Search

There is a relative lack of research on the development of creepage discharge in aged oil-paper insulation subjected to AC-DC combined voltage in converter transformers. In this study, based on the physical and chemical properties of oil-paper, we propose a sphere-plate electrode model to study the creepage discharge parameters and characteristic spectra of aged oil-paper subjected to AC-DC combined voltage. The results show that the creepage discharge inception voltage of aged oil-paper is related to the AC voltage component of the AC-DC combined voltage. However, when the DC voltage component is 60 kV, the flashover phenomenon was found to occur in one of the severely aged samples before the AC voltage was applied. Despite being subjected to the same DC voltage, the flashover phenomenon did not occur in three other samples aged to different degrees. Large-amplitude discharges were found to appear earlier in the severely aged samples. At the same creepage discharge stage, as the aging time of the oil-paper increased, the number of large-amplitude discharges was found to rapidly increase, and the time interval between adjacent discharges was found to gradually decrease. At each stage of the creepage discharge, the small-amplitude discharge has a “hump” shaped distribution. The larger the DC voltage component, the shorter the endurance time of aged oil-paper, and the more severe the damage to the oil-paper. The DC voltage component was found to have an accelerating effect on the development of creepage discharge in aged oil-paper insulation.

This paper presents a broadband, simple, re-useable and low-cost approach for noninvasive sweat monitoring using a passive microwave circuit and a cellulose filter paper as a superstrate. The proposed sensor is composed of filter paper with the ability to absorb the sample liquid under test (LUT) placed on top of a coplanar waveguide (CPW) transmission line. Various samples of sodium chloride (NaCl) solutions with concentrations in the range of 0.01-2 mol/L and models of artificial sweat are used to test the proposed sensor. The difference in transmission coefficient (S21) between dry and wet states is used to determine the concentrations of tested solutions in the band of 1-6 GHz. The sensor detects concentrations as low as 0.01 mol/L (0.58 g/L) and quantities as low as 137 μL with a maximum sensitivity of 46.7 dB/g/L. The proposed sensor presents a simple approach to sample and characterize liquids with enhanced sensitivity and consistent performance using microwave signals.

The oil-paper insulation in power transformer is under a complicated environment, and there is little research on the combined effects of winding vibration-generated mechanical stress and thermal stress on the aging of insulating paper. To investigate the effects of combined mechanical-thermal stress on the aging properties of insulating paper, this paper carried out accelerated aging test using the as-designed mechanical-thermal stress combined aging oven in the aging environment at the temperature of 130 °C, and the mechanical stress intensities of 1 MPa, 1.5 MPa and 2 MPa. Besides, the degree of polymerization (DP), tensile strength, infrared spectroscopy, and scanning electron microscope (SEM) tests were performed on the aging paper samples. The test results suggested that, the combined mechanical-thermal aging might be regarded as thermal aging with lower degradation activation energy; the DP and tensile strength of insulating paper markedly declined during the mechanical-thermal aging process. At the same time, mechanical stress promoted the destruction of glycosidic bond, intramolecular and intermolecular hydrogen bonds, and increased the insulating paper cracks and holes. Typically, the above factors accelerated the aging of insulating paper. Finally, an improved degradation rate equation for insulating paper with consideration of mechanical stress was put forward.

Insulated tubular busbar is a new type of current-carrying equipment with excellent performance. However, the research on this equipment is insufficient because of the short application and the lack of technical digestion, which has resulted in many accidents. In this paper, the full-scale model of epoxy-impregnated-paper insulated tubular busbar with bubble defects was designed and produced, its electrical breakdown process was investigated by withstand voltage test. In the experiment, the failure mode of breakdown caused by gas expansion was found for the first time. The research showed that the electrical-mechanical breakdown process could be divided into two stages: gas increase stage and breakdown threshold stage. The research also obtained the characteristics and the change criterions of the two stages. The gas in the bubble defects generated from epoxy decomposition which caused by partial discharge. When the gas pressure exceeds the critical fracture toughness of the bubble defects wall, the unstable crack extension occurs, therefore, improving the ability about resistance to partial discharge of epoxy resin or improving the fracture toughness of epoxy resin by modifying would enhance the breakdown performance of insulated tubular busbar. The result also has reference significance for other epoxy-impregnated-paper insulated electrical equipment.

This paper presents the design and analysis of a paper-based chipless RFID sensor for wetness content measurement in plant leaves. The sensor is designed using a passive microwave resonator to measure the ambient physical parameter. The resonator is designed with a rectangular loop inductively coupled with an interdigital capacitor. The experimental analysis of the designed sensor is illustrated here to prove its efficacy. The resonator provides adequate backscattered signal for wireless measurement in the microwave frequency band. When interrogated with a couple of UWB antennas and a VNA, it yields accurate leaf wetness response of the plant. The commercial competence of this sensing device is validated through its experimental analysis on three different types of leaf samples. This sensor is suitable for plant health monitoring in any small-scale gardening applications such as nurseries and greenhouses.

