHC) suppression method by introducing virtual impedance into the circulating current and output current feedback control loops of the dc solid-state transformer (DCSST). The virtual impedance is employed to adjust impedance in the circulating current feedback control loop to decrease the circulating current when the transmission efficiency of each dual active bridge is different. And a SHC suppression method, which introduces the virtual impedance containing a bandpass filter, is adopted to reduce the SHC and improve the dynamic performance of the DCSST. Moreover, a relatively independent modular control method, which is conducive to the modular expansion of the DCSST, is proposed. Compared with traditional DCSST control methods, the proposed method can simultaneously realize the output current sharing and effectively reduce the SHC with modular control. Finally, a DCSST prototype is built and the results of the experiment verify the validity and effectiveness of the proposed control strategy and solutions. [ABSTRACT FROM AUTHOR]

This article presents a novel reduced order average model for dual-active-bridge converter which can be applied to all modulation methods, such as single-phase-shift modulation, dual-phase-shift modulation, extended-phase-shift modulation and triple-phase-shift modulation. This model considers conduction, inductance, and transformer power losses. Furthermore, the input–output filters are suitable for system performance analysis. Based on the large-signal average model, the small-signal model and the output transfer function are derived. The detailed model for predicting the large-signal transient is established and the small signal analysis in frequency domain is carried out. This model can accurately predict the steady-state and transient-state response of the system. The experimental results agreed well with the simulation results which proved the accuracy and correctness of the model. [ABSTRACT FROM AUTHOR]

The droop control is an advantageous approach for stand-alone supply systems consisting of multiple batteries, allowing among various inverters without intercommunication. The droop coefficients of batteries always vary with their state-of-charge (SoC) and charge/discharge mode, resulting in small-signal instability. Nevertheless, the existing impedance-based approaches can only assess the droop coefficients stability point, but not the stability region. Therefore, this article proposes a droop coefficients stability region analysis approach. First, the charge/discharge SoC-based droop controlled battery, the P&Q controlled distributed generator and the constant power load are separately discussed. Meanwhile, the state matrix and return-ratio matrix are established, respectively. Furthermore, the novel forbidden region criterion based on the return-ratio matrix is constructed, which reduces conservatism compared with norm-based impedance criteria and partial forbidden region criteria. Such a forbidden region criterion is first switched to the Hurwitz identification problem regarding the equivalent return-ratio matrix. Combined the state matrix and the equivalent return-ratio matrix, the generalized incidence matrix is constructed to simultaneously identify subsystem stability and interactive stability. Based on the generalized incidence matrix, an adaptive step search strategy is proposed to obtain the droop coefficients coordinated stability region. Finally, the simulation and experimental results illustrate the validity of the proposed method. [ABSTRACT FROM AUTHOR]

In this article, a novel bidirectional dc–dc converter (BDC) consisting of an active switched-inductor (A-SL) cell, a zero current ripple cell and an auxiliary capacitor cell is proposed for the battery energy storage system. The proposed BDC integrates with the advantages of high voltage conversion ratio, low power switch voltage stresses, zero ripple current on the low voltage side (LVS), and constant potential difference between the grounds of LVS and high voltage side. Thanks to the use of synchronous rectification technology, the efficiency of the proposed BDC is increased. The operating principles, the characteristics analysis and the parameter design of the proposed BDC are given. In addition, to show the merits of the proposed BDC, a comparison study involves the proposed converter and other BDCs is demonstrated. Finally, some experimental results obtained using a 1000 W prototype are presented to valid the effectiveness of the proposed BDC. 96.43% and 96.67% maximum conversion efficiencies can be achieved in the step-up and step-down modes, respectively. [ABSTRACT FROM AUTHOR]

A novel single-phase pulsewidth modulation (PWM) direct ac–ac converter based on two-level nondifferential dual-buck ac chopper legs with inverting and noninverting operations is first proposed in this article. It has the ability to resolve both voltage sag and swell problems at the same time when used as distributed flexible voltage conditioner. Compared to the traditional ac–ac converter, it has much enhanced system reliability thanks to no shoot-through problems even when all switches of each ac chopper legs are turned on, and therefore, the PWM dead time is not needed leading to improve the utilization of the duty cycles. Only half of the switches in the proposed converter is switched at high frequency during a switching period at most, which significantly reduces the total switching loss. In particularly, the converter has two greatest advantages that it retains the common sharing ground of the input and output and has the same buck/boost operation process for noninverting and inverting modes. In order to fully testify the performance of the proposed converter, a 500-W experimental prototype is built and tested at different conditions. [ABSTRACT FROM AUTHOR]

