Search

In this article, we propose a novel processing algorithm for frequency-modulated continuous-wave (FMCW) ice sounding radar, which addresses the along-track focusing of internal reflecting horizons. It is a modified frequency scaling algorithm that can handle the two-layer medium imaging model as well as the Doppler impact of the motion within the sweep in a nadir-looking radar. The proposed algorithm’s comprehensive derivation and implementation processes are described. In the range-Doppler domain, a really effective formulation for radar signals is also presented, which considers refraction effects and electromagnetic wave propagation velocity changes at the interface of two different media. Point target simulations are carried out to demonstrate the algorithm’s performance. The proposed method is also tested on the real data acquired by the shallow-layer-detection ice sounding radar (SLDISR). The result shows the applicability of the proposed method for imaging the ice sheet. [ABSTRACT FROM AUTHOR]

To realize high azimuth resolution for sea-surface targets, this article proposes a superresolution imaging method that relies on the Weibull distribution. The proposed method introduces the generalized Gaussian distribution and Weibull distribution to represent the statistical distribution function of the target prior information and sea clutter, respectively. The corresponding objective function was derived under the maximum a posteriori (MAP) criterion. To address the nonlinearity of the objective function, this article adopts the Newton–Raphson iterative method to resolve it. Simulations and experimental data assessment indicate that the proposed method has superior superresolution imaging performance compared with other traditional superresolution methods for sea-surface target imaging. [ABSTRACT FROM AUTHOR]

For the target with 3-D rotation, the 3-D synthetic aperture radar (SAR) imaging is very important for the feature extraction and classification. To solve this issue, a novel 3-D imaging algorithm through the airborne SAR system with a single antenna is proposed in this article, which has great advantages for the simplification of system structure compared with the traditional interferometric system. The proposed 3-D airborne SAR imaging algorithm can be implemented with three steps: 1) the azimuth signal is modeled as multicomponent linear frequency modulation (LFM) signal due to the relative movement between the target and radar. 2) The scatterer height position can be obtained by estimating the frequency modulation rate (FMR) for the LFM signal. 3) The 3-D airborne SAR image is obtained via the range-Doppler (RD) algorithm. Furthermore, the reconstruction performance under different rotation patterns, including roll, pitch, and yaw, is analyzed. The availability of the presented novel technique is demonstrated by the results of simulated and real experimental data. [ABSTRACT FROM AUTHOR]

Multiple-input–multiple-output synthetic aperture radar (MIMO-SAR) has extensive application prospects, mainly including the acquisition of multidimensional scattering information, high-resolution and wide-width (HRWS) imaging, and moving target indication (MTI). Its echo separation is the most technical challenge, and so far, the confirmation for orthogonal waveform encoding MIMO-SAR by airborne experiments has not been reported in any literature. Here, an echo separation experiment based on the segmented phase code (SPC) waveforms and an airborne digital beamforming SAR (DBF-SAR) system is demonstrated for the first time. In the experiment, the SPC waveforms are cyclically transmitted within the adjacent pulse repetition intervals (PRIs) to simulate multiple transmitters, and the scattered echoes are received by the 16-channel antennas in elevation at the same time. In the postprocessing, the echo signals of continuous PRIs are added to obtain the mixed echoes, and a detailed echo separation method is adopted. In the method, the mixed echo signals from close arrival angles and far arrival angles are separated by the time shift and weighting, and by the bandpass filtering and DBF technique, respectively. Through the presented method, the mixed echoes of dual-transmit and 16-receive (2T16R) SAR imaging mode are separated and imaged successfully. The experimental results not only validate the echo separation scheme but also indicate that it is very promising in future MIMO-SAR missions. [ABSTRACT FROM AUTHOR]

Superresolution methods can be applied to real aperture radar (RAR) to improve its angular resolution by solving an inverse problem. However, traditional superresolution methods are achieved after batch data collection, which requires extensive operational complexity and storage space. To solve this problem for RAR, an online detect-before-reconstruct (DBR) framework is proposed in this article based on the sparse property of targets. First, along the range direction, each sample of the echo data is detected to reduce the computational complexity by reducing the dimension of the effective data. Second, along the azimuth direction, a data-adaptive online processing structure is proposed to reduce the storage requirement for the angular superresolution problem. Finally, within the online processing structure, a target data-adaptive updating strategy is proposed to reduce the number of iterations for each target grid. The online DBR-based framework can effectively reduce the operational complexity caused by the noise values of the echo data. Based on the proposed online processing structure, the storage requirement and the operational complexity of the angular superresolution for an RAR system can be greatly reduced without significant reconstruction performance loss. The results of simulations and experimental data verify the proposed framework. [ABSTRACT FROM AUTHOR]