This paper investigates the impact of institutes and papers over time based on the heterogeneous institution-citation network. A new model, IPRank, is introduced to measure the impact of institution and paper simultaneously. This model utilises the heterogeneous structural measure method to unveil the impact of institution and paper, reflecting the effects of citation, institution, and structural measure. To evaluate the performance, the model first constructs a heterogeneous institution-citation network based on the American Physical Society (APS) dataset. Subsequently, PageRank is used to quantify the impact of institution and paper. Finally, impacts of same institution are merged, and the ranking of institutions and papers is calculated. Experimental results show that the IPRank model better identifies universities that host Nobel Prize laureates, demonstrating that the proposed technique well reflects impactful research. Refereed/Peer-reviewed

Moisture content and aging of oil-paper insulation are two important factors that cause deterioration of the insulation performance of power transformers. The water molecules and aging products are polar, which affects the dielectric response characteristics of the insulation system. Currently, the dielectric response testing technology has realized non-destructive evaluation of the moisture content of transformer insulation. However, the changes in the dielectric response caused by aging products are easily concealed by the influence of moisture, which makes the diagnostic technology ineffective for use in the evaluation of the aging of the oil-paper system. In order to avoid drawback, a new method utilizing frequency domain dielectric spectroscopy (FDS) and the water balance characteristics of the oil-paper insulation is proposed in this paper to evaluate the aging state of oil-paper insulation. The aging of oil-paper insulation will affect the water balance between oil and paper. In this paper, the experimental studies have shown that the water distribution coefficient between oil and paper and the degree of polymerization (DP) of the insulating paper shows a significant linear relationship. Accordingly, in this paper, FDS curves were used to evaluate the moisture content in the insulating paper, oil samples were taken to measure the moisture content in oil, and then the ratio of moisture content in oil and paper were calculated as the aging characteristic parameter. The linear relationship between the characteristic parameter and DP was used to evaluate the aging state of oil-paper insulation. The feasibility of the proposed method is preliminarily verified using oil-paper insulation samples at different aging states and with different moisture levels in the laboratory.

Studying the moisture diffusion in non-oil-immersed insulation paper is helpful to optimize the drying process and improve the drying efficiency of oil-immersed equipment. Moisture diffusion factor (MDF) is the key parameter to describe the moisture diffusion in non-oil-immersed insulation paper. Thermal aging affects the moisture absorption capacity of insulation paper obviously, thus, this paper intends to modify the empirical expression of MDF by considering the effects of thermal aging. The transient moisture contents of non-oil-immersed insulation paper with different thicknesses were measured at 40 °C and 60 °C, respectively. Then, the experimental values of MDF were extracted, and the empirical expression of MDF was modified by considering the effects of thermal aging. Finally, the modified expression of MDF was verified. The following conclusion can be obtained: 1) the equilibrium time constant of non-oil-immersed insulation paper increases with thermal aging; 2) the moisture absorption rate of non-oil-immersed insulation paper decreases with thermal aging, and; 3) the modified expression of MDF is reasonable and effective.

Oil-immersed insulation paper (OIP) bushing is one of the most important equipment in power transmission and distribution systems. Moisture is one of the most serious factors that affect the insulation status of OIP bushing. In this paper, the OIP bushing was assumed to be in a stable and simplicity condition, and then the transient moisture distribution of capacitor core and its effects on the electric field were studied. First, by dissecting a 110 kV OIP bushing, the specific sizes for modelling were obtained. Afterwards, a moisture diffusion model for OIP bushing was established based on COMSOL Multiphysics software, and it was also verified by moisture diffusion experiment. Then, the moisture distribution for different conditions were obtained and analyzed. Finally, a model for the electric field of OIP bushing was established, and then the effects of moisture on the electric field were studied.

The volume of research articles in digital repositories is increasing. This spectacular growth of repositories makes it rather difficult for researchers to obtain related research papers in response to their queries. The problem becomes worse when a researcher with insufficient knowledge of searching research articles uses these repositories. In the traditional recommendation approaches, the results of the query miss many high-quality papers, in the related work section, which are either published recently or have low citation count. To overcome this problem, there needs to be a solution which considers not only structural relationships between the papers but also inspects the quality of authors publishing those articles. Many research paper recommendation approaches have been implemented which includes collaborative filtering-based, content-based, and citation analysis-based techniques. The collaborative filtering-based approaches primarily use paper-citation matrix for recommendations, whereas the content-based approaches only consider the content of the paper. The citation analysis considers the structure of the network and focuses on papers citing or cited by the paper of interest. It is therefore very difficult for a recommender system to recommend high-quality papers without a hybrid approach that incorporates multiple features, such as citation information and author information. The proposed method creates a multilevel citation and relationship network of authors in which the citation network uses the structural relationship between the papers to extract significant papers, and authors' collaboration network finds key authors from those papers. The papers selected by this hybrid approach are then recommended to the user. The results have shown that our proposed method performs exceedingly well as compared with the state-of-the-art existing systems, such as Google scholar and multilevel simultaneous citation network.

Transformer insulation paper is a key indicator for transformer remaining operational life. Paper decomposition is evaluated using the degree of polymerization (DP) which calls for samples of insulation paper from operating transformers. Since collecting such paper samples is extremely difficult, other indicators have been used to indirectly reveal the DP value of insulation paper. This includes dissolved gases in transformer oil such as carbon oxides and hydrocarbon gases, furan compounds, methanol, ethanol, and moisture along with some oil characteristics such as interfacial tension. However, for the same oil sample, these individual parameters lead to different DP values. This is attributed to the lack of accuracy of the established mathematical and artificial intelligence models correlating DP with each of the above mentioned individual parameters. This paper presents a self-learning method to estimate the DP value of transformer insulation paper based on multiple transformer oil aging parameters. The proposed method comprises data processing, fuzzy c-means and linear regression. Results reveal that estimating the DP value based on multiple aging parameters is more accurate than estimating it using one single parameter as per the current practice. The proposed method not only helps to understand the correlation between multiple oil aging parameters and the DP value of paper insulation, but also promotes the establishment of more accurate life assessment models for power transformers based on these oil aging parameters.

Evolutionary game dynamics is a combination of game theory and dynamical systems. Using dynamical theory, we investigate chaotic behavior in asymmetric Rock-Paper-Scissors games under imitative dynamics with two different populations. Our theoretical analysis and numerical simulations demonstrate that the dynamical system can give rise to chaotic behavior in zero-sum and positive-sum asymmetric games. However, chaos cannot occur in a negative-sum asymmetric game. In particular, the numerical simulations show that there is a limit cycle in a negative-sum asymmetric game.

