Search

Direct modulation principle is widely used in modular multilevel converters (MMCs) for its simplicity and natural stability. However, it results in strong active and reactive power coupling. This paper carefully analyzes and identifies four power coupling paths and two power influence factors with the direct modulation principle. Full power decoupling of the MMC can be realized by cutting off the derived coupling paths and compensating the influence factors. However, this will further deteriorate the already poor damping of the MMC and significantly increase dc-bus current fluctuations. To solve this problem, the sources resulting in poor damping are identified and then a new closed-loop dc-bus current controller is incorporated into the control system. Finally, the proposed power decoupling strategy with the newly designed current controller realizes completely decoupled power regulation, avoids overload operation, and obviously improves the dynamic performance of the MMC. Furthermore, it increases the stability of the MMC system under all possible operation conditions. The proposed control strategy is confirmed by experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual-input matrix converter (DIMC) to integrate two three-phase ac type energy resources to a power grid. The proposed matrix converter is developed based on the traditional indirect matrix converter under reverse power flow operation mode, but with its six-switch voltage source converter replaced by a nine-switch configuration. With the additional three switches, the proposed DIMC can provide six input terminals, which make it possible to integrate two independent ac sources into a single grid-tied power electronics interface. The proposed converter has input-to-output voltage boost capability since power flows from the converter's voltage source side to its current source side. Commanded currents can be extracted from the two input sources to the grid. The proposed control and modulation schemes guarantee sinusoidal input and output waveforms as well as unity input power factors. The simulation and experimental results using a laboratory prototype are provided to validate the effectiveness of the proposed control and modulation schemes for the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper presents a novel matrix converter with one ac input and two ac outputs. The presented topology is based on the traditional indirect matrix converter, but with its rear-end six-switch inverter replaced by a compact nine-switch inverter. With only three extra switches added, the proposed converter can produce two sets of three-phase ac outputs, whose amplitudes, frequencies, and phases can appropriately be regulated. Features such as sinusoidal input and outputs, unity input power factor and minimum commutation count are all retained by the proposed topology, despite having an additional output. Its modulation is realized by the computationally less intensive carrier-based method, whose unique carrier requirements can easily be managed within a programmable logic device. Mathematical proof for validating sinusoidal input and outputs achieved by this modulation technique is also discussed, before being verified in simulation and experimentally, together with other findings. [ABSTRACT FROM AUTHOR]

High penetration of renewable energies through fast-response power converters results in a considerable displacement of conventional synchronous generators and losing of system inertia for frequency control. Modular multilevel converters (MMCs) can be employed serving as an interface between the large-scale renewable generation and power grids. In a microgrid with high shares of renewables integrating through MMCs, submodule (SM) capacitors can be used as energy storage to provide a degree of synthetic inertia for system frequency support. This paper quantitatively exploits the MMC synthetic inertia in a microgrid with flexible renewable penetration levels. An MMC inertia coefficient concept is proposed. It is mainly affected by the penetration ratio, the SM capacitance, and the modulation index of an MMC, with the system operation constraints. According to the analysis, a substantial portion of system inertia can be provided by properly designed MMCs. Detailed MMC frequency control loops are presented. The capacitor average voltage is proportionally linked to the frequency deviation, in order to flexibly adjust the capacitor energy during frequency events. The MMC output active power is deliberately and simultaneously regulated according to the capacitor energy change rate. By controlling the MMC capacitor voltage, dc side power, and output active power, an amount of energy can be released or absorbed by SM capacitors to improve the system frequency response during the frequency event transients, while the renewable generation is scarcely influenced. The proposed concept is experimentally verified and the results show that, with proper system parameters and control loops, the line frequency deviation and the rate of change of frequency can be significantly reduced. Good agreements of the system frequency characteristics have been achieved between the theoretical calculation and experimental results. [ABSTRACT FROM AUTHOR]

The digital control system of modular multilevel converters (MMCs) normally synchronizes with the switching actions. The switching frequency of an MMC is generally selected as low as possible from an efficiency point of view, which leads to an unavoidable and relatively long time delay in the control system. Such a time delay might deteriorate the MMC performance and even reduce the stability margin by introducing infinite uncertain eigenvalues into the system state functions. Without a proper time-delay model and quantitative system stability analyses, MMCs might suffer from uncertainties and unstable risks during their operations, especially when the switching frequency is low. This paper derives an MMC model considering the time delay in the digital control system. A Padé-based stability analysis method is then proposed, which consists of three steps: information integration and critical eigenvalue extraction, and trajectory visualization and critical angle (CA) calculation, and quantitative assessment and extreme value determination. By the proposed model and method, the critical eigenvalue can be effectively extracted. With the Hopf bifurcation, the time delay in the digital control system induces a pair critical conjugate eigenvalues into MMC systems, which is detected as an instability cause. The CA and the critical impact are defined to quantitatively assess the stability, while selecting the controller parameters and minimum switching frequency. The proposed method for the MMC stability assessment is experimentally verified. [ABSTRACT FROM AUTHOR]