Search

Semiconductor opening switch (SOS) diodes are capable to switch currents with a density of more than 1 kA/cm 2 and withstand nanosecond pulses with an amplitude of up to 1 MV. SOS diodes, however, require a specific pumping circuit that must simultaneously provide forward and reverse pumping currents with a time of ∼ 500 and ∼ 100 ns, respectively. Such a pumping circuit with energies > 1 J typically requires a gas-discharge switch or a low-efficient solid-state solution. This study proposes a novel approach to pumping SOS diodes based on a spiral generator (SG) (also known as a vector inversion generator). Due to its wave characteristics, the SG produces a bipolar current discharge that meets the time duration and current amplitude required to pump an SOS diode. Moreover, the initial pulse from the spiral typically has a relatively low current amplitude compared to the opposite polarity secondary pulse, so the SOS diode can operate at very high efficiencies. This idea has been tested using an all-solid-state SG coupled with large-area SOS diodes (1 cm 2 ). With this combination, a voltage pulse of 62 kV having a rise time of only 11 ns was obtained on an open circuit load (3 pF, 1 M Ω ). The experiments were highly repeatable, with no damage to the components despite multiple tests. There is significant scope to further improve the results, with simple alterations to the SG.

This article presents an experimental arrangement which, using 3-D numerical modeling, aims to study biomedical effects using subnanosecond pulsed electric fields (PEFs). As part of a major effort into developing contactless technology, the final aim of this study is to determine conditions of the applied PEFs (number of pulses, strength, pulse repetition frequency) able to produce electropermeabilization. The arrangement uses a pulsed power generator producing voltage impulses with an amplitude of up to 20 kV on a 50- $\Omega $ matched load, with a rise time of 100 ps and a duration of 600 ps. During the preliminary study reported here, samples containing E. Coli were exposed to PEFs in a 4-mm standard electroporation cuvette, allowing the application of a peak electric field strength of up to 60 kV/cm. The studies were facilitated by detailed 3-D electromagnetic modeling of the electric field distribution generated by voltage impulses inside the system. Due to the nature of tests, the numerical analysis played an essential role in the interpretation of results. Preliminary biological results reported in this study are very encouraging, showing that trains of 5000 to 50 000 pulses applied at a pulsed repetition frequency of 200 Hz (maximum PRF) can efficiently induce E. Coli electropermeabilization.

The electrode erosion and lifetime performance of a compact and repetitively triggered field distortion spark gap switch were studied at a repetitive frequency rate of 30 Hz, a peak current of 8.5 kA, and a working voltage of ±35 kV when the switch was filled with a gas mixture of 30% SF6 and 70% N2 at a pressure of 0.3 MPa. The variations of the time-delay jitter and the self-breakdown voltage were both studied for the whole service lifetime of the spark gap switch. The morphology of both the electrodes and the plate insulator, before and after the service lifetime tests, is also analyzed. The results show that during these tests, the time-delay jitter is basically synchronized with the self-breakdown voltage jitter, and both undergo firstly a process of rapidly decreasing their values, then remaining stable, and finally and gradually increasing after 70 000 pulses. The change in the electrode surface roughness (i.e., surface profile) is caused by erosion and chemical deposits in the switch cavity, which are mainly the two factors that affect the time-delay jitter of the switch. Tip protrusions on the electrode surface, due to electrode erosion, contribute to reducing the time-delay jitter. However, due to chemical reactions, fluorides and sulfides are deposited on the switch components, as well as metal particles caused by electrode erosion sputtering. Slowly, after a large number of shots, all these phenomena affect the self-breakdown performance resulting in an increased self-breakdown voltage jitter, which also causes the time-delay jitter to increase. Although there are a number of reasons that contribute to the deterioration of the performance of the switch, it is fortunate that if a switch suffering a degraded performance is reassembled, with the electrodes mechanically polished and all the components cleaned, the optimal performance of the switch can be restored. If maintenance work is carried out regularly to preserve the condition of the switch’s inner components, the service lifetime of the switch can be prolonged.

This work was stimulated by the assumption that for a gas-filled spark gap closing switch operating at a high repetition frequency, there is an optimal frequency range in which the time-delay jitter reaches a minimum value. The experiments to test this assumption use an electrically triggered, field-distortion spark gap filled with the SF6/N2 gas mixture. The results show that indeed, the time-delay jitter decreases for a range of frequencies for which the filling gas can substantially restore the interelectrode insulation before increasing at a higher operation frequency. The experimental results demonstrate the correctness of the abovepresented assumption: the time-delay jitter of the field-distortion spark gap has its minimum when the unit operates in the repetition frequency range between 20 and 30 Hz. Since the recovery time depends on the gas species and the gap distance, the optimum operation frequency range should also vary depending on the spark-gap distance and the filling gas properties.