Methanol is regarded as an available indicator to analyze the aging condition of cellulose insulation. However, the diffusion mechanism of methanol molecules in the paper-oil insulation system is still unclear, since it cannot be explored by using only experiments. Given this issue, the molecular dynamics simulations were performed to investigate the diffusion mechanism of methanol molecules. In the current work, the mean square displacement of methanol during the diffusion process was calculated and analyzed, as well as its trajectory tracking. Then, the research on interaction energies and hydrogen bonds in paper/oil system were conducted. Finally, the effect of temperature on the diffusion of methanol molecules was also studied. Findings revealed that the diffusion of methanol in cellulose insulation is faster than that in insulating oil, besides, the presence of hydrogen bonds affects the diffusion rate of methanol molecules in cellulose insulation and insulating oil. Thus, the present findings could support the investigation of the diffusion mechanisms of methanol molecules, by which the aging condition evaluation of cellulose insulation could be also promoted.

Accurate modeling and simulation of electric field transients in HVDC cables is an important support to optimize insulation system design and to evaluate the influence of voltage transients and steady-state conditions on accelerated ageing mechanisms and insulation reliability. Traditionally, field models considering time-independent permittivity and conductivity are used, but this approach neglects polarization mechanisms and charge trapping-detrapping phenomena. This article includes polarization dynamics in the field model and shows that its impact on transient electric field simulations in HVDC paper-insulated cables can be significant. A method is presented to infer the model parameters from experimental polarization and depolarization current measurements.

Over the decades, the immense growth has been reported in research publications due to continuous developments in science. To date, various approaches have been proposed that find similarity between research papers by applying different similarity measures collectively or individually based on the content of research papers. However, the contemporary schemes are not conceptualized enough to find related research papers in a coherent manner. This paper is aimed at finding related research papers by proposing a comprehensive and conceptualized model via building ontology named COReS: Content-based Ontology for Research Paper Similarity. The ontology is built by finding the explicit relationships (i.e., super-type sub-type, disjointedness, and overlapping) between state-of-the-art similarity techniques. This paper presents the applications of the COReS model in the form of a case study followed by an experiment. The case study uses InText citation-based and vector space-based similarity measures and relationships between these measures as defined in COReS. The experiment focuses on the computation of comprehensive similarity and other content-based similarity measures and rankings of research papers according to these measures. The obtained Spearman correlation coefficient results between ranks of research papers for different similarity measures and user study-based measure, justify the application of COReS for the computation of document similarity. The COReS is in the process of evaluation for ontological errors. In the future, COReS will be enriched to provide more knowledge to improve the process of comprehensive research paper similarity computation.

We present a novel implementation of a Rock-Paper-Scissors (RPS) game interaction with a social robot. The framework is tailored to be computationally lightweight, as well as entertaining and visually appealing through collaboration with designers and animators. The fundamental gesture recognition pipeline employs a Leap motion device and two separate machine learning architectures to evaluate kinematic hand data on-the-fly. The first architecture is used to recognize and segment human motion activity in order to initialize the RPS play, and the second architecture is used to classify hand gestures into rock, paper or scissors. The employed tabletop robot interacts in the RPS play through unique animated gestural movements and vocalizations designed by animators which communicate the robot's choices as well as cognitive reflection on winning, losing and draw states. Performance of both learning architectures is carefully evaluated with respect to accuracy, reliability and run time performance under different feature and classifier types. Moreover, we assess our system during an interactive RPS play between robot and human. Experimental results show that the proposed system is robust to user variations and play style in real environment conditions. As such, it offers a powerful application for the subsequent exploration of social human-machine interaction.

In this paper, we present a new scheme for implementing virtual keyboards, which uses only two to four motion-recognition rings per hand and a two-dimensional keyboard template (e.g., an A4 size paper with printed key positions). It has the benefit of portability, customizability, and low-cost when compared with existing approaches. Essentially, we have shown that wearing two wireless IoT rings on the middle phalanges of two fingers of each hand, users can input the alphabetic characters into a computing device by typing on a flat paper on a desk, and potentially in mid-air. We have demonstrated that two rings are sufficient in capturing the gestures and motions of all fingers in a typing hand for keystrokes recognition. A single wireless IoT ring, which weighs 7.8 grams, consists of a Bluetooth low energy (BLE) unit, a micro inertial measurement unit (mIMU), and a cell battery. The 3-axes attitude angles and the Z-axis acceleration of each ring are adopted as the features for keystroke recognition. The overall keystroke recognition accuracy rate can reach as high as 94.8% when two IoT rings are worn by a user on each hand; this accuracy rate increases to 98.6%, when four rings are worn on each typing hand.

The study is a vital instance to merge the psychology and the computer science disciplines to provide benefits about the developments of the theory of mind (ToM) skills of and interaction with for the students with neurodevelopmental disorders (SWND). In this research, a traditional two-dimensional (2D) method (paper), a 2D display touch screen and the three-dimensional (3D) [augmented reality (AR)] visual displays based on the computer are constructed for the SWND to do the ToM test questions. In this work, The Little Prince story written by Antoine de Saint-Exupéry is adapted to the ToM test questions to measure the SWND's ToM abilities. In this novel approach, three environments: a traditional 2D method (paper), the 2D display touch screen, and the AR visual display environments are experienced by the SWND. The experimental results are compared according to SWND's ToM success ratios, their ToM perspective skills', their satisfaction on these different test environments. This research suggests the novel approach to measure the ToM abilities of the SWND with human-computer interaction aspect. This article displays the positive effects of the 2D display touch screen and the AR usage on the Tom Test for the SWND.

