Search

In this paper, the PD properties of an ester oil/PB and a mineral oil/PB system undergoing a moisture transient are investigated using a needle-plane electrode under natural cooling. The temperature, moisture concentration and water activity of the oil are continuously monitored. Moreover, an improved moisture diffusion model is developed by using COMSOL Multiphysics to verify the experimental results. The measurement results show that there is a sharp reduction of partial discharge inception voltage (PDIV) or a sudden increase of PD intensity in the process of natural cooling for both ester oil and mineral oil system. However, the PDs extinguish gradually after the occurrence of the minimum of PDIV. For the cooling mode selected in this study, the minimum of PDIV for the ester oil system appears in the third hour after cooling begins, while it is about in the second hour for the mineral oil system. In addition, the simulation results are consistent with the experimental data. [ABSTRACT FROM AUTHOR]

Partial discharge inception voltage measurements under repetitive impulsive voltages play an essential role in evaluating the reliability of inverter-fed low voltage rotating machines. Using impulsive voltages, partial discharge (PD) signals and the disturbance induced by power electronics switches have often similar energy distribution in the frequency domain. Thus, PD test technologies used with sinusoidal voltages are no longer effective. Under repetitive impulsive voltages, ultra-high frequency detection is recommended to couple high-frequency spectral components from the PD and remove the low-frequency disturbance coming from power electronics. However, to obtain high signal to noise (S/N) ratio, the parameters of the antenna used for PD detection should be designed considering the PD and the disturbance energy distributions in the frequency domain. In this paper, we discuss the design and show the properties of an antenna with Archimedes plane spiral structure intended for PD detection under repetitive impulse voltages. The simulation shows that the antenna has low voltage standing wave ratio (<2) and improved directivity in the frequency range from 0.5 to 2 GHz. Moreover, PD tests performed using repetitive square waves with different rise times demonstrate that the designed antenna can receive PD signals efficiently with high S/N. [ABSTRACT FROM AUTHOR]

The reliability of low-voltage inverter-fed motors is highly dependent on the inception of partial discharges. The effect of impulsive waveform parameters must be investigated to predict the repetitive partial discharge inception voltage (RPDIV) and define test procedures that can indicate properly the behavior in service of the insulation system. This paper focuses on the RPDIV of magnet wires using twisted pairs subjected to repetitive unipolar impulsive voltage waveforms. The effects of supply frequency (5 to 200 kHz) at pressure levels that are typical for aircraft (20 to 100 kPa) is examined. Results show that RPDIV steadily decreases with frequency up to 100 kHz where it reaches a plateau. This behavior is explained as an effect of the oscillations that inevitably exist in the applied voltage waveform. Therefore, a conservative estimate of the RPDIV could be achieved by raising the supply frequency well above the operation frequency. In the experiments, the RPDIV is decreasing linearly with pressure. If this behavior could be confirmed for other insulation systems, the design of systems working at pressures typical of aircraft would result relatively easy. [ABSTRACT FROM AUTHOR]

This work assesses the initial and crucial part of electrical treeing degradation, the inception stage, focusing on its dependence on applied voltage waveform and frequency. Tests have been performed on needle-plane configuration samples in solids and gels. A physical model has been formulated through an adaptation of an established theory for solids in which electrical tree inception is related to damage-producing injection currents. The voltage rise time appeared to be the most important parameter influencing the tree inception in the gel, while in the solid material the frequency is more relevant. The analysis leads to the conclusion that tree inception in gels is due to a single high-energy event, in contrast to what is commonly known for solids where damage accumulation takes place. A tree inception model is proposed for the gel, in which initiation is driven by a pressure wave generated by the electric field and the space charge injected into the sample. The model fits the experimental data and may be used to predict the tree initiation for different waveforms and voltage values. [ABSTRACT FROM AUTHOR]

Dealing with electrical rotating machines fed by voltage converters, understanding the effect of impulsive voltage parameters on partial discharge features is of great importance to select appropriate impulsive voltage to perform partial discharge inception voltage measurements. Similarly, the dependence of insulation endurance on voltage parameters might help to develop qualification tests providing more accurate evaluation of insulation performance. The effect of voltage duty cycle on partial discharge characteristics and endurance of inverter-fed motor insulation were investigated through a large number of tests performed on single-contact crossed enameled wires under bipolar repetitive impulse wave voltages. The partial discharge pattern, magnitude, repetition rate show that short impulsive voltage duration (i.e. small duty cycles), can induce asymmetric PD patterns and reduce the probability of PD inception at the falling flanks of impulsive voltages. Moreover, the endurance tests indicate that the duty cycle of the repetitive square wave voltage can affect the insulation endurance significantly. Repetitive square wave voltages with small duty cycles tend to overestimate endurance. Accordingly, when performing partial discharge inception voltage and endurance tests on insulation of inverter-fed motors, the influence of duty cycle should be carefully considered. [ABSTRACT FROM AUTHOR]