The 3-D inverse synthetic aperture radar (ISAR) tomography is an enabling technique for applications such as the exact diagnosis of scattering mechanisms for complex targets. Nevertheless, current ISAR tomography solutions still suffer from problems such as the great computational complexity and optimal utilization of the signatures acquired from limited baselines. In this work, we propose a fast ISAR tomography technique for fully polarimetric 3-D imaging of man-made targets. A stack of 2-D complex-valued images with different baselines and polarizations is first obtained through a phase error calibration (PEC) process and graphic processing unit accelerated polarimetric filtered backprojection. A polarimetric state-space decomposition (P-SSD) algorithm is then developed which could provide joint 3-D reconstruction results with low computational complexity. Examples from both numerical multibaseline data for the Sandia laboratories implementation of cylinders (SLICY) benchmark model and the outdoor range dataset collected by the Georgia Tech Research Institute (GTRI) are presented to demonstrate the superior performance and the usefulness of the proposed technique. [ABSTRACT FROM AUTHOR]

High-resolution wide-swath synthetic aperture radar (HRWS-SAR) imaging is highly desirable since it allows one to produce high-resolution SAR images of large areas during a short visit time. In this article, staggered coprime pulse repetition frequencies synthetic aperture radar (SCopSAR) is proposed. It divides the time during which a scatterer is illuminated by the antenna beam pattern into two halves where, in each half, pulses are transmitted at the rate of one of two sub-Nyquist pulse repetition frequencies (PRFs). Such PRFs are related to the Nyquist PRF using two coprime subsampling factors. This allows extending the maximum range swath width that can be imaged by a number of times that equals the smaller subsampling factor at the expense of a reduction in the azimuth resolution by half. It further allows for a reduction in the amount of data to be stored and communicated. SCopSAR is an imaging modality suitable for scenes that contain a small number of bright scatterers over a dark background which, for instance, is the case when imaging ships in a calm sea background. Compared with the techniques recently proposed in the literature, SCopSAR simplifies the radar requirements since it uses only one carrier frequency, one waveform, and one channel. Simulations and real ERS-2 satellite raw data are used to validate the theoretical findings presented in this article. [ABSTRACT FROM AUTHOR]

Forward-looking multichannel synthetic aperture radar (FLMC-SAR) is an important tool for modern remote sensing applications, which has the capability to reconstruct the high-resolution image of the front area. However, due to the azimuth-variant characteristics of the motion errors over a long aperture, FLMC-SAR data processing is usually a challenging task, especially when involving the motion compensation (MOCO) coupled with Doppler ambiguity resolving. To accomplish an accurate MOCO for FLMC-SAR, a novel parametric azimuth-variant MOCO approach is proposed in this article. Aiming at the coupling problem of MOCO and Doppler ambiguity resolving over the full aperture, we can decouple them through the subaperture division. As a full synthetic aperture is decomposed into several subapertures, the high-order motion errors of the full aperture can be decomposed into the first-order motion errors of the subaperture. On this basis, the mismatch of the space–time spectrum caused by the motion errors can be solved by spectral estimation, yielding Doppler ambiguity resolving for each subaperture. Meanwhile, the azimuth-variant characteristic of motion errors in FLMC-SAR system is characterized by a parametric angle-dependent quadratic phase error (QPE) model. The motion parameters are estimated by a joint multichannel angle estimation-based signal quadratic decomposition method. Immediately, the MOCO for ambiguous targets with different motion errors can be processed separately to improve the imaging performance. Experimental results based on both simulated and real data demonstrate that the proposed method is suitable for FLMC-SAR system. [ABSTRACT FROM AUTHOR]

In this article, we present a novel method that incorporates the range points migration (RPM) method, $k$ -space decomposition-based accurate, and noise-robust range extraction filter for microwave or millimeter-wave (MMW) short-range radar using a considerably lower fractional bandwidth signal. The advantage for higher angular resolution in higher frequency systems, such as MMW radar, has been implemented to the incoherent-based RPM method, using the simple 1-D or 2-D Fourier transform-based processing to maintain the imaging accuracy in RPM processing for both the range and the angular directions. As an additional advantage of our method, it also offers data clustering in $k$ -space, which can enhance the imaging accuracy of the RPM method. The numerical and experimental tests demonstrated that the proposed method offers numerous advantages over the Capon-based super-resolution algorithm or coherent-based imaging approaches. [ABSTRACT FROM AUTHOR]

