Search

This article is motivated by an interesting recent result on antilock braking system (ABS) design using two-time scale (TTS)-based estimation. In this article, the basic method of TTS is extended to estimate not only the disturbances but also their derivatives, improving the accuracy of estimation by an order of magnitude. Further, the problem of ABS is extended to an eight-DOF vehicle model to include the effects of load transfer, steering dynamics, and actuator dynamics. Since analysis showed that the use of basic TTS to ABS design results in a poor transient in the estimation error dynamics, this article proposes a new formulation of the TTS method specifically for ABS. Two new ABS-specific sliding surfaces are proposed to compensate the actuator dynamics where the second sliding surface is proposed as an improvement over the first one. The stability, and convergence of estimation, and tracking errors are analyzed. The proposed methods are validated on MATLAB/Simulink, and CarSim platforms for a D-class sedan car. The results are also validated on an experimental ABS platform in the laboratory. [ABSTRACT FROM AUTHOR]

In this article, we aim to investigate the path following control problem for four-wheel-independent-drive electric vehicles with consideration of modeling errors and complex driving scenarios. In order to guarantee operational safety and robustness, a supertwisting second-order sliding mode (SOSM) control strategy is employed to suppress the heavy chattering issue existing in the traditional sliding mode control (SMC). To degrade the lumped disturbance, a nonlinear disturbance observer (NDOB) technique is proposed to estimate the disturbance and compensate the modeling error. Then, a composite control strategy, which combines the SMC algorithm and NDOB technique is proposed based on stability analysis of the corresponding closed-loop system. Finally, hardware-in-the-loop experimental results show that the supertwisting SOSM control algorithm with the NDOB technique can achieve better tracking performance and suppress the chattering phenomenon. [ABSTRACT FROM AUTHOR]

In this article, the problem of control of antilock braking systems under significant uncertainties and unknown relationship between tire-road friction coefficient and wheel slip ratio for a two-axle vehicle model is considered. Two methods based on a disturbance observer and sliding mode control are proposed. In the first method, a conventional sliding surface is used while in the second method a new nonlinear sliding surface is proposed as an improvement over the first method. The performance under the proposed methods is assessed analytically and by MATLAB simulation under different road conditions. The proposed methods are validated further on CarSim platform. [ABSTRACT FROM AUTHOR]

This paper is concerned with the robust passive fault detection problem for switched continuous-time linear parameter-varying systems with mensurable and unmeasurable scheduling parameters. A switched Takagi–Sugeno (TS) interval observer is designed to estimate the set of admissible state values. Using multiple fuzzy input to state stability-Lyapunov function and average dwell time (ADT) concept, sufficient conditions to guarantee the convergence and the robustness of the proposed observer are obtained. These conditions are formulated as a linear matrix inequality (LMI) problem. In contrast to the existing results based on multiple Lyapunov function and ADT switching, the derived conditions lead to less conservative LMIs characterization. Subsequently, the residual intervals are generated using the designed interval observer and used directly for fault detection (FD) decision making. Finally, the proposed methodology is tested using two examples. First, an academic example is used to illustrate the obtained relaxation. Second, a nonlinear vehicle model corrupted by faults is considered. Longitudinal velocity and cornering stiffness coefficients are treated, respectively, as the measurable and unmeasurable scheduling parameters. Simulation results based on experimental data show the effectiveness of the proposed FD schema. [ABSTRACT FROM AUTHOR]

This paper addresses the development and Hardware-in-the-Loop (HiL) testing of an explicit nonlinear model predictive controller (eNMPC) for an antilock braking system (ABS) for passenger cars, actuated using an electro-hydraulic braking unit. The control structure includes a compensation strategy to guard against the performance degradation due to actuation dead times, identified by experimental tests. The eNMPC is run on an automotive rapid control prototyping unit, which shows its real-time capability with comfortable margin. A validated high-fidelity vehicle simulation model is used for the assessment of the ABS on a HiL rig equipped with the braking system hardware. The eNMPC is tested in seven emergency braking scenarios, and its performance is benchmarked against a proportional-integral-derivative (PID) controller. The eNMPC results show: 1) the control system robustness with respect to the variations in tire-road friction condition and initial vehicle speed; and 2) consistent and significant improvement of the stopping distance and wheel slip reference tracking, with respect to the vehicle with the PID ABS. [ABSTRACT FROM AUTHOR]

In this paper, a general control allocation (CA) algorithm is proposed based on a lexicographic optimization (LO) strategy for a vehicle's longitudinal and lateral control. The primary objective of this CA is to distribute the torque adjustments of the lateral controller such that the error between the desired and actual forces and moments at the vehicle's center of gravity is minimized, while maintaining the longitudinal tire slip ratios close to a desired range. Presence of various constraints in practical systems can significantly increase the complexity and effort of properly adjusting the tuning parameters in the objective function. Hence, an LO method is used to prioritize the objectives. Lateral stability of the vehicle has the highest priority and is subject to the constraint of maintaining small tire slip ratios. The second priority of CA is assigned to minimize the adjustment torques. The proposed LO-based approach reduces exhaustive vehicle testing commonly required for tuning of the separately designed controllers and the cost and time of the implementation. In addition, it makes the algorithm easily transferable from one vehicle to another by reducing the number of tuning parameters. Simulation and experimental results are presented to show the effectiveness of the proposed approach. [ABSTRACT FROM AUTHOR]