Search

This paper proposes a d–q cross-coupling current controller for permanent magnet synchronous motor (PMSM) drives. Slotting and cross-coupling effects in PMSMs cause the effective air-gap length to vary with the rotor angle and distort the distribution of the air-gap flux. Such distortions have a significant influence on the current control by changing the relationship between the stator currents and voltages. To investigate their effects, a d–q model is established in this paper, which is suitable for describing the voltage characteristics of the actual PMSMs. The model contains the angle-dependent parameters, the cross-coupling inductance between d–q axes, and the q-axis permanent magnet flux linkage, unlike the ideal d–q model. The transfer function matrix from the d–q currents to d–q voltages of PMSM is newly derived from the model. Based on that, the current controller with the feedback and feedforward terms of 2-by-2 matrix is proposed. It is designed so that the independent gains are in low-pass filter forms and the coupling control gains are zero with eliminating interference between d–q axes. The proposed controller contributes to providing the stable control performance by canceling the slotting and cross-coupling effects. The performance of the proposed current controller is verified by experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a dc-flux-injection method for fault diagnosis of high-resistance connection (HRC) in a direct-torque-controlled permanent magnet synchronous machine (PMSM) drive system. In this method, the flux linkage bias is superimposed in the flux control loop of the direct torque control system, and then the dc current offset is excited in the stator windings. By superimposing two different pairs of flux linkage biases, a binary linear equation group about the resistance deviations can be established based on the stator currents and zero-sequence voltage component. By solving the equation group, the resistance deviations can be calculated for the HRC fault detection, faulty phase location, and fault severity estimation. Both the simulation and experimental results validate the effectiveness of the proposed method. In addition, the proposed method is immune to the symmetrical variations of stator resistance and interturn fault of the PMSM. [ABSTRACT FROM AUTHOR]

Hybrid-excitation switched reluctance motors (HESRMs) have attracted considerable attention for various drive applications due to their simple structure, low cost, and high-torque/power capabilities. This paper comprehensively evaluates and compares a high-torque segmented-stator HESRM drive with a conventional SRM drive in terms of static magnetic and dynamic performances. The stator of the segmented HESRM consists of six individual U-shaped segments; each one has two teeth associated with a permanent magnet (PM) installed between them. The static magnetic characteristics of a segmented HESRM and a conventional SRM, including flux distribution, phase flux linkage, electromagnetic torque, are analyzed and compared. The total fluxes created by the PM and by the excited current are strongly coupled. The details of mathematical model as well as dynamic performances of the segmented HESRM is derived and compared with the conventional SRM. Finally, a segmented HESRM and a conventional SRM of the same size are prototyped for experimental verification. From the comparative study, it is indicated that the segmented HESRM has better characteristics than the conventional SRM, such as less iron consumption, higher static and dynamic average torque production, lower torque ripple, higher power and torque densities, higher efficiency, and stronger starting capability. The measured results of static magnetic characteristic, steady-state and transient performances, and torque–speed characteristic of two SRM drives verify the finite-element analysis, modeling, and corresponding predictions. [ABSTRACT FROM PUBLISHER]

This paper presents a comprehensive evaluation of several direct torque control (DTC) strategies for permanent magnet synchronous machines (PMSMs), namely DTC, model predictive DTC, and duty ratio modulated DTC. Moreover, field-oriented control is also included in this study. The aforementioned control strategies are reviewed and their control performances are analyzed and compared. The comparison is carried out through simulation, finite-element analysis, and experimental results of a PMSM fed by a two-level voltage source inverter. With the intent to fully reveal the advantages and disadvantages of each control strategy, critical evaluation has been conducted on the basis of several criteria: Torque ripple, stator flux ripple, switching frequency of inverter, steady-state control performance, dynamic response, machine losses, parameter sensitivity, algorithm complexity, and stator current total harmonic distortion. [ABSTRACT FROM PUBLISHER]

Multireference frame based asymmetric six-phase interior permanent magnet motor modeling and control strategy under single open-phase fault are investigated in this article. The motor modeling under healthy operation is firstly established based on a dual dq-axis synchronous rotating frame. With this dual dq-axis frame, the motor modeling considering the magnetic saturation effect under open-phase fault has been derived. By introducing a dual-direction rotating frame, the stator current under single open-phase fault can be treated as the sum of a positive current sequence and a negative current sequence. With this dual-direction rotating frame, the two current sequences can be transformed into two dc components for fault-tolerant operation. Fault-tolerant control schemes with maximum torque per ampere for copper loss minimization and torque maximization are developed, respectively. Finally, the validity of the proposed modeling and control are evaluated by experiments under both steady and transient scenarios. [ABSTRACT FROM AUTHOR]

When multiphase drives are used for specific applications, the modular solutions are preferred as they use consolidated power electronics technologies. The literature reports two modeling approaches for multiphase machines having a modular configuration of the stator winding. The first approach is the vector space decomposition (VSD) that models the energy conversion as for an equivalent three-phase machine. The main alternative to the VSD is the multistator (MS) modeling that emphasizes machine modularity in terms of torque production. Both approaches have advantages and disadvantages for multiphase machines with a modular structure. Therefore, this article aims to combine the VSD and MS approaches, defining a new matrix transformation and, hence, developing a new modeling approach for multiphase machines with a modular structure. The proposed transformation allows a decoupled and independent torque control of the sets composing the machine, preserving the torque regulation's modularity. Together with a new vector control scheme, it has been applied to a modular permanent magnet synchronous machine (PMSM) with a nonstandard spatial shift between windings. Experimental results are presented for a nine-phase PMSM prototype with a triple-three-phase stator winding configuration. [ABSTRACT FROM AUTHOR]