Search

The radiowave propagation through hollow clay brick walls, which are common in southern European construction, is analyzed. The brick walls have thicknesses of 11, 15, and 20 cm, common in both interior and exterior walls, and are bound with a portland cement, water, and sand mixture. For each brick dimension, three prototypes were assembled, varying in the type of wall finish, i.e., exposed brick, smooth painted plaster, and rough painted plaster. A 10 cm concrete wall was also included for comparison purposes. Penetration loss metrics were evaluated in an anechoic chamber at frequencies ranging from 680 MHz to 10 GHz. Results demonstrate that the brick wall internal heterogeneity, as well as the type of finish, significantly influences the propagation phenomena and thus the frequency response of the walls, with relatively high penetration losses observed at some relevant commercial frequency bands. Finally, an alternative brick design, with reduced penetration losses, is also proposed and evaluated under simulation environment only. [ABSTRACT FROM AUTHOR]

This paper describes an extensive propagation channel measurement campaign in a warehouse environment for line-of-sight (LOS) and nonline-of-sight (NLOS) scenarios. The measurement setup employs a vector network analyzer operating in the 2–8-GHz frequency band combined with an $8 \times 8$ virtual multiple-input multiple-output (MIMO) antenna array. We develop a comprehensive statistical propagation channel model based on high-resolution extraction of multipath components and subsequent spatiotemporal clustering analysis. The intracluster direction of departure (DoD), direction of arrival (DoA), and the time of arrival (ToA) are independent, both for the LOS and NLOS scenarios. The intracluster DoD and DoA can be approximated by the Laplace distribution, and the intracluster ToA can be approximated by an exponential mixture distribution. The intercluster analysis, however, shows a dependency between the cluster DoD, DoA, and ToA. To capture this dependency, we separately model the clusters caused by single and multiple bounce scattering along the aisles in the warehouse. The intercluster DoD distribution follows a Laplace distribution, while the cluster DoA conditioned on the DoD is approximated by a Gaussian mixture distribution. The model was validated using the capacity and delay-spread values. [ABSTRACT FROM AUTHOR]

In ultra-wideband (UWB) wireless propagation channels, each multipath component (MPC) can exhibit delay dispersion or, equivalently, frequency dependence; even more, this dispersion can be different for different MPCs. While this effect is understood to have important implications for UWB system design, extraction of the frequency-dependence parameters from measurements has been lacking. This paper will provide both the theoretical tools for the parameter extraction, and provide experimental results of such parameters in UWB indoor channels. We first develop a method that extracts a single MPC. Based on the image principle, the method identifies locations and intensity of radio sources including both original and image sources (corresponding to MPCs) by a distributed antenna array. We show that the method provides spatial resolution better than 0.5 m and is robust against possible measurement errors. Having applied the method to the measured channels in indoor line-of-sight scenarios, we track the detected image sources over (partially overlapping) frequency subbands to obtain frequency dependent properties of their intensity and location. The variation of the source intensity over the frequency was found to be significant. Furthermore, the locations of the image sources can vary as the frequency changes. Comparison of the results with models that do not describe varying per-path frequency dependence revealed noticeable difference in the shape of the CIRs, and as a result, in the delay spread and the number of significant delay bins for Rake reception. [ABSTRACT FROM PUBLISHER]

The wireless harness is a new emerging short-range communication to replace wire harness implemented in devices with wireless communications between internal components. In such an in-device wireless harness, the communication distance is up to a couple of meters at most. Through the challenge to apply this wireless communication technology to information and communication technology (ICT) equipment, we found that the radio channel inside the ICT equipment deeply depends on its internal structure more than we expected. In order to understand the radio propagation characteristics inside such equipment, we propose a new modeling technique with using a frequency- dependent path loss exponent expressing the near- and far-field propagation, which enables us to successfully extract attenuation factors for the frequency and the propagation distance from the measured data. The results shows the path loss characteristics can be divided into three regions; line-of-sight (LOS), non-line-of-sight (NLOS), and a transition range. The transition range, which appears between the LOS and the NLOS, is caused by a blocking due to the densely-packaged internal components. These findings and equations can be criteria to design a wireless harness communication link. [ABSTRACT FROM AUTHOR]