This paper presents a thorough review of transmitarray devices particularly aiming antenna beamsteering, gathering some of the most relevant solutions published by the scientific community in the field. First, the background for realizing 1-D and 2-D antenna beamsteering with a transmitarray is introduced. Subsequently, several examples of unit-cells for transmitarray implementation and complete transmitarray designs presented in the literature are outlined. Each solution is analyzed in detail, identifying the nature of its layout, e.g., based on microstrip patches, frequency selective surfaces (FSS), or metamaterials (MMs), and the method employed to enable electronic reconfigurability, e.g., p-i-n diodes, varactor diodes, or microelectromechanical systems (MEMS). In addition, some models with the capability of controlling the wavefront polarization modes are also included herein since these are the base of hybrid transmitarrays, i.e., transmitarray with both electronic beamsteering and polarization control. Finally, all the models are compared against each other in order to highlight their benefits and limitations, summarizing their main characteristics, such as the frequency of operation and bandwidth, insertion loss, physical dimensions, and maximum beamsteering range, when available.

Oil-paper insulation as an irreplaceable insulation system in the electrical power transformer is inevitably suffering the water intrusion on working condition, which will make dielectric performance degraded and insulation aging accelerated. In high interest of explaining the deterioration effect of absorbing moisture on the dielectric properties of oil-paper insulation system and corresponding mechanism, the space charge and trap level characteristics are investigated for the specially prepared oil-impregnated pressboards with different moisture contents. The Pulsed Electro Acoustic and Isothermal Surface Potential Decay experiments are performed to test the space charge distributions and evaluate the trap level depths, respectively. It is indicated that the polarity of injected space charges is alternated with the decaying rate being raised when the absorbing moisture is aggravated in oil-impregnated pressboards. The charge carriers are more prone to be captured by the shallow-level traps that have been introduced by water permeation near pressboard surface than the intrinsic deep-level traps inside pressboard. The captured charge carries accounts for the significantly exacerbated space charge accumulation as manifested by the surface charges of oil-impregnated pressboards.

Frequency domain spectroscopy (FDS) technique is widely applied in the condition assessment of the oil-paper system in power transformers. However, the synergistic effect generated by moisture and temperature on the FDS data cannot be analyzed by the existing model since the single independent variable (moisture or temperature) is considered in the construction of the model. To quantify such the synergistic effect, a novel method that utilized for normalizing (or standardizing) the FDS curve is reported based on the theory of the power series and fitting analysis. The present findings reveal that the reported method is capable of predicting the dielectric loss (tan $\delta$ ) curve under diverse test conditions, in which the average error is less than 7%. The synergistic effect can be also explored by using the extracted feature parameters. The potential application is then proved to make up for the measurement errors during the FDS test, the findings are expected to promote the moisture analysis of the transformer insulation.

In this short paper, our main objective is to construct binary locally repairable codes (LRCs) with good properties. Two constructions of LRCs with short lengthes are proposed. The first one is that define a u-linearly independent set (u-LIS) of an LRC with disjoint repair groups (DRGs) and enlarge it into another one with bigger size to construct new LRCs. The second is puncturing check matrices of known codes to construct new LRCs. As an application, many new binary LRCs are constructed from distance optimal linear codes, which are also locality optimal according to the Cadambe-Mazumdar (C-M) bound.

For current steganalysis of the image content-adaptive steganography, there are multiple problems to be improved, such as high difficulty and low accuracy, when detecting images with various contents and textures. For this problem, an improved steganalytic method is proposed in this paper based on the pre-classification and feature selection. First, using the features extracted based on the dependency analysis of image adjacent data, the images with various content and texture complexities are pre-classified as multiple clusters by the K-means algorithms. Then, the performance of existing various steganalytic features are analyzed for different clusters of images, and the optimal features for each cluster are selected for final classification. The experimental results show that the detection accuracy could be improved by the proposed method, and the rationality and availability are also verified. At the same time, the analysis and experimental results in this paper also show that the images with rich content and complex texture should be paid more attention both in steganography and in steganalysis.

Power transformers are considered as one of the main parts of any power system. Because of their importance and high cost, it is important to check the state of the insulation system inside them from time to time. Dissolved gas analysis test as well as Furan compounds analysis has been widely used as recommended methods to assess the transformer insulation system state. This paper introduces an empirical form that can predict the degree of polymerization of the paper insulation system inside the transformer by measuring Furan compounds. This proposed empirical form is validated by comparing its results with other methods reported in the literature in two different case studies. Subsequently, the proposed formula is used to predict the lifetime and the insulation system state of a transformer that operates in Abo Sultan steam power plant in Egypt. The 2-FAL had been measured five times for this transformer in the period between 2013 and 2015. Depending on these five measurements, an equation that can predict 2-FAL level inside this transformer in relation to its age has been proposed. This proposed equation is validated by comparing the measured and estimated 2-FAL in the period between 2016 and 2019. According to the attained results, it was found that the insulation system inside the investigated transformer seems to face a serious problem and this transformer cannot remain in service after 2027. Finally, the paper introduced a general technique that can be used for any transformer in order to predict its remaining lifetime.

Recently, it has been shown that channel feedback helps to enhance the physical layer security (PLS) of communication systems. The current use of feedback focuses on generating secret keys protecting the transmitted messages, and this feedback scheme is proved to be optimal for some physically degraded channel models. In this paper, we revisit the model of the state-dependent wiretap channel with the noncausal state at the transmitter, which plays an important role in the PLS of the wireless communication systems. We propose a new feedback scheme for this model and show that the proposed new scheme performs better than the already existing secret key-based feedback scheme. The results of this paper are further explained via a Gaussian example.

