Search

Voltage induced in the dc winding by the armature field in wound field switched flux (WFSF) machines will induce voltage perturbation in the voltage supply and cause dc winding current ripple and field excitation fluctuation. This will challenge the dc voltage controller and deteriorate the control performance, especially when the load and/or the rotor speed are high. In this article, the dual three-phase armature winding design with a phase-shift of 30 electrical degrees is employed in the partitioned stator WFSF machines to reduce the on-load dc winding-induced voltage. Analytical deductions and finite element (FE) results demonstrate that the dominant sixth-order-induced voltage harmonic can be suppressed to zero. Hence, the peak-to-peak induced voltage in the 12/11- and 12/13-pole partitioned stator WFSF machines can be reduced by 83.35% and 82.53%, respectively. Due to the improvement of winding factors, the torque densities are 4.85% and 5.60% higher, respectively. Prototypes are built and tested to verify the analytical and FE results. [ABSTRACT FROM AUTHOR]

In this article, we propose a novel switching-table-based direct torque control (ST-DTC) method to eliminate the current harmonics in dual-three-phase permanent-magnet synchronous machines due to the back electromotive force (back EMF) harmonics and voltage vector selection. By employing a novel space voltage vector selection strategy and the optimal action time for different groups of vectors, a novel ST-DTC method is developed. Furthermore, in order to implement standard pulsewidth modulation (PWM) switching sequence, a centralization PWM method for 36 voltage vectors is introduced. The proposed method can effectively reduce the phase current harmonics caused by both back EMF distortion and voltage vector selection, and still reserve the advantages of the conventional ST-DTC, such as fast torque response and simple structure. Its effectiveness is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

In this article, a current profiling technique is proposed for the torque density enhancement in switched reluctance machines (SRMs). The novel current profile is initially developed from the harmonic current injection method and is then modified into a unipolar waveform to allow the application of an asymmetric bridge inverter. It is found that, neglecting the magnetic saturation, the optimal current profile for the maximum torque per ampere operation in an SRM is close to a pulse with high-order harmonics. However, an optimized current with relatively low-order harmonics can provide better performance in the practical situation. Based on the analytical and the finite element results, the proposed method is proved to be able to enhance the torque density by 20% at the light load condition and by 15% at the rated condition compared with the conventional SRM excitation. Also, the large torque ripple and core loss in SRMs are suppressed and the efficiency is improved. More importantly, unlike many other current profiling techniques, the proposed current profile has fixed parameters and is easily adaptable to different machine specifications. The effectiveness of the proposed method is verified by both the finite-element analyses and the experiments. [ABSTRACT FROM AUTHOR]

In this article, the flux reversal permanent magnet (FRPM) machine with toroidal windings is presented and analyzed with reference to conventional concentrated windings. First, the influence of rotor pole numbers on FRPM machines with conventional concentrated windings is investigated. It is found that although the 12/13 stator slot/rotor pole FRPM machine has a high back electromotive force, the pitch factor, and magnet flux utilization ratio of concentrated windings are very low. By adopting toroidal windings instead of concentrated windings in the 12/13 FRPM machine, the pitch factor and resulted machine performance can be effectively improved. Finite-element analysis shows that the 12/13 FRPM machine with toroidal windings can produce 79% higher torque than its counterpart with concentrated windings. Then, the critical design parameters and detailed electromagnetic performance of FRPM machines with both winding types are analyzed and compared. It is shown that the machine with toroidal windings has higher torque, efficiency, power factor, and lower torque ripple, making it particularly suitable for low-speed, high-torque, and axial length limited applications. In addition, other feasible stator slot/rotor pole combinations to use toroidal winding are identified, with the aid of equivalent pole-pair number. Finally, two 12/13 FRPM prototypes with toroidal windings and concentrated windings are tested to validate the analyses. [ABSTRACT FROM AUTHOR]