Most existing super-resolution imaging methods fail to work in low signal-to-noise ratio (SNR) condition due to the ill-posed antenna measurement matrix, but the sparse-truncated singular value decomposition (TSVD) method can effectively suppress noise and improve azimuth resolution in low SNR condition. However, the current sparse-TSVD method encounters large computation cost, resulting in a slow algorithm speed. In this work, a fast sparse-TSVD super-resolution imaging method of real aperture radar is proposed. First, the proposed method is based on the results of TSVD, using the truncated unitary matrix and diagonal matrix to reconstruct the signal convolution model. The dimension of the reconstructed antenna measurement matrix reduces from $N \times N$ to $k \times N$ , and the dimension of the reconstructed echo matrix reduces from $N \times 1$ to $k \times 1$ , where $N$ is azimuth sampling points and $k$ is truncation parameter, $N \gg k$. Much of the expensive matrix– multiplication computation can then be performed on the smaller matrices, thereby accelerating the algorithm. Second, an objective function is established as the ${l_{1}}$ constraint based on the regularization strategy. Lastly, this article employs iterative reweighted least square (IRLS) method to solve the objective function, and the dimension of the reversed matrix is lessened from $N \times N$ to $k \times k$ , speeding up the algorithm further. The simulation and real data verify that the proposed algorithm not only improves the azimuth resolution in low SNR condition but also increases computational efficiency compared with the sparse-TSVD method. [ABSTRACT FROM AUTHOR]

In the context of spaceborne synthetic aperture radar (SAR) imaging, high resolution and wide swath are inherently conflicting requirements. These may, however, be simultaneously satisfied by advanced imaging modes with multichannel architectures in elevation and/or azimuth. This article elaborates on a new mode based on multiple elevation beams and a simple pulse repetition interval (PRI) variation scheme which allows high-resolution wide-swath imaging. It is shown to use the illumination time more efficiently than ScanSAR and yet to be simpler than staggered SAR. Good SAR imaging performance is achieved with a rather compact antenna design. The proposed imaging mode is suitable for spaceborne SAR systems with planar and reflector antennas. In order to improve the imaging performance, a reflector antenna architecture with a multichannel feed in both elevation and azimuth is considered. [ABSTRACT FROM AUTHOR]

We address the problem of high-resolution radar imaging in low signal-to-noise ratio (SNR) environments in an approximate Bayesian inference framework. First, the probabilistic graphical model is constructed by imposing the sparsity-promoting spike-and-slab prior to the distribution of scattering centers. Then, the model parameters and phase errors are estimated iteratively by expectation propagation (EP) and maximum likelihood (ML) estimation. Compared with the available imaging methods based on the numerical optimization and Bayesian inference, the proposed method has exhibited more flexibility in data representation and better performance in parameter estimation, particularly in sparse-aperture and low SNR scenarios. [ABSTRACT FROM AUTHOR]

Forward-looking imaging and target detection are highly desirable in many military and civilian fields, such as search and rescue, sea surface surveillance, airport surveillance, and guidance. However, there is a blind zone of forward-looking imaging for conventional Doppler beam sharpening and synthetic aperture radar. Scanning radar can be utilized to obtain a real beam image of a forward-looking area and implement target detection, while its azimuth resolution is poor due to the limitation of antenna size. Besides, during the processing procedure, imaging and target detection are usually regarded as two independent parts, which means that the imaging result will directly affect the detection performance. In this article, an integrated algorithm of super-resolution imaging and target detection for forward-looking scanning radar is proposed. In this algorithm, first of all, low-rank and sparse constraints as regularization norms are incorporated into the forward-looking scanning radar imaging and the objective function is established. Subsequently, the convex theory is utilized to solve the objective function and transform the problem of simultaneous super-resolution imaging and target detection into an optimization problem. Lastly, the super-resolution imaging and the target detection results are obtained simultaneously by solving the optimization problem using the alternating direction method of multipliers. In addition, simulation and experiment results are given to verify the effectiveness of the proposed algorithm. [ABSTRACT FROM AUTHOR]

Real-aperture radar can be utilized to realize forward-looking imaging by antenna scanning the imaging region. However, low azimuth resolution seriously affects its practical application. Although traditional super-resolution methods could enhance azimuth resolution to a certain extent, effective preservation of contour information for important targets still remains to be a problem. In this article, a method of total variation-sparse (TV-sparse) multiconstraint deconvolution is proposed to improve azimuth resolution of forward-looking imaging as well as preserve contour information of important targets. Since our interested targets usually appear to be sparse, the sparse constraint of the target is introduced first to achieve high resolution of forward-looking images, which may cause the loss of target contour information in the meantime. Second, total variation (TV) constraint is introduced based on the sparse constraint, converting traditional single-constraint super-resolution problem to a multiconstraint problem. We then use the split Bregman algorithm (SBA) to solve the multiconstraint problem, whose solution is the super-resolution image of radar forward-looking region. Compared with traditional super-resolution methods, the proposed method can improve the azimuth resolution of radar forward-looking imaging as well as better restore target contour information by adjusting respective weights of sparse constraint and TV constraint. Finally, the performance of the proposed method is validated with the simulation and measured data. [ABSTRACT FROM AUTHOR]