In hybrid ac/dc microgrids, a bus converter system involving the use of a high-frequency dc transformer (DCT) plays a vital role to transmit power between dc and ac subgrids. However, the multiple control tasks and power transfer mode switching of bidirectional dc/ac converter create big challenges for the systematic controller design of DCT. To address this concern, a comprehensive coordinated frequency control (CCFC) is put forward in this article for the symmetrical CLLC-DCT to adapt the complicated hybrid ac/dc microgrid operation. By establishing the mathematical model on the voltage conversion gain (VCG) and active power transmission ratio (APTR), four operation modes are proposed based on power transfer conditions. The corresponding operators are derived based on the circuit feature to avoid the redundant manipulations. Frequency threshold is determined to avoid both overvoltage and low-voltage issues based on the known allowable range of VCG. The proposed CCFC scheme is detailedly realized by combining both the open-loop and closed-loop schemes to facilitate the design procedure. The prototype DCT demonstrates the proposed CCFC scheme can achieve a peak efficiency of 98.2% and satisfied performances on both VCG and APTR. [ABSTRACT FROM AUTHOR]

The multilevel boost converter (MBC) has been widely adopted in the dc microgrid systems due to its high voltage gain and simple structure. In recent years, the power electronic loads, which usually behave as constant power loads (CPLs), are penetrating in microgrids. The incremental negative impedance of CPLs degrades the stability of microgrid systems. To ensure effective power flow and guarantee system stability, eliminating the undesired effects of CPLs is a necessity. In this article, a novel assorted nonlinear stabilizer, which is integrated with an extended nonlinear disturbance observer (NDO) and an adaptive backstepping controller, is proposed for stabilizing the MBC-fed microgrid system with CPLs. First, the reduced-order MBC model is transformed into the Brunovsky's canonical form using the exact feedback linearization technique. Second, owing to the NDO, fast system dynamic responses are achieved. Using the estimations of NDO, an adaptive backstepping controller is developed to strictly guarantee the microgrid bus voltage stability in the sense of a large signal. Simulation and experiment results are presented to verify the effectiveness and feasibility of the proposed stabilizer. [ABSTRACT FROM AUTHOR]

A virtual synchronous generator (VSG) control based on adaptive virtual inertia is proposed to improve dynamic frequency regulation of microgrid. When the system frequency deviates from the nominal steady-state value, the adaptive inertia control can exhibit a large inertia to slow the dynamic process and, thus, improve frequency nadir. And when the system frequency starts to return, a small inertia is shaped to accelerate system dynamics with a quick transient process. As a result, this flexible inertia property combines the merits of large inertia and small inertia, which contributes to the improvement of dynamic frequency response. The stability of the proposed algorithm is proved by Lyapunov stability theory, and the guidelines on the key control parameters are provided. Finally, both hardware-in-the-loop and experimental results demonstrate the effectiveness of the proposed control algorithm. [ABSTRACT FROM AUTHOR]

This paper introduces a novel H-bridge structured ac–ac pulsewidth modulation (PWM) converter topology based on two-level non-differential ac chopper legs, which can work at the non-inverting and inverting modes for the utility voltage compensation. Compared to the traditional bipolar-type H-bridge ac–ac converter, no bidirectional switches are switched in a complementary manner to overcome the commutation problem due to the delayed response of electronic circuits and semiconductor switching devices. The detailed PWM control signals and operational principles are presented to regulate the output voltage in a bipolar manner. Especially the main advantage is that the proposed ac–ac converter has the same buck/boost operation process for non-inverting and inverting modes, which ensures the continuously average current supply to the low-voltage output side without a high-value capacitor to support power. Additionally, due to the common sharing ground of the input and output, the feature that output can reverse or maintain phase angle with input is supported well. Then, the detailed analysis, design conditions, and experimental verification based on a 1 kW experimental prototype are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a modulation reference compensation method to completely eliminate the intercoupling between the output active and reactive powers of modular multilevel converters (MMCs). Different from the existing methods, it is realized not based on an accurate control model, but by directly amending the initial arm modulation references of MMCs. Therefore, the proposed method is essentially a compensation algorithm, which is extremely easy to implement in a microcontroller with low calculation burden. In addition, it does not need any additional closed-loop controllers or voltage/current sensors, which is very beneficial to practical projects. The proposed method finally realizes accurate and fully decoupled active and reactive power regulation, avoids overload operation and protection malfunction, and significantly improves the dynamic performance of MMCs. The effectiveness and accuracy of the proposed analysis and compensation method are carefully verified by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