The ReaxFF molecular dynamics simulation and Monte Carlo method were adopted to analyze the pyrolysis process of cellulose in insulating papers from the perspective of microscopic atom. Molecular dynamics failed to continuously describe the motion behavior of an atom. According to this principle, the system can only calculate the atomic state on the node and then move the atom by a time step to continue calculating the atom. This paper would put forward the optimal step setting method of cellulose thermal decomposition in insulating paper: setting one step every other 0.1 fs. Specifically, for small molecules with a simple structure, such as H2O, the step size was set to 0.4 fs or less, while the step size of macromolecules with complex structures (CH2O2) should be set to 0.2 fs or less. In addition, the relationship between the step size and the temperature to which the system was heated was given as well in this paper. In previous literatures, empirical values were used to set the step size. This study would not only provide a theoretical basis for the study on the bond formation and fracture process of cellulose pyrolysis products, but also offer the data and guidance for related fields in the future, thus rendering an efficient simulation process.

In general, considering standard production, as well as coconut oil production, in oil consumption industries is an important factor. Oil color is an important element, as it is an important factor for consumers or buyers in selecting coconut oil. In the process of producing coconut oil, the cold-pressed method has been chosen to maintain the essential quality of coconut oil. The quality of the coconut oil is inspected from the production process by means of light passing through the coconut oil. Then, the production staff compares the turbidity of coconut oil with the master sample. The turbidity of coconut oil in every production must be compared with a master sample to maintain standards control. According to previous studies, there are many methods for determining coconut oil turbidity. One method that has been utilized is determining turbidity from light passing through the medium in which the transmitted light can be absorbed through the turbidity of the variable medium. This process is applied together with image processing to determine the coconut oil turbidity. In this research, we propose a method for measuring coconut oil turbidity by the Moving Average Median of Hue (MAMoH), which is better in detecting the coconut oil turbidity than the Median of Gray Scale (MoGS) method, Median of Hue (MoH) method, and Random Position Median of Hue (RPMoH) method. In terms of the percentage accuracy of the efficiency test; the MAMoH method has 99 percent accuracy, while the MoGS method is not applicable, the MoH method has 88.04 percent accuracy, and the RPMoH method has 85.91 percent accuracy. Thus, the MAMoH method is considered an appropriate method for measuring coconut oil turbidity.

The production index of gold cyanidation leaching process has an important influence on the economic benefits of the plant-wide hydrometallurgical process. In the actual leaching production process, due to the fluctuations of the previous procedure, the leaching process is often affected by the uncertainty and process disturbance. And hence, the prediction accuracy of the traditional point prediction models (such as ANN: Artificial Neural Network) decreases seriously and cannot provide any quantified information about the uncertainty or process disturbance. To solve the above problem, the interval prediction technique based on Radial Basis Function (RBF) ANN is proposed and used to model a gold cyanidation leaching plant encountering uncertainty and process disturbances in this paper. The objective function trained in the interval prediction model is not based on the prediction error, but the comprehensive measure index, namely, the coverage width criteria, which consists of the prediction interval coverage probability and the prediction interval normalized averaged width. Compared to the traditional point prediction, when the process uncertainty and disturbances are present, the interval prediction model will provide more helpful process information to the operators or process designers for determining further optimization and control strategies. The simulation and practical application results show that most of the real values of gold recovery can be covered between the upper and lower bounds with a predefined probability, which indicates the effectiveness and reliability of the interval prediction model, thus laying an important foundation for plant-wide optimization and control.

This paper examines the history of electrical engineering education, leveraging the concept of “expansive (dis)integration” to frame a number of key trends and challenges in the field. Our account is organized historically, starting with the origins and early development of electrical engineering education beginning in the late 1800s, and then tracing out the rise of new subfields and specialties during the inter-war and post-WWII periods. The development of computer engineering as a field is given special attention as a case study in disciplinary (dis)integration, while setting the stage for a discussion of broader trends associated with the rising influence of digital techniques and technologies across electrical engineering. The final sections of this paper report on some contemporary challenges and opportunities that may further transform the field in upcoming years and decades, with particular emphasis on issues of demographic diversity and perceptions of broader relevance and impact. The approach of this paper is largely historical, drawing on a wide variety of primary and secondary source materials. It is expected that this paper will be of interest to anyone who would like to know more about the historical development of electrical engineering education, including in relation to more contemporary currents in the field.

Formaldehyde is one of the indoor air quality pollutants produced by indoor decoration. The World Health Organization has listed Formaldehyde as a primary carcinogen. Wood planks for house interior decoration are common sources of formaldehyde. Based on the technology research and development of monitoring and control of the smart home, the air quality should be effectively improved through emission and suppression. This study uses extremely unventilated student renters in Taiwan as simulation spaces. Two classes of wood plank construction materials, F1 and F3, which are classified according to as different concentrations of formaldehyde standard board grades by Taiwanese. Through three different temperature control experiments, each group of experiments use electrochemical formaldehyde detectors to measure at least two consecutive days of data to analyze the influence to which temperature, the control factor, affected formaldehyde emission rate. The results revealed that the F3 class wood planks can increase the rate of formaldehyde emission through heating, which has a significant effect on home environment control, but they need a temperature below 10 °C to barely maintain within the regulations in Taiwan. The F1 class wood planks have an emission rate of nearly zero in a low-temperature environment due to its low formaldehyde emission. The emission rate of the F1 in a high-temperature environment is not as effective as the F3. The addition of experimental data can be used as a reference basis for AI decision making, which is conducive to the establishment of indoor intelligent control systems.