To ensure insulation system reliability of rotating machines driven by power electronics, accelerated tests under repetitive impulsive voltages should be performed on turn-to-turn insulation according to the standards provided by the International Electrotechnical Commission. The parameters of repetitive impulsive voltage can significantly influence insulation lifetime, and thus, voltage parameters should be carefully controlled during the accelerated tests. To increase endurance test efficiency when testing many insulation specimens in parallel, the rise time of impulsive voltage should be controlled at certain constant values after the breakdown of one or more specimens to obtain objective endurance test results. This study provides a description of a novel square wave voltage generator used for the insulation evaluation of rotating machines driven by power electronics. A single-channel generator with variable rise times used for one specimen and a multi-channel generator with a constant rise time used to test five specimens in parallel are presented based on a push-pull solid-state switch. In the multi-channel generator, the RC parameter of the high-voltage circuit can be adjusted automatically by resorting to controlling units and a circuit structure after the breakdown of one or more samples when performing endurance tests on parallel specimens to keep the rise time of impulsive voltage at constant values. The multi-channel generator can significantly increase the endurance evaluation efficiency of the insulation systems of rotating machines fed by power electronics. [ABSTRACT FROM AUTHOR]

The purpose of this paper is to understand the pros and cons of aluminum conductors insulated with anodized aluminum for rotating machines used in aircraft. The investigation is focused on the breakdown voltage and partial discharge inception voltage of simple systems (crossed pairs, simplified coils). The results show that both breakdown voltage and partial discharge inception voltage are very sensitive to curvature radius and lower than those achieved using conventional copper conductors insulated with polymeric enamels. However, the operating temperature of the insulation (600 ?C) is extremely appealing. Therefore, it could be interesting to devise high temperature fillers and suitable manufacturing procedures to exploit this insulation system in specific applications, where the weight of the machine is the key factor for material selection. [ABSTRACT FROM AUTHOR]

This paper reviews results of partial discharge measurements and accelerated life tests performed on models of random and form wound insulation systems subjected to impulse voltage waveforms. The goal is to highlight how the features of the supply voltage affect the partial discharge activity and how this, eventually, reflects on the endurance of the insulation system. The most salient results are that, for both types of insulation systems, short rise times trigger PD of large magnitude, which are able to erode the insulation system faster than the partial discharges incepted using waveforms with longer rise times. In particular, failure times estimated by tests under sinusoidal voltages can be overly optimistic in assessing the long-term behavior of the insulation system subjected to impulse voltage waveforms. Frequency also is very important, as it controls the interplay between physical and chemical degradation rates. As a result, above partial discharge inception voltage the frequency acceleration rule does not hold, and can lead therefore to excessively optimistic results. [ABSTRACT FROM AUTHOR]

In this work, we compare the dielectric withstand performance of nanofluids prepared using Shell Diala D as a base fluid, and magnetite, graphene oxide and silicone dioxide as nanoadditives. The ac withstand capability of the nanofluids was investigated as well as partial discharge inception voltage, partial discharge and repetition rate under ac, dc positive and dc negative voltages. The results indicate that, for all nanofluids, nanoparticle concentrations around 0.2 g/l enhance dielectric withstand properties under quasi uniform fields. Under divergent fields, partial discharge characteristics are improved under ac conditions. Under dc conditions silica nanofluid performs better than mineral oil, but the other two nanofluids do not perform well. [ABSTRACT FROM AUTHOR]

High voltage equipment designed for DC applications is stressed differently from ac equipment. Most notably, the load conditions of the equipment play a major role in determining the electric field distribution in insulation under dc, due to the temperature dependence of conductivity. Additionally, polarization and space charge phenomena impose a time dependent behavior on the stress distribution. This has major consequences for the way in which degradation of the insulation under dc stress takes place. The nature of the stresses under dc may lead to accelerated degradation processes which could result in early breakdown of the insulation. This paper provides an overview of the stress conditions specific for dc application and highlights via which routes they may lead to failure. The stress distributions in converter transformers and dc cable systems will serve as typical examples. [ABSTRACT FROM AUTHOR]