Search

This article presents a novel triband dual-polarized shared-aperture antenna with frequency-selective function for sub-6 GHz base station applications. The proposed antenna is composed of a dual-polarized square loop antenna with two parasitic loops for 2G/3G/4G (1710–2690 MHz) and a differentially fed dual-polarized planar antenna for 5G (3300–3600 and 4800–5000 MHz) base station applications. These two antennas are placed coaxially but different altitudes for saving the installation space. In order to achieve good individual performance for these two antennas in the same aperture without interference or blocking, the lower band (LB) antenna is designed as a frequency-selective surface (FSS) for the nether mid/upper bands (M/UBs) antenna. The measured results show that the proposed antenna achieves a high port isolation (>20 dB) between LB and M/UBs and a −10-dB impedance bandwidth of 50.4% (1.60–2.70 GHz), 14.9% (3.28–3.80 GHz), and 8.6% (4.75–5.18 GHz). To further validate the design concept, an antenna array composed of four LB elements and eight M/UBs elements with the corresponding spacing is fabricated and measured, which demonstrates the application of the triband shared-aperture antenna in array form. [ABSTRACT FROM AUTHOR]

A wideband traveling-wave circularly polarized (CP) antenna printed on a single-layer PCB for millimeter-wave (MM-Wave) applications is presented in this communication. The proposed antenna radiates the CP wave on the basis of the principle similar to the classical endfire-mode helical antenna. The proposed antenna is terminated with an absorber to realize traveling-wave radiation. The traveling-wave working mechanism causes the proposed antenna to have a frequency scanning function and higher stability compared with resonant antennas. Curved microstrip transmission lines are adopted as the CP radiation elements; the whole array antenna is etched on a single-layer substrate. A prototype operating at 30 GHz is fabricated and measured. The radiation beam of the proposed antenna scans from − 14.5° (28 GHz) to +22.5° (34 GHz), the axial ratios are lower than 3 dB, and the measured gains show a maximum value of 21.9 dBi at 33 GHz and a minimum value of 20.3 dBi at 28 GHz. The measured $| \text {S}_{11} |$ and $| \text {S}_{21} |$ are lower than −10 and −16 dB, respectively, in the frequencies mentioned above. [ABSTRACT FROM AUTHOR]

This communication presents a beam-deflection short backfire antenna (BD-SBA). The proposed BD-SBA differs from the conventional SBA in that the main reflector of the BD-SBA is a phase-modulated metasurface instead of a perfect electric conductor (PEC). The phase-modulated metasurface consists of 15 columns of unit cells which are designed to change the phase of the reflected waves. Therefore, the beam of the BD-SBA can be deflected to a certain angle. First, several BD-SBAs with linear phase-modulated metasurfaces are studied, which indicates that the beam of antennas point at different directions. Second, the BD-SBAs with nonlinear phase-modulated metasurfaces are studied to compare the difference between metasurfaces with linear and nonlinear width variation of patch. The simulated results show that the metasurface with nonlinear variation can obtain better performance than the former. To verify this design method, the BD-SBA with $\Delta \theta = 10^{\circ }$ was fabricated and measured at ${X}$ -band. The overall height of the proposed antenna is 0.35 wavelength at 10 GHz. The measured and simulated results are in good agreement; the measured beam-deflection angle, realized gain, and aperture efficiency are 10°, 14.8 dBi, and 68.3% at the center frequency, respectively. Due to the beam-deflection function, medium-to-high gain characteristics, and low profile, the proposed BD-SBA can be expected to find potential applications in wireless backhauling. [ABSTRACT FROM AUTHOR]

This communication presents a dual-polarized series-fed array antenna with 30° beam-pointing for millimeter-wave (MM-Wave) applications. The 45° and −45° polarized subarrays share the aperture in an interdigital shape. The spacing between subarrays with the same polarization orientation is set to $0.56\lambda _{0}$ through the use of narrower T-type folded substrate integrated waveguide (TFSIW) instead of substrate integrated waveguide (SIW). The substrate integrated coaxial line (SICL) is adopted to design the array feeding network. To validate the proposed design, a $4 \times 6$ (single polarization) dual-polarized array antenna operating at 28 GHz with 30° beam-pointing is fabricated. Based on the measurement, the return losses are lower than −10 dB from 27.5 to 28.5 GHz, the isolations between the two polarization ports are higher than 30.0 dB in the frequencies mentioned above, the maximum gain at the center frequency is 15.7 dBi, and the cross-polarization levels are lower than −18.5 dB. The proposed antenna only needs one-step processing with the standard PCB technology without additional stitching assembly. Simulated and measured results of the proposed antennas were compared. [ABSTRACT FROM AUTHOR]

Single fed low profile cavity backed crossed slot antennas for dual frequency dual linear polarization and circular polarization applications are first presented in this paper. By employing the substrate integrated waveguide (SIW) technique in the antenna designs, the low profile backed cavity structure can be realized by using only a single layer of low cost printed circuit board (PCB) substrate. A single grounded coplanar waveguide (GCPW) is employed as the feeding element to excite the TE120 and TE210 modes in the SIW cavity. A crossed slot structure is used as the radiating element in order to radiate the desired dual linearly or circularly polarized wave. From the measurement results, it is seen that these novel antennas retain the advantages of conventional metallic cavity backed antennas, including high gain, high front-toback ratio (FTBR), and low cross polarization level (CPL). Furthermore, the proposed antennas also possess the advantages of low profile, light weight, low fabrication cost, and easy integration with planar circuits. [ABSTRACT FROM AUTHOR]