Abandoned mineral management has become an important global issue, and the collection, recycling, and disposal of mineral processing tailings (MPT) is critical in both mining engineering and environmental protection. In this study, flocculation sedimentation experiments and slurry rheological tests were carried out with unclassified tailings, and the flocculation sedimentation behaviour of the tailings under different conditions was investigated. The experimental results showed the followings: (1) Under close sedimentation effect conditions, different flocculants showed different effects on the fluidity of the slurry underflow, which was used as an important basis for optimization of the flocculation effect. (2) A tailings solid mass concentration of 40% and a flocculant dosage of 25 g/t were obtained as preferable sedimentation conditions. (3) Based on a microparticle agglomeration characteristics tests at the initial stage of flocculation, a flocculation concentration kinetic model was established that conformed to the fractal characteristics of the particles, which improved the applicability and accuracy of the concentration kinetic equation and the characteristic variables. In this study, an objective method for determining the parameters of full tailings flocculation sedimentation was realized. The results of an industrial trial operation also verified the reliability of the preferred parameters, which provided an effective basis for refined control of an efficient tailings recycling process.

This paper deals with investigating the closed-loop stability boundary of the highly flexible aircraft with structural flexibility and input saturation constraint. A method is presented to analyze the stable region based on the system features of the open-loop instability. In this paper, a dynamic model of highly flexible aircraft is made and the dynamic characteristics are analyzed and the long period mode and stability are investigated in terms of the trimmed model. Considering the saturation constraint of elevator deflection, the closed-loop stability boundary of the system under saturation constraint is discussed by combining the open-loop instability features of highly flexible aircraft. The analysis indicates that the boundary is related to the left eigenvector consistent with the amplitude constraint and the unstable poles of the control signals. Based on the long period instability of the aircraft, the formula of closed-loop stability boundary is analytically obtained. The convergence region of highly flexible aircraft is verified in terms of the LQR controller. The influence of structural flexibility and saturation constraint amplitude of elevator on the stability boundary of highly flexible aircraft is analyzed based on state constraints, which is also compared with the rigid aircraft. The simulation results show that the closed-loop stability of the system is restricted by the open-loop characteristic of the system and the control input saturation constraint.

The airway tree is one of the most important part in human respiratory system. Airway segmentation plays a crucial role in pulmonary disease diagnosis, localization and surgical navigation. We propose a novel method to improve airway segmentation in thoracic computed tomography(CT) using deep learning. In order to take into account the multi-scale changes of the airway and achieve accurate airway segmentation, we design an end-to-end Tiny Atrous Convolutional Network (TACNet) based on 3D convolution neural network. In view of the difficulty of classification due to the numerous branches of airway, two evaluation factors, namely, the angle of airway bifurcation and the buffer length of airway bifurcation are designed, which are used for airway classification by combining the centerline extraction. We train TACNet on the inspirator thoracic CT scans with ground truth, which are generated by clinicians and evaluate on our own clinical data sets and EXACT’09 data sets. Compared with state-of-the-art airway segmentation algorithms, proposed algorithm in this paper achieve very competitive results in 20 test datasets of the EXACT’09 challenge. The experimental results show that the algorithm proposed in this paper has high robustness and advantages regardless of airway segmentation or airway classification. In 20 test datasets of the EXACT’09 challenge, the average airway tree length detection rate is the best in the public literatures.

This paper tackles the problem of detecting incongruities between headlines and body text, where a news headline is irrelevant or even in opposition to the information in its body. Our model, called the graph-based hierarchical dual encoder (GHDE), utilizes a graph neural network to efficiently learn the content similarity between news headlines and long body paragraphs. This paper also releases a million-item-scale dataset of incongruity labels that can be used for training. The experimental results show that the proposed graph-based neural network model outperforms previous state-of-the-art models by a substantial margin (5.3%) on the area under the receiver operating characteristic (AUROC) curve. Real-world experiments on recent news articles confirm that the trained model successfully detects headline incongruities. We discuss the implications of these findings for combating infodemics and news fatigue.

The aim of this paper is to design, analyze and optimize the “Multi-Stack Slotless Axial Flux Switching Permanent Magnet Machine”. In the design process, mathematical models are implemented, and the Finite Element Method (FEM) is performed to analyze the machine performances. The paper aims to minimize the occurrence of cogging torque and torque ripple in the multi-stack slotless stator AFPM machine. As a consequence, it reduces the vibrations in the machine and increases its life span. Multi-stack slotless stator AFPM machine with a right-angled trapezoid-shaped PM is proposed and comparison is done with conventional shape AFPM machine. In order to examine the performance of multi-stack slotless stator AFPM machine Finite Element Analysis (FEA) is used. To further enhance the characteristics of the designed machine with the proposed right-angled PM shape, optimization is done by considering inner and outer pole pitch as the design variables. In optimization process, krigging method assigned with Latin Hyper-cube Sampling and a genetic algorithm (GA) is performed due to suitability with non-linear data. Then, finite element analysis by JMAG-Designer is performed to verify the results. It is determined that optimized model has achieved 65% reduction in torque ripples as compared with the conventional design. Hence, this work attempts to optimize the performance of the AFPM machine.

This paper reveals the fundamental reason for the asymmetrical issue in magnetic-geared machines (MGMs) based on flux modulation theory. The analysis indicates that the magnetic circuits of three-phase windings in MGMs are inherently asymmetrical. This asymmetrical issue is even more severe in conventional consequent-pole MGMs (CP-MGMs) because of the more distorted magnetic field. Hence, to address the asymmetrical issue, a novel structure featuring enhanced harmonic elimination capability is proposed in this paper. Consequently, torque density can also be improved. In particular, the proposed CP-MGM employs modular structure and axially embedded permanent magnets (PMs) to achieve symmetrical back electromotive force (EMF) waveforms and improved torque capability, respectively. To further improve the electromagnetic performance of the proposed CP-MGM, the PM arc ratio and flux modulator width ratio are analytically designed, which provides a general design guideline for CP-MGMs. To illustrate the merits of the proposed CP-MGM, a few other MGMs are included for a fair comparison based on finite element analysis (FEA). Results show the proposed CP-MGM can achieve more symmetrical back EMF waveforms and lower torque ripple, as well as lower PM consumption and higher torque density, as compared with its MGM counterparts. Published version Schaeffler Group Research Grant M4062765.040.601001