This paper proposes a consequent-pole flux reversal machine (CP-FRM) with biased flux modulation theory, which employs homopolar permanent magnets (PMs) placed between the adjacent stator poles. The machine topology is introduced from the perspective of FRM with a shifted magnet position and CP arrangement, and the performance comparison between the proposed CP-FRM and its original surface-mounted PM (SPM) counterpart is presented to highlight the torque improvement of the CP structure. Then, a simplified permeance model is applied to the CP-FRM to identify the principal effective air-gap field harmonics engaging in the torque productions. It shows that the CP-FRM works based on a biased flux modulation effect due to its asymmetric air-gap field distribution caused by the CP configuration, which unveils its underlying torque improvement mechanism over its SPM-FRM counterpart. In order to obtain the highest torque capability, the key design parameters are analytically optimized by analyzing the winding configuration, which aids the establishment of a general design guideline for the CP-FRM. The analytical and FE results are validated by experiments. [ABSTRACT FROM AUTHOR]

In this paper, the open-circuit dc-winding-induced voltage in a wound field switched flux (WFSFs) machines is analyzed. The phenomenon of open-circuit dc-winding-induced voltage is illustrated and the mechanism is explained. Rotor skewing is proposed to reduce the open-circuit dc-winding-induced voltage, and the optimal skewing angle is analytically derived based on the analytically deduced harmonic orders of the open-circuit dc-winding-induced voltage. Finite-element (FE) analyses show that the open-circuit dc-winding-induced voltages in the analyzed 12-stator-pole partitioned stator WFSF machines having 10-, 11-, 13-, and 14-rotor-pole rotors can be effectively reduced by >94%, while the ac-winding phase-fundamental back-EMFs can be maintained by >95%. Twelve/ten-stator/rotor-pole prototypes with skewed and nonskewed rotors are built and tested to verify the analytical and FE results. [ABSTRACT FROM AUTHOR]

A partitioned stator hybrid excited machine is proposed, in which the permanent magnets and field windings are alternately placed on an inner stator separated from the outer stator having armature windings. This machine inherits the features of brushless machines and benefits from better space utilization. The operating principle and the effects of slot/pole combinations are investigated in detail. Further, based on 2-D finite-element analysis, the electromagnetic performances of the proposed machines, including back-electromotive force, cogging torque, flux regulation range, torque capability, power factor and torque–speed curve, are evaluated. The results reveal that the proposed machines can exhibit wide flux regulation range as well as good torque density. The prototype is manufactured and tested to validate the predictions. [ABSTRACT FROM PUBLISHER]

In switched-flux permanent-magnet machines, winding coil connections can be rearranged into several types of machine winding configurations (MWCs), such as all poles wound, alternate poles wound, and single and dual three-phase windings. This paper investigates the influence of machine saliency on a sensorless control operation based on different MWCs. First, by injecting an HF carrier signal, the machine saliency level can be evaluated experimentally. The influence of saliency on an HF-signal-injection-based sensorless operation for different MWCs can be then investigated irrespective of any information of machine parameters. However, the secondary saliency caused by magnetic saturation or current harmonics may exist in a machine, due to which the sensorless control performance will deteriorate. Hence, an orthogonal signal-based position tracking observer is proposed to improve the accuracy of rotor position estimation rather than utilizing an existing position observer. Furthermore, experimental results confirm that a prototype machine exhibits different saliency characteristics and apparent saliency, in which the HF-injection-based sensorless control technique can be applied. Moreover, better steady and dynamic state performance can be achieved by the improved position estimator compared with using an existing position observer. [ABSTRACT FROM AUTHOR]

Due to the fixed and limited sampling period in the real-time system, three-phase permanent-magnet synchronous machine (PMSM) drives using switching-table-based direct torque control (ST-DTC) usually suffer from steady-state error and ripple of torque. For the case of the dual three-phase system that has been widely investigated recently, the harmonic currents inevitably occur, which can be regarded as the third issue. This harmonic currents lead to the increase of losses and the decrease of system efficiency. Previous literature has addressed the aforementioned issues but only deals with either the torque ripple issues or harmonic currents. Therefore, this paper first introduces two types of synthetic vectors, which can reduce the harmonic currents effectively, as well as the most suitable switching sequences. Then, a modified five-level torque regulator has been proposed to improve the torque performance. With the proposed method, not only the harmonic currents have been suppressed, but also the steady-state error and ripple of torque can be considerably reduced, whereas the merits of classical ST-DTC, such as simple structure and excellent dynamic performance, are preserved. The experimental results validate the effectiveness of the proposed strategy. [ABSTRACT FROM PUBLISHER]