The existing power decoupling control method of modular multilevel converter (MMC) was developed from that of conventional two-level voltage source converters. Therefore, it cannot fully realize power decoupling due to neglecting the coupling effects from submodule capacitor voltage, dc current, circulating current as well as control strategies of circulating current, which inevitably results in inaccurate regulation of active and reactive power, deteriorated system dynamic performance, possible overload operation and eventually threatens the safety and stability of MMC. This paper analyzes the intercoupling among all electrical quantities and corresponding control strategies in MMC. An accurate control model of active and reactive power/current with four coupling paths and influence factors in the rotating frame is also established. A full power decoupling control method has been proposed based on the developed model. The proposed control method can realize accurate and completely decoupled active and reactive power regulation, avoid overload operation, and significantly improve the dynamic performance of MMC. Moreover, it facilitates the parameters selection of MMC controller with no extra cost, which is of great significance for practical projects. The effectiveness and accuracy of the proposed analysis and control methods were verified by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

Modularity and high reliability from redundancy are the two attractive advantages of modular multilevel converters (MMCs). This paper elaborates a switch open-circuit fault diagnosis and a fault-tolerant operation scheme for MMCs with distributed control. The proposed fault diagnosis and fault-tolerant control method can significantly improve the reliability of the MMC while maintaining the modularity of its software implementation. By distributing fault diagnosis into submodules, its local controller is capable of identifying the switching devices in open-circuit fault without extra hardware circuitry. Based on the real-time measurements of submodule terminal voltage and arm current, single, or multiple faulty switches can be identified within 3.5 ms without triggering faulty alarms. Furthermore, a new fault-tolerant operation is proposed to maintain the output current, internal dynamics, and switching harmonics unchanged after the faulty submodule is bypassed. This is achieved by resetting the period and phase registers in the local controller according to the information of bypassed submodules. The control loops of the MMC are not influenced by the proposed fault diagnosis and fault-tolerant operation, making the operation transition seamless and reliable. Experimental results show that fault identification and system reconfiguration can be completed within 5 ms, and the MMC can seamlessly and smooth ride through the switch open-circuit faults without severe malfunction and catastrophic damages. [ABSTRACT FROM AUTHOR]

Power allocation in hybrid energy storage systems (HESSs) is an important issue for dc microgrids. In this paper, an integral droop (ID), inspired by the electrical characteristics of capacitor charging/discharging process, is proposed and applied to a cluster of energy storages (ESs) with high ramp rates. Through the coordination of the ID and conventional V-P droop, the transient power allocation in HESSs can be intrinsically realized in a decentralized manner. The high-frequency components of power demand can be compensated by the ESs with ID, whereas the ESs with V-P droop respond to the smooth change of load power. Additionally, the ID coefficient can be designed according to the nominal ramp rate of the ESs with slow response, which helps to extend the lifespan of the HESS. On the other hand, to easily assess the stability of the system feeding constant power loads, a minimum relative impedance criterion (MRIC) is developed. Based on MRIC, it is revealed that the proposed ID can shape the output impedance of the HESS and stabilize the entire system. The feasibility and effectiveness of ID are verified by both simulations and experimental results. [ABSTRACT FROM PUBLISHER]

Conventional centralized control strategies may reduce the flexibility and expandability of a modular multilevel converter (MMC) system. To tackle this issue, this paper proposes a distributed control architecture that is capable of assigning certain control tasks to distributed local controllers and improves the modularity of an MMC system. A central controller dealing with the output current regulation based on sensed arm currents is adopted. The control of MMC internal dynamics and the pulsewidth modulation (PWM) generation are distributed into local controllers. Unlike the conventional MMC control that needs all submodule capacitor voltages for capacitor voltage averaging, the proposed capacitor voltage control only relies on local submodule voltage measurement. Consequently, communication-intensive capacitor voltage transmission in each control cycle is not required and the communication burden of the control system can be significantly reduced. The control loops and possible control conflicts among submodules are presented and considered for system stability analysis. The effectiveness of the proposed distributed control architecture and capacitor voltage control for an MMC are confirmed by the start-up, steady state, and transient experimental results. [ABSTRACT FROM PUBLISHER]

The dc offset and scaling errors in the voltage and current measurements cause the injection of undesired dc and unbalanced currents into the three-phase input currents and subsequently lead to voltage ripple at the dc output voltage of the ac/dc converter. This paper proposes a compensation scheme for current measurement error where the dc offset and scaling errors in the current measurement are estimated from the voltage ripple characteristics of the dc output voltage ripple combining with simple band-pass and low-pass filters. Meanwhile, the dc offset and scaling errors in the voltage measurement can be rejected by using an advanced current controller developed with a proportional resonant plus a repetitive controller designed in the synchronous (d–q) reference frame. The proposed control algorithm is able to effectively reject the impact of both voltage and current measurement error so that the three-phase input currents are regulated to be balanced and sinusoidal with ultralow dc current component. Meanwhile, the dc output voltage is also well regulated to be pure dc with a negligibly small voltage ripple. The proposed compensation method is developed without the need of extra hardware circuit, sensor, or precise information of system parameters so that it can be considered as more cost effective and robust solution. The effectiveness of the proposed solution is verified by experimental results. [ABSTRACT FROM AUTHOR]