An intrusion detection system (IDS) is an important protection instrument for detecting complex network attacks. Various machine learning (ML) or deep learning (DL) algorithms have been proposed for implementing anomaly-based IDS (AIDS). Our review of the AIDS literature identifies some issues in related work, including the randomness of the selected algorithms, parameters, and testing criteria, the application of old datasets, or shallow analyses and validation of the results. This paper comprehensively reviews previous studies on AIDS by using a set of criteria with different datasets and types of attacks to set benchmarking outcomes that can reveal the suitable AIDS algorithms, parameters, and testing criteria. Specifically, this paper applies 10 popular supervised and unsupervised ML algorithms for identifying effective and efficient ML-AIDS of networks and computers. These supervised ML algorithms include the artificial neural network (ANN), decision tree (DT), k-nearest neighbor (k-NN), naive Bayes (NB), random forest (RF), support vector machine (SVM), and convolutional neural network (CNN) algorithms, whereas the unsupervised ML algorithms include the expectation-maximization (EM), k-means, and self-organizing maps (SOM) algorithms. Several models of these algorithms are introduced, and the turning and training parameters of each algorithm are examined to achieve an optimal classifier evaluation. Unlike previous studies, this study evaluates the performance of AIDS by measuring the true positive and negative rates, accuracy, precision, recall, and F-Score of 31 ML-AIDS models. The training and testing time for ML-AIDS models are also considered in measuring their performance efficiency given that time complexity is an important factor in AIDSs. The ML-AIDS models are tested by using a recent and highly unbalanced multiclass CICIDS2017 dataset that involves real-world network attacks. In general, the k-NN-AIDS, DT-AIDS, and NB-AIDS models obtain the best results and show a greater capability in detecting web attacks compared with other models that demonstrate irregular and inferior results.

In the past few years, game randomizers have become increasingly popular. In general, a game randomizer takes some aspect of a game that is usually static and shuffles it somehow. In particular, in this paper we will discuss the type of randomizer that shuffles the locations of items in a game where certain key items are needed to traverse the game world and access some of these locations. Examples of these types of games include series such as The Legend of Zelda and Metroid. In order to accomplish this shuffling in such a way that the player is able to reach the end of the game, some novel algorithms in graph theory must be utilized, where the game world and its item locations are represented as a graph and each edge on the graph has some rule for which items are required to traverse it. In this paper, we define these algorithms formally and evaluate them with different metrics that can guide a developer’s decision about which algorithm works best for their game.

The simple rules that govern the interactions between the different components of a complex system often lead to interesting behaviours that are unexpected. The experiments described in this paper involved creating a variation of a traditional Braitenberg Vehicle, by placing sensors on ten different possible locations on a simulated vehicle, and incorporating an obstacle avoidance behaviour using a subsumption-like architecture, which resulted in different unusual and unexpected behaviours being produced. The vehicle was allowed to explore a simulated environment which contained a single bright light in the centre with walls on the border. By using a novel combination of the Prediction by Partial Matching compression algorithm and ${k}$ -means clustering, interesting emergent behaviours were effectively discovered within a search space of over 10,000 simulations produced from a simple interaction of light and proximity sensors on a vehicle and a single light source. The clustering algorithm discovered five distinct behaviours: circling and spiralling behaviours; interesting behaviours creating intricate rose petal-like structures; behaviours that create simple rose petal-like structures; behaviours with large movements and low complexity; and behaviours with less movement. The novel algorithm demonstrated in this paper has useful potential in the science of complex systems and modelling to help expedite the systematic exploration of a substantial search space of simulations in order to discover interesting behaviours.

Near-infrared spectroscopy (NIR) has become one of the most important methods for counterfeit drugs identification for its low cost, non-destructive, and on-site detection. However, it is often invalid for unknown samples beyond the scope of modeling samples, as well as it is not efficient in conditions of insufficient samples (insufficient number of samples within the class), unbalanced samples (large difference in the number of samples between classes), and sensitivity of identification results (different tolerance for different errors in application scenarios). To solve these problems, this paper proposes a general method for on-site identification of counterfeit drugs based on Siamese-network modeling with near-infrared spectroscopy, which especially constructs the train set and test set, learning the general knowledge of spectral differences to identify the different drugs by a costumed one-dimensional convolution neural network (1D-CNN), and finally answered the question of whether the on-site two spectra are pointed to the same drug. Based on experimental modeling samples of 1314 spectra, which are involved 9 drugs produced by 25 manufacturers, this paper has constructed and fully trained its model. Then, not known at the time of modeling, 4 drugs produced by 9 manufacturers are used for testing in the on-site application, and the accuracy rate amounts to 97.3%. For generalizing consideration, randomly divided into training and testing categories, the 32015 spectra of 135 drugs produced by 391 manufacturers in the spectral library are handled by the same processing. The generalization model is equally applicable, and the accuracy is above 97%. Compared with traditional binary classification identification methods such as SVM, PLS-DA, Auto-encoding, and one class (OC) threshold identification algorithms such as SVM-OC, SIMCA, conformity test (CT), the proposed method has the best identification ability for unknown samples in modeling.

