Search

The reliability of low-voltage inverter-fed motors is highly dependent on the inception of partial discharges. The effect of impulsive waveform parameters must be investigated to predict the repetitive partial discharge inception voltage (RPDIV) and define test procedures that can indicate properly the behavior in service of the insulation system. This paper focuses on the RPDIV of magnet wires using twisted pairs subjected to repetitive unipolar impulsive voltage waveforms. The effects of supply frequency (5 to 200 kHz) at pressure levels that are typical for aircraft (20 to 100 kPa) is examined. Results show that RPDIV steadily decreases with frequency up to 100 kHz where it reaches a plateau. This behavior is explained as an effect of the oscillations that inevitably exist in the applied voltage waveform. Therefore, a conservative estimate of the RPDIV could be achieved by raising the supply frequency well above the operation frequency. In the experiments, the RPDIV is decreasing linearly with pressure. If this behavior could be confirmed for other insulation systems, the design of systems working at pressures typical of aircraft would result relatively easy. [ABSTRACT FROM AUTHOR]

Dealing with electrical rotating machines fed by voltage converters, understanding the effect of impulsive voltage parameters on partial discharge features is of great importance to select appropriate impulsive voltage to perform partial discharge inception voltage measurements. Similarly, the dependence of insulation endurance on voltage parameters might help to develop qualification tests providing more accurate evaluation of insulation performance. The effect of voltage duty cycle on partial discharge characteristics and endurance of inverter-fed motor insulation were investigated through a large number of tests performed on single-contact crossed enameled wires under bipolar repetitive impulse wave voltages. The partial discharge pattern, magnitude, repetition rate show that short impulsive voltage duration (i.e. small duty cycles), can induce asymmetric PD patterns and reduce the probability of PD inception at the falling flanks of impulsive voltages. Moreover, the endurance tests indicate that the duty cycle of the repetitive square wave voltage can affect the insulation endurance significantly. Repetitive square wave voltages with small duty cycles tend to overestimate endurance. Accordingly, when performing partial discharge inception voltage and endurance tests on insulation of inverter-fed motors, the influence of duty cycle should be carefully considered. [ABSTRACT FROM AUTHOR]

To ensure insulation system reliability of rotating machines driven by power electronics, accelerated tests under repetitive impulsive voltages should be performed on turn-to-turn insulation according to the standards provided by the International Electrotechnical Commission. The parameters of repetitive impulsive voltage can significantly influence insulation lifetime, and thus, voltage parameters should be carefully controlled during the accelerated tests. To increase endurance test efficiency when testing many insulation specimens in parallel, the rise time of impulsive voltage should be controlled at certain constant values after the breakdown of one or more specimens to obtain objective endurance test results. This study provides a description of a novel square wave voltage generator used for the insulation evaluation of rotating machines driven by power electronics. A single-channel generator with variable rise times used for one specimen and a multi-channel generator with a constant rise time used to test five specimens in parallel are presented based on a push-pull solid-state switch. In the multi-channel generator, the RC parameter of the high-voltage circuit can be adjusted automatically by resorting to controlling units and a circuit structure after the breakdown of one or more samples when performing endurance tests on parallel specimens to keep the rise time of impulsive voltage at constant values. The multi-channel generator can significantly increase the endurance evaluation efficiency of the insulation systems of rotating machines fed by power electronics. [ABSTRACT FROM AUTHOR]

This paper reviews results of partial discharge measurements and accelerated life tests performed on models of random and form wound insulation systems subjected to impulse voltage waveforms. The goal is to highlight how the features of the supply voltage affect the partial discharge activity and how this, eventually, reflects on the endurance of the insulation system. The most salient results are that, for both types of insulation systems, short rise times trigger PD of large magnitude, which are able to erode the insulation system faster than the partial discharges incepted using waveforms with longer rise times. In particular, failure times estimated by tests under sinusoidal voltages can be overly optimistic in assessing the long-term behavior of the insulation system subjected to impulse voltage waveforms. Frequency also is very important, as it controls the interplay between physical and chemical degradation rates. As a result, above partial discharge inception voltage the frequency acceleration rule does not hold, and can lead therefore to excessively optimistic results. [ABSTRACT FROM AUTHOR]

High voltage equipment designed for DC applications is stressed differently from ac equipment. Most notably, the load conditions of the equipment play a major role in determining the electric field distribution in insulation under dc, due to the temperature dependence of conductivity. Additionally, polarization and space charge phenomena impose a time dependent behavior on the stress distribution. This has major consequences for the way in which degradation of the insulation under dc stress takes place. The nature of the stresses under dc may lead to accelerated degradation processes which could result in early breakdown of the insulation. This paper provides an overview of the stress conditions specific for dc application and highlights via which routes they may lead to failure. The stress distributions in converter transformers and dc cable systems will serve as typical examples. [ABSTRACT FROM AUTHOR]

This paper focuses on the influence of repetitive square wave voltage rise time on partial discharge pulse characteristics in the ultra-high frequency range. Paerial Discharge (PD) tests on single-point contact crossed pairs were carried out using repetitive square wave voltages with a wide range of rise times, from 200 ns to 400 μs, including also 50 Hz sinusoidal voltage waveforms. Experimental results show that rise time has a significant influence on magnitude and frequency spectrum of PD pulses. Voltages of shorter rise times generate larger PD pulses with a predominance of high frequency components in the energy spectrum. Interpretations are presented for this phenomenon. [ABSTRACT FROM AUTHOR]

Inter-time (i.e., the time that separates a PD event from the next one) distribution analysis has been recently proposed as a tool to infer the presence of trees in solid insulation systems. In this paper, inter-time distribution analysis is improved to infer more accurately trees at an early growth stage. Measurements from both artificial specimens as well as practical objects are presented to support the effectiveness of this tool. Moreover, considerations on inter-time analysis robustness with respect to both noise interference and other partial discharge sources are reported. [ABSTRACT FROM AUTHOR]

An experimental investigation of the behavior of partial discharges occurring in insulation cavities as a function of light irradiation conditions is presented in this paper. Partial discharge inception voltage (PDIV) measurements were performed for different irradiation conditions of the test objects (visible light, of variable intensity, ultra violet (UV) light or absence of irradiation), defect geometry and conductivity of insulating material. It is shown that changes of such factors involve con siderable alteration of partial discharge inception features, in terms of both inception voltage and delay time. Depending on applied field, defect geometry, insulating material characteristics and irradiation condition, in fact, partial discharge inception voltage may be influenced prevailingly by background radiation, as generally stated in literature, or by field-assisted electron detrapping from material. cavity interface. [ABSTRACT FROM AUTHOR]

In the framework of developing defect-based life models, in which breakdown is explicitly associated with partial discharge (PD)-induced damage growth from a defect, ageing tests and PD measurements were carried out in the laboratory on polyethylene (PE) layered specimens containing artificial cavities. PD activity was monitored continuously during aging. A quasi-deterministic series of stages can be observed in the behavior of the main PD parameters (i.e. discharge repetition rate and amplitude). The evolution of the parameters reflects the physicalchemical changes taking place at the dielectric/cavity interface during the aging process. PD activity shows similar time behavior under constant cavity gas volume and constant cavity gas pressure conditions, suggesting that the variation of PD parameters may not be attributed to the variation of the gas pressure. It is speculated that the change of PD activity is related to the composition of the cavity gas, as well as to the properties of dielectric/cavity interface. [ABSTRACT FROM AUTHOR]