The traditional finite-control-set model predictive control (FCS-MPC) method for a cascaded H-bridge (CHB) rectifier has two main issues: heavy computational burden and low steady-state current performance. In this paper, a novel FCS-MPC method has been proposed for a single-phase CHB rectifier. The proposed method solves the optimization problem of FCS-MPC for one cell by one cell, like a “pipeline.” In the proposed method, the sampling period is divided into equal intervals by the number of cells. At the beginning of the first interval, the first cell selects its switching state to be applied. Then, the following cell selects its switching state to be applied at the beginning of next interval. Finally, the selected switching state of last cell will be applied at the beginning of the last interval. A cost function presenting the control objectives of common source current error and itself dc-link voltage error is evaluated for each cell. A single-phase three-cell CHB rectifier controlled by a DSpace DS1104 is tested and the experimental results show that a significant reduction in computational time, an improved steady-state current performance, and a comparable dynamic response are achieved in the proposed method in comparison with the traditional FCS-MPC method. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) are multi-input multi-output (MIMO) nonlinear systems. The control systems for MMCs are required to simultaneously achieve multiple control objectives, e.g., output current regulation, submodule capacitor voltage control, and circulating ripple currents suppression. Existing cascaded control strategies for MMCs achieve those control objectives with relatively complex controllers, and the controller parameter design is normally difficult for such nonlinear systems with highly coupled states. In view of this, a feedback linearization-based current control strategy is proposed for an MMC system in this paper. The nonlinear state function model of the MMC is presented and transformed to a linearized and decoupled form with the help of the input–output feedback linearization technique. Based on the linearized system, simple linear controllers are employed to regulate the output and inner differential currents of the MMC, which significantly reduces the difficulty in controller design. The stability of the proposed control strategy is analyzed. The experimental verification results show that, compared to the conventional cascaded control strategies for MMCs, the proposed feedback linearization control strategy is able to achieve improved steady-state and dynamic performances. The robustness of the proposed control strategy against parametric uncertainties is experimentally investigated. [ABSTRACT FROM PUBLISHER]

Unidirectional inductive power transfer systems allow loads to consume power, while bidirectional inductive power transfer (BIPT) systems are more suitable for loads requiring two-way power flow such as vehicle to grid applications with electric vehicles. Many attempts have been made to improve the performance of BIPT systems. In a typical BIPT system, the output power is controlled using the pickup converter phase shift angle, while the primary converter regulates the input current. This paper proposes an optimized phase-shift modulation strategy to minimize the coil losses of a series–series compensated BIPT system. In addition, a comprehensive study on the impact of power converters on the overall efficiency of the system is also presented. A closed-loop controller is proposed to optimize the overall efficiency of the BIPT system. Theoretical results are presented in comparison to both simulations and measurements of a 0.5 kW prototype to show the benefits of the proposed concept. Results convincingly demonstrate the applicability of the proposed system offering high efficiency over a wide range of output power. [ABSTRACT FROM AUTHOR]

Indirect matrix converter (IMC) is an alternative for ac/ac energy conversion, usually operated with a voltage stepped-down gain of only 0.866. For applications like distribution generation where voltage-boost functionality is required, the traditional style of operating the IMC is therefore not appropriate. Like most power converters, the operation of the IMC can surely be reversed to produce a boosted gain, but so far its relevant control principles have not been discussed. These challenges are now addressed in this paper with distributed generation suggested as a potential application. Simulation and experimental results for validating various performance aspects of the proposed control schemes can be found in a later section of this paper. [ABSTRACT FROM AUTHOR]

In this paper, a modified one-cycle-control (OCC) scheme is proposed for regulating three-phase pulsewidth-modulated (PWM) rectifiers operating under unbalanced and distorted supply conditions. Mathematical analysis is first presented to show the dominant harmonic-voltage components appearing across the dc link of the PWM rectifier when it is controlled by an existing OCC scheme. Such dc-link harmonics when produced may aggravate harmonic currents flowing into the input terminals of the three-phase rectifier. To address these interrelated unbalance and harmonic concerns, the concept of reconstructing the appropriate reference signals in the OCC control core is introduced, before modifications are recommended for altering the key control equation. The improved OCC controller eventually developed is proven to exhibit minimal input-current distortion and a smoother dc-link voltage without using large capacitance. Other advantages exhibited by the traditional OCC scheme, such as no phase-locked loop, no frame transformation, and constant switching frequency, are also retained by the improved controller, whose theoretical findings are fully verified by experimental results obtained from a 1.2-kW three-phase PWM rectifier built in the laboratory. [ABSTRACT FROM PUBLISHER]