Search

Hybrid DC circuit breakers (HDCCBs) have excellent performance in terms of breaking speed and low losses and have become the mainstream technology for dc fault isolation in dc grids. However, because of the breaking limitation of the solid-state branch in HdcCBs, the existing HdcCBs are still weak in breaking high current. Although the breaking ability can be improved by series and parallel devices, the cost will increase rapidly, and it is very difficult to share current by paralleling a single type of device. This article proposes a novel HdcCB topology that combines two types of power electronic devices in solid-state branches to meet the requirement of a large breaking capacity in dc grids. The structure and breaking principles of this novel topology, which aims to break high current, are introduced. The design methods of the key parameters are presented. Then, the current breaking ability of the novel topology is verified by developing a prototype completing a 10 kV/60 kA breaking test in 3 ms. Finally, this novel topology is compared with other dc circuit breakers at the same breaking level, which shows that this novel topology has obvious advantages in cost and volume with fewer devices. [ABSTRACT FROM AUTHOR]

The hybrid dc circuit breaker (HDCCB) is one of the most promising solutions for the dc interruption. But the power electronics-based load commutation switch (LCS) in the main current path causes the high on-state loss and cost, which inhibits the application of the HDCCB. In this paper, a novel hybrid dc circuit breaker is proposed, in which the vacuum interrupter with the external transverse magnetic field (ETMF) is designed to improve the arc voltage and thus enhance the current commutation to power electronics. The ETMF-based vacuum interrupter achieves the fast current commutation instead of the LCS, which realizes the low on-state loss and cost while preserving the short commutation and interruption time. The arc voltage characteristic with ETMF is analyzed, and the influence of the different factors on the commutation time and di/dt before current zero are investigated in detail. Based on the calculation results, a 10 kV dc breaker prototype based on the proposed topology is developed with the breaking current of 15.5 kA. Finally, the application of the proposed scheme in HVdc grids is discussed. [ABSTRACT FROM AUTHOR]

Two key challenges in meshed multi-terminal dc (MTdc) grids are line power flow management and fault current interruption, which can be solved by current flow controllers (CFCs) and hybrid dc circuit breakers (HCBs), respectively. However, the power losses and the implementation costs of CFCs and HCBs are relatively high. In order to overcome these drawbacks, a combined HCB (CHCB) is proposed in this article by fully utilizing the core ideas of the interline dual H-bridge CFC and the HCB. The proposed device can substitute multiple HCBs at a dc bus with greatly reduced cost. In addition to the fault current interruption capability, the current flows in the adjacent lines can be controlled by the embedded multi-line CFC in the CHCB expanded from the existing interline dual H-bridge CFC. The system-level behavior of the proposed CHCB is similar to the separate solution of the typical HCB and the multi-line CFC. Extensive simulations and experiments verify the effectiveness of the proposed device. Besides, a comparison of the proposed CHCB and the separate solution is presented. [ABSTRACT FROM AUTHOR]

Extraction of the current commutation loop (CCL) inductance is necessary for the overvoltage analysis of power devices. In general, each transient process of a converter corresponds to a specific CCL. However, there is no such single CCL in the full-bridge module in hybrid dc circuit breakers during the turn-off transient. First, this article proposes a coupled inductance model of full-bridge modules. The model has less number of inductance compared to the traditional partial inductance model. Second, this article proposes the extraction method of inductances that can be easily obtained by both simulation and measurement. Moreover, the measured overvoltage waveforms of insulated gate bipolar translators (IGBTs) in the full-bridge module agree with the simulation results. Third, we propose an equivalent circuit of the series full-bridge modules in a 500 kV hybrid circuit breaker based on the proposed coupled inductance model. The mutual inductances among different modules are considered due to the compact structure of the series modules. The measured results show that the overvoltage of the IGBT in the series module could be well-predicted by the proposed equivalent circuit. [ABSTRACT FROM AUTHOR]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]