Search

The stability of dual active bridge converter (DAB) is threatened when feeding the constant power loads (CPLs). This article proposes a deep reinforcement learning-based backstepping control strategy to solve this problem. First, a nonlinear disturbance observer is adopted to estimate the large-signal nonlinear disturbance. Then, a backstepping controller is used to stabilize the voltage response of the DAB under the large-signal disturbance. Finally, a compensation method based on deep reinforcement learning is developed to intelligently minimize output voltage tracking error and improve the operating efficiency of the system. The proposed controller can guarantee system stability under the large-signal disturbance of the CPL and achieve a fast dynamic response with accurate voltage tracking; it is more adaptive by using the deep reinforcement learning technique through the learning of its neural networks. The effectiveness of the proposed controller is verified by experiments. [ABSTRACT FROM AUTHOR]

The interleave boost converter (IBC) has been used as the interface converter between the low-voltage electrical energy sources, such as lithium-ion battery banks, solar panels, and fuel cells, and the dc bus of dc microgrids. With increasing penetration of tightly regulated power electronic loads, which behave as constant power loads, the stability of microgrid dc-bus voltage that is fed by the IBC is threatened by the loads’ negative incremental impedance feature. To ensure the stability of the bus voltage, this article proposes a nonlinear disturbance observer (NDO)-based sliding-mode control algorithm. The proposed algorithm has excellent robustness, low computational burden, and no extra hardware cost. A generalized average state-space model is proposed to facilitate the control design. In addition, an NDO is employed to estimate the output power of IBC rapidly and accurately. To verify the effectiveness of the proposed algorithm, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

Different from single-bus dc microgrids (MGs), a multibus MG normally bridge multiple dc buses via a complex line impedance network. This intricate configuration together with tickling constant power loads may cause severe stability issues. For system stability improvement, conventional ways include designing small-signal stabilizers in a decentralized way and constructing large-signal stabilizers by solving Lyapunov equation in a central controller. Note that centralized methods may be vulnerable to single point of failures, while decentralized patterns are commended to reinforce MG reliability and scalability. To implement large-signal stabilization in decentralized mechanisms, which has rarely been investigated in the existing literature, a novel uniform nonsmooth control scheme (UNCS) is proposed, in this article. UNCS has the following fourfold advantages. First, UNCS helps to express commonly used dc/dc converters, boost, buck, and buck–boost, into a uniform model. The model substantially facilitates a uniform stabilizer design that accommodates the preceding three converters despite their differences in topology. Second, UNCS assigns each converter based distributed generator (DG) with a composite large-signal stabilizer comprising a nonsmooth observer and a nonsmooth controller. The controller neutralizes the disturbances estimated by the observer, and it also rigorously stabilizes the internal states in DG uniform model. Third, the stabilizer also provides an additional control degree of freedom, a finetuning factor, to refine DG dynamic responses to meet high requirements for voltage and power qualities. Fourth, when numerous DGs with the proposed stabilizer congregate to build a multibus MG, the overall system large-signal stabilization is autonomously attained without communication links, which is mathematically justified by Lyapunov stability analyses. As such, DGs are allowed to randomly plug in/out without worrying about impairing system level stability. Simulations help to properly select relevant key parameters. Experiments show that UNCS outperforms the standardly designed PI controls, and it will stabilize the multibus MG in a large operation range. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) generators have continuously increased in recent years, whose power is usually controlled through the perturbation and observation (P&O) method. In essence, the P&O method is nonlinear and discontinuous. Hence, the conventional small-signal stability analysis is not suitable anymore when the influence of the P&O-based power control is considered. Focusing on this problem, this paper adopts the nonlinear describing function (DF) method to conduct the accurate stability analysis of PV generators with consideration of P&O-based power control. The detailed procedures about the DF method are introduced, and then the related influence factors like perturbation size, filters, and so on are analyzed quantitatively. Furthermore, the comparison with the conventional stability analysis methods is made, which suggests that the DF method can effectively enhance the accuracy of the stability analysis. All the conclusions are verified by the real-time hardware-in-loop tests. [ABSTRACT FROM AUTHOR]

Direct modulation principle is widely used in modular multilevel converters (MMCs) for its simplicity and natural stability. However, it results in strong active and reactive power coupling. This paper carefully analyzes and identifies four power coupling paths and two power influence factors with the direct modulation principle. Full power decoupling of the MMC can be realized by cutting off the derived coupling paths and compensating the influence factors. However, this will further deteriorate the already poor damping of the MMC and significantly increase dc-bus current fluctuations. To solve this problem, the sources resulting in poor damping are identified and then a new closed-loop dc-bus current controller is incorporated into the control system. Finally, the proposed power decoupling strategy with the newly designed current controller realizes completely decoupled power regulation, avoids overload operation, and obviously improves the dynamic performance of the MMC. Furthermore, it increases the stability of the MMC system under all possible operation conditions. The proposed control strategy is confirmed by experimental results. [ABSTRACT FROM AUTHOR]

To improve the interception performance in missile guidance applications, this paper proposes a novel control strategy for the integrated guidance and control design subject to input constraints. The system constraints are translated into a restriction in an invariant set, which is then enforced by manipulating the derivative of the applied reference. For the integrated system in the presence of disturbances and parametric uncertainties, disturbance observers are applied to estimate the lumped disturbances existing in each loop. The quadratic stability via dynamic surface control is guaranteed, and an ellipsoidal approximation of the invariant set is obtained, which can be enlarged to allow some degree of the input saturation. The effectiveness of the proposed scheme is illustrated using numerical simulations against a maneuvering target. [ABSTRACT FROM AUTHOR]

Repetitive control strategies have been commonly applied in pulse-width-modulated (PWM) voltage source inverters (VSIs) for many industrial applications. This paper presents a repetitive controller for voltage harmonic mitigation of VSI-based islanded microgrids. The phase delay in the overall control system, e.g., the delay caused by the digital duty cycle calculation, PWM generation, and repetitive controller, has to be compensated by elaborately designed phase lead filters in order to prevent control performance deterioration and system instability. Nevertheless, quantificational analysis and practical design of the time advance unit in such filters are hardly found in existing literature works. In view of this, this paper proposes an explicit analysis of the phase lead filters and a novel design method of the time advance unit in repetitive controllers to ensure system stability. Moreover, with the help of the proposed method, the overall system stability margin is predictable and improved controller performance is achieved as well. The proposed method is implemented experimentally to show the accurate stability margin calculation as well as the excellent steady state and dynamic performances of the repetitive control scheme. [ABSTRACT FROM PUBLISHER]