This paper describes the development of a small field-distortion spark gap switch. Comprehensive experimental studies made with the switch revealed its self-breakdown characteristics, voltage operating range, time delay and jitter, repetition frequency, and finally the electrode erosion processes and duration of its service lifetime. A series of design improvements were required to be implemented in the switch design. For example, to reduce the structural inductance of the switch and to improve its working characteristics, the main electrode was designed as a circular track structure. Similarly, to increase the operation stability and reduce the self-breakdown probability, the trigger electrode was designed as a disk-like structure. Moreover, to balance the gas pressure in the discharge region and increase the stability during closure, a circular hole was added at the center of the trigger electrode. The compact switch has a small size of only 150 mm $\times42$ mm, a weight of 1.5 kg, and can be successfully operated at a voltage over 110 kV, at a repetition rate between 1 and 50 Hz and having a jitter of less than 4 ns. It was experimentally demonstrated that during normal operation conditions, the switch lifetime exceeds 100 000 shots.

International audience; This paper introduces the work undertaken to reliably use off-the-shelf differentiating voltage probes attached to coaxial transmission lines. The results obtained prove that indeed such probes are a valid and simple instrument for measuring nanosecond and subnanosecond voltage impulses. As a bonus, this paper also highlighted an important challenging phenomenon that appears whenever an attempt is made to measure fast voltage impulses with a differentiating probe positioned too close to the closing switch of a pulse forming line generator. \textcopyright 1973-2012 IEEE.

International audience; The temperature dependence of the Kerr constant for water has been determined over the range 19 °C-45 °C at a wavelength of 658 nm. This paper presents the experimental arrangement used for this purpose and the data obtained, for which a polynomial fit is provided. A formula is also suggested to help estimate the variation of the Kerr constant for water with both temperature and wavelength. \textcopyright 2016 IEEE.

A repetitive 0.6 MV, 10 GW Tesla-driven Blumlein pulsed power generator, with an overall energy efficiency in excess of 90%, has been designed, manufactured and demonstrated by the Pulsed Power Group at Loughborough University. The paper describes the application of various numerical techniques used to design a successful generator, such as filamentary modelling and electrostatic and transient circuit analysis. All the major parameters of both the Tesla transformer and the Blumlein pulse forming line were determined, enabling accurate modelling of the overall unit to be performed. The wide bandwidth embedded sensors used to monitor the dynamic characteristics of the overall system are also presented. Experimental results obtained during this major experimental program are compared with theoretical predict ions and the way ahead towards generating faster output voltage impulses is considered.

This paper provides an overview of the response of the tuned secondary circuit of a Tesla transformer, following impulse excitation from the tuned primary circuit. Multiorder oscillatory voltages and currents are energized in the secondary circuit, and research is ongoing to determine the fundamental and higher order modes for various secondary winding configurations, with the aim of developing design techniques that can be used to suppress the generation of the higher order modes. It is anticipated that this will lead to generators which exhibit enhanced spectral purity and which will be better suited to use in electronic warfare applications than conventionally wound Tesla transformers.

This paper is devoted to a detailed presentation of all aspects involved in the development and demonstration of a compact electric field measuring system using the Kerr effect in water. During the experimental program, the Kerr constant of water was determined as 2.45 ·10-14 m/V2 ±10% at a wavelength of 658 nm, standard pressure and temperature, and fast pulsed electric field strength of up to 360 kV/cm. Details are given of the experimental arrangements and the techniques used at both research centers involved. Finally, a brief comment on the way ahead is provided.

A joint program involving the study and practical performance of a foil-flyer electromagnetic accelerator has recently been initiated by Atomic Weapons Establishment, Aldermaston, and Loughborough University. As an initial phase of the work, both 0-D and 2-D numerical models for the foil-flyer accelerator have been developed. The 0-D model, although very crude, is capable of providing an insight into the accelerator phenomena and is currently used for parametric design studies. The 2-D model is based on the well-proven Loughborough filamentary modeling technique and is capable of accurately calculating the 2-D distribution of current, velocity, acceleration, and temperature of the flyer, together with the complete distribution of the magnetic and electric fields generated during a shot. The paper presents the two models and compares typical theoretical predictions with the corresponding experimental results.