Because of the poor performance of the conventional total variation (TV) super-resolution imaging method in low signal-to-noise ratio (SNR) condition, a TV super-resolution imaging method based on the truncated singular value decomposition (TSVD) strategy is proposed. First, based on the regularization theory, the TV function is selected as the constraint term to construct objective function. Second, to solve the problem of noise amplification faced by the conventional TV method, this article reconstructs the objective function based on the TSVD strategy, which improves the antinoise performance by discarding small singular values of antenna convolution matrix. Finally, due to the nondifferentiable property of reconstructed objective function, this article utilizes the iterative reweighted norm (IRN) method. Since the influence of the noise is weakened by the TSVD strategy, the proposed method can achieve super-resolution imaging and contour preservation in low SNR condition. The simulation and experimental results demonstrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Directional borehole radar (BR) 3-D imaging is a challenging problem due to its limited observation space within a borehole. We present a linear prediction (LP)-based direction-of-arrival (DOA) estimation and a migration-based 3-D imaging algorithm for the directional BR, which is composed of a transmitting antenna and a uniform circular array including four small receiving antennas. Only the azimuth is estimated, while the elevation and the distance are included in the imaging process. LP is a useful tool for DOA estimation in the radar domain, but a single linear array (LA) has azimuth ambiguity in DOA estimation. The four receiving antennas are treated as two orthogonal uniform LAs. The combination of two arrays removes the ambiguity in DOA estimation. In addition, the moving window and the threshold-based estimation increase the calculation efficiency. According to the estimated azimuth angles, the measured signal at each depth is decomposed to the corresponding directions. Therefore, there is a time-series signal in each direction at each depth. After processing the measured signals at all depths, we obtain a 3-D data set that can be used for horizontal- and radial vertical-section displays. Then, the radial vertical-section data are processed by migration which transforms the time domain signal into a wavefield-based 3-D image. Simulated data from a fracture model are used to validate the algorithm, and the reconstructed image can reveal the real model well. It is concluded that the novel method we propose is an effective one with real-time processing capability. [ABSTRACT FROM AUTHOR]

State-of-the-art and future spaceborne synthetic aperture radar (SAR) systems increasingly often face the requirement of providing high-resolution images with reduced revisit times, requiring coverage of wide swaths. Since these are contradicting drivers in terms of system design, different alternatives for high-resolution wide-swath SAR imaging have been investigated, relying on digital beamforming and the use of multiple receiver channels, both in elevation and azimuth dimensions. In this context, staggered SAR, which operates with a pulse repetition frequency (PRF) variation, using a single channel in azimuth proves itself as a promising alternative for covering wide continuous swaths with moderate azimuth resolution, whereas the use of multiple azimuth receiver channels bears the potential of improving the azimuth resolution over a given swath, but has yet only been applied to systems with a fixed PRF. This paper introduces and analyzes in detail processing techniques suitable for the combination of these techniques, leading to novel multichannel staggered SAR imaging modes with the potential for very fine azimuth resolution over ultra-wide swaths. A system concept with 2-m azimuth resolution over a 400-km swath in quad-pol is provided as an example. [ABSTRACT FROM AUTHOR]

Directional wave spectra and integrated wave parameters can be derived from X-band radar sea surface images. The calibration of such spectra has until now depended on various empirical and semiempirical methods, which also require an external reference increasing the total expenses of operation. A novel algorithm, which is fully based on theory, producing reasonable estimates of the significant wave height based on shadowing in the images, has been now developed. The method does not require any reference measurements, and with that, enables automatic calibration of spectra from radar sea surface images, as well as the potential for reduced operational cost and increased accuracy of such wave-monitoring systems. Promising results are obtained with data acquired at a test site in the North Sea. Further work is, however, required to refine the algorithm and to test it under varying circumstances at various sites. [ABSTRACT FROM PUBLISHER]

The most intuitive way to extract depth information from remote sensing images is stereogrammetry, in which a digital elevation model (DEM) is achieved by computing stereoscopic radar images. When only the amplitude of the radar images is considered, this computation is called radargrammetry. The main idea of which is to match stereopair radar images in order to create a disparity map from one image to the other and, finally, to compute the elevation. Therein, we present our studies on the extraction of 3-D information from radar images. We examine a way to produce a DEM of a challenging area of the French Alps. The central issue of this paper concerns improvements for radargrammetric synthetic aperture radar image processing for high-relief reconstruction, and we focus on the matching step, which is one of the most important points of the radargrammetric processing. Thus, we propose original methods using different correlation windows. On the one hand, we take the advantages of a multiwindow approach to combine relevant information by multiplying the correlation surfaces obtained for each correlation window size during the matching operation. On the other hand, the second improvement is based on the expansion of windows on foreshortened areas, particularly because of the side-looking radar view. These methods allow us to achieve reliable image matching and to improve the accuracy of the DEM. [ABSTRACT FROM AUTHOR]