Search

Enormous concerns focus on the high-power and wide bandwidth traveling-wave tube (TWT) for its outstanding performance. In this article, a shape-optimized staggered double-vane slow-wave structure (SWS) for terahertz (THz) sheet beam TWT is proposed. The shape-optimized staggered double-vane SWS takes the advantages of higher interaction impedance, lower transmission loss, and lower phase velocity than conventional staggered double-vane SWSs. The shape-optimized staggered double-vane SWS with 85 periods is designed, fabricated, and cold tested. The measured transmission loss of the shape-optimized staggered double-vane SWS is less than 0.79 dB/cm in the frequency range of 0.211–0.26 THz, which is in good agreement with the simulation results. Furthermore, the beam–wave interaction analysis of a sheet beam TWT with this SWS is given. The output power is predicted to be >100 W with 3-dB bandwidth of >50 GHz. The results show that the shape-optimized staggered double-vane SWS is a very promising scheme to construct a high-power and wideband THz TWT for future applications such as communication and imaging. [ABSTRACT FROM AUTHOR]

The angular log-periodic meander-line traveling wave tube (TWT) is a kind of low voltage, small-sized, high power, low cost, on chip amplifiers, and considered as a key part of the advanced communication systems, the future biomedical applications and the next electronic counter measure (ECM) instruments et al. Here, an angular log-periodic meander-line TWT is presented in this article. The angular log-periodic meander-line slow wave structure (SWS) is supported by two diamond rods. The dispersion and the impedance characteristics are analyzed in detail. In order to reduce the reflection loss, a gradual ridged waveguide is connecting the input–output standard rectangular waveguide to the meander-line SWS. The particle in cell (PIC) simulations show that the output power of the TWT can reach 55 W at 34 GHz with the operation voltage of 1800 V and the beam current of 0.2 A. The SWS is manufactured by a laser machine with Molybdenum sheet. The assembled TWT is tested and the results show that the ${S}_{{11}}$ is less than −10 dB at 30–39 GHz. The ${S}_{{21}}$ mismatch between the simulated and the measurement is discussed at the end. [ABSTRACT FROM AUTHOR]

A novel sine groove waveguide slow wave structure (SGW-SWS), originated from the sine waveguide (SW), is proposed for a wideband terahertz (THz) traveling wave tube (TWT). SGW-SWS not only has high interaction impedance in a relatively wide frequency band, but also has a wide beam tunnel. In addition, it can be fabricated using the Nano-Computer Numerical Control (CNC) milling techniques. The high-frequency simulation results show that, under the same dispersion, the passband of SGW-SWS is 23 GHz wider than that of SW-SWS, and the average interaction impedance of SGW-SWS is higher than that of SW-SWS in the whole passband. And the transverse dimension of beam tunnel is independent of the dispersion characteristics of SGW-SWS, so the beam current can be further increased by enlarging the size of beam tunnel. Moreover, the particle-in-cell (PIC) simulation results reveal that the saturated power and electronic efficiency of SGW-TWT in the frequency range of 201–260 GHz are more than 84.9 W and 2.72%, respectively, when the operating voltage is 20.8 kV and the beam current is 150 mA. [ABSTRACT FROM AUTHOR]

In this article, a novel dielectric-supported staggered dual-meander-line (DS-SDML) planar slow-wave structure (SWS) is proposed for a traveling wave tube (TWT) working at ${E}$ -band. The proposed staggered arrangement of meander-lines (MLs) leads to a stronger beam–wave interaction and achieves higher output power as compared to the symmetric arrangement. The input–output couplers have been designed by using staggered stepped double ridge waveguide, to connect the standard ${E}$ -band rectangular waveguide and the DS-SDML SWS. An attenuator and pitch tapering have been applied to the proposed SWS to suppress the unwanted frequencies and to improve the output power. Particle-in-cell (PIC) simulation results show that for an 11.8-kV, 200-mA sheet-beam, the output power can reach 283 W at 75 GHz, with a maximum gain and electronic efficiency of 34.5 dB and 11.9%, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a high-power Ka-band traveling-wave tube (TWT) driven by a sheet electron beam is proposed and demonstrated by means of the simulation and experimental methods. The single grating rectangular waveguide with large width-to-height ratio is used as the slow-wave structure (SWS). An $E$ -plane bend energy coupler is put forward to feed this wide SWS. An irregular transition structure between the input waveguide and the SWS is suggested and designed, which is beneficial to suppress the self-excited oscillation. For a practical electron beam (20 mm $\times \,\, 1$ mm, 150.1 kV, 850 A, and 20-ns), the output power of this single rectangular grating sheet beam TWT is larger than 750 kW from 34.5 to 35.4 GHz. The maximum power is 1.21 MW at 35 GHz, corresponding to a gain of 20.4 dB. [ABSTRACT FROM PUBLISHER]

The sheet beam vacuum electron device is an attractive choice for generating high-power high-frequency microwave radiation. A millimeter-wave sheet beam backward wave oscillator (BWO) is presented in this paper. The rectangular waveguide grating structure is used as its slow wave structure. The BWO is driven by a sheet beam with a cross-sectional area of 30 mm \times 1 mm which is generated by a thin cathode. For a beam voltage of 167 kV and a beam current of 1.4 kA, the output power is 40 MW at 36.6 GHz. The beam–wave interaction efficiency is about 17%, which is higher than that of conventional hollow beam BWO. It is clear from the results presented in this paper that the sheet beam device is promising for producing high-efficiency high-power millimeter-wave radiation. [ABSTRACT FROM AUTHOR]