This paper investigates the improved switching-table-based direct torque control strategies (ST-DTC) for dual three-phase permanent magnet synchronous machine drives. The classical ST-DTC scheme for dual three-phase drives is usually seriously penalized by significant current harmonics, which cause large losses and reduce the efficiency of the drive system. Hence, a modified switching table consisting of 12 new synthetic voltage vectors is proposed. With this new switching table, not only the variables relating to the torque production are well controlled, but also the variables contributing to the current harmonics are eliminated successfully within one sampling period. Furthermore, a simple modified torque regulator is proposed to reduce the torque ripple and the steady-state error of torque which is usually observed in the real-time system. The switching sequence which is most suitable for the implementation of the real-time system has been proposed to minimize the computation burden. The proposed strategy only changes the switching table and torque regulator without any major modifications, and hence, the merits of the classical direct torque control, i.e., simple structure and good robustness, are still preserved. The experimental results validate the effectiveness of the proposed strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes how to use the addition of rotor position offsets as perturbation signals for the parameter estimation of permanent-magnet synchronous machines (PMSMs), which can be used for the condition monitoring of rotor permanent magnet and stator winding. During the proposed estimation, two small position offsets are intentionally added into the drive system, and the resulting voltage variation will be recorded for the estimation of rotor flux linkage. With the aid from estimated rotor flux linkage, the stator winding resistance can be subsequently estimated at steady state. This method is experimentally verified on two prototype PMSMs (150 W and 3 kW, respectively) and shows good performance in monitoring the variation of rotor flux linkage and winding resistance. [ABSTRACT FROM PUBLISHER]

This paper proposes a multiparameter estimation scheme for permanent-magnet (PM) synchronous machines (PMSMs) under variable-speed control, of which the estimation model is full rank and has taken into account the estimation and compensation of voltage-source-inverter nonlinearity. During the proposed estimation, the PMSM will work under variable speed control, and two sets of machine data corresponding to two sets of different rotor speeds will be recorded and used for the calculation of the proposed estimation model. It shows that the proposed estimation model can be solved by using a conventional quantum genetic algorithm and can ensure the identifiability of all needed parameters owing to its inherent full rank feature. The performance test of the proposed estimation is then conducted on an interior PMSM, and it shows that parameters such as rotor PM flux linkage and winding resistance can be accurately estimated without the aid from nominal parameter values of PMSM. Therefore, the proposed method can be used for the condition monitoring of stator winding and rotor PMs. [ABSTRACT FROM PUBLISHER]

The conventional switching-table-based direct-torque-controlled (DTC) ac machine drive is usually afflicted by large torque ripple, as well as steady-state error of torque. The existing methods, which optimize the duty ratio of the active vector, are usually complicated and parameter dependent. Based on the analysis of instantaneous variation rates of stator flux and torque of each converter output voltage vector, a simple and effective method considering the effect of machine angular velocity is proposed to obtain the duty ratio. The experimental results carried on a dSPACE platform with a laboratory prototype of the permanent-magnet machine verify that the proposed duty-based DTC method can achieve excellent transient response, less torque ripple, and less steady-state error, without resorting to the complicated control method over a wide range of operating regions. [ABSTRACT FROM PUBLISHER]

This paper investigates the influence of nonideal voltage measurements on the parameter estimation of permanent-magnet synchronous machines (PMSMs). The influence of nonideal voltage measurements, such as the dc bus voltage drop, zero shift in the amplifier, and voltage source inverter nonlinearities, on the estimation of different machine parameters is investigated by theoretical and experimental analysis. For analysis, a model-reference-adaptive-system-based estimator is first described for the parameter estimation of the q-axis inductance, stator winding resistance, and rotor flux linkage. The estimator is then applied to a prototype surface-mounted PMSM to investigate the influence of nonideal voltage measurement on the estimation of various machine parameter values. It shows that, at low speed, the inverter nonlinearity compensation has significant influence on both the rotor flux linkage and winding resistance estimations while, at high speed, it has significant influence only on the winding resistance estimation and has negligible influence on the rotor flux linkage estimation. In addition, the inverter nonlinearity compensation will not influence the q-axis inductance estimation when it is under id = 0 control. However, the dc bus voltage drop due to the load variation and zero shift in the amplifier will significantly influence the q-axis inductance estimation. [ABSTRACT FROM PUBLISHER]