Handwritten mathematical expressions are an essential part of many domains, including education, engineering, and science. The pervasive availability of computationally powerful touch-screen devices, similar to the recent emergence of deep neural networks as high-quality sequence recognition models, result in the widespread adoption of online recognition of handwritten mathematical expressions. Also, a deeper study and improvement of such technologies is necessary to address the current challenges posed by the extensive usage of distance learning, and remote work due to the world pandemic. This paper delineates the state-of-the-art recognition methods along with the user's experience in pen-centric applications for operating with handwritten mathematical expressions. Recognition methods have been categorized into classes, with a description of their merits and limitations. Particular attention is paid to end-to-end approaches based on encoder-decoder architecture and multi-modal input. Evaluation protocols and open benchmark datasets are considered as well as the comparison of the recognition performance, based on open competition results. The use of handwritten math recognition is illustrated by examples of applications for various fields and platforms. A distinctive part of the survey is that we also considered how UI design relies on the use of different recognition approaches, which is aimed at helping potential researchers improve the performance of the introduced approaches toward the best responses in practical applications. Finally, this paper presents the prospective survey of future research directions in handwritten mathematical expression recognition and their applications.

In the past few decades, although people have conducted in-depth research on community detection in one-mode networks, community detection in bipartite networks has not been extensively researched. In this paper, we propose an improved artificial bee colony algorithm named IABC-BN, which is used to detect the communities in two-mode graphs (i.e. bipartite graphs) with two kinds of vertices in the cluster (i.e. community). Firstly, this paper proposed a novel population initialization process of artificial bee colony (ABC) method for two-mode graph cluster identification. This initialization method can improve the diversity of initial population of ABC and speed up its convergence rate. Secondly, in the employed bee search step of the algorithm, a new combinatorial search equation is proposed. This equation is guided by the global optimal solution and the better neighbour solution of the current solution. By using this combination equation and the increased parameter perturbation frequency, the exploitation ability of the algorithm is further enhanced. Thirdly, in the onlooker bees step, another new combination search equation is also proposed. This equation improves the exploitation level of the algorithm, and an opposition based studying method is employed to promote the exploitation ability of the algorithm. Lastly, in scout bee stage, a probability threshold $\beta $ is introduced to enhance the exploration ability of the algorithm and improve the population diversity of the algorithm. To our knowledge, the IABC-BN method presented in this paper is the first ABC method used to cluster identification in two-mode graphs with two kinds of vertices in the cluster. For verifying the accuracy of the results of the proposed method, a large number of experiments are carried out making use of synthetic bipartite graphs and real bipartite graphs. The test outcomes show that this algorithm is an excellent algorithm for cluster discovery in two-mode graph.

We address the problem of depth estimation from a single monocular image in the paper. Depth estimation from a single image is an ill-posed and inherently ambiguous problem. In the paper, we propose an encoder-decoder structure with the feature pyramid to predict the depth map from a single RGB image. More specifically, the feature pyramid is used to detect objects of different scales in the image. The encoder structure aims to extract the most representative information from the original image through a series of convolution operations and to reduce the resolution of the input image. We adopt Res2-50 as the encoder to extract important features. The decoder section uses a novel upsampling structure to improve the output resolution. Then, we also propose a novel loss function that adds gradient loss and surface normal loss to the depth loss, which can predict not only the global depth but also the depth of fuzzy edges and small objects. Additionally, we use Adam as our optimization function to optimize our network and speed up convergence. Our extensive experimental evaluation proves the efficiency and effectiveness of the method, which is competitive with previous methods on the Make3D dataset and outperforms state-of-the-art methods on the NYU Depth v2 dataset.

Effective shared autonomy requires a clear understanding of driver's behavior, which is governed by multiple psychophysiological and environmental variables. Disentangling this intricate web of interactions requires understanding the driver's state and behaviors in different real-world scenarios, longitudinally. Naturalistic Driving Studies (NDS) have shown to be an effective approach to understanding the driver's state and behavior in real-world scenarios. However, due to the lack of technological and computing capabilities, former NDS only focused on vision-based approaches, ignoring important psychophysiological factors such as cognition and emotion. The main objective of this paper is to introduce HARMONY, a human-centered multimodal naturalistic driving study, where driver's behaviors and states are monitored through (1) in-cabin and outside video streams (2) physiological signals including driver's heart rate and hand acceleration (IMU data), (3) ambient noise, light, and the vehicle's GPS location, and (4) music logs, including song features such as tempo. HARMONY is the first study that collects long-term naturalistic facial, physiological, and environmental data simultaneously. This paper summarizes HARMONY's goals, framework design, data collection and analysis, and the on-going and future research efforts. Through a presented case study, we first demonstrate the importance of longitudinal driver state sensing through using Kernel Density Estimation Methods. Second, we leverage the application of Bayesian Change Point detection methods to demonstrate how we can identify driver behaviors and responses to the environmental conditions by fusing psychophysiological information with features extracted from video streams.

This paper discusses a novel fault location approach using single ended measurement. The natural dissipation of the circuit parameters are considered for fault location. A relationship between the damped natural frequency of oscillation of the transmission line current and fault location is established in this paper. The hybrid dc circuit breaker (dcCB) interrupts the fault current and the line current attenuates under the absence of any driving voltage source. The line capacitance discharges into the fault at a specific frequency of oscillation and rate of attenuation. Utilizing this information, the fault location in a multi-terminal direct current (MTdc) network can be predicted. A three terminal radial model of a MTdc is used for performance evaluation of the proposed method using Power System Computer Aided Design (PSCAD)/Electromagnetic Transients including dc (EMTdc)., 8 pages, 12 Figures, 6 Tables

Industry 4.0 is a revolution in manufacturing by introducing disruptive technologies such as Internet of Things (IoT) and cloud-computing into the heart of the factory. The resulting increased automation and the improved production synergy between stocks, supply chains and customer demands, come along with the threats and attacks from the Internet. Despite extensive literature on the cybersecurity topic, many actors in manufacturing factories are just realizing the impact of cybersecurity in the preservation of their business. This paper introduces step-by-step the concepts and practical aspects of an Industry 4.0 manufacturing factory that are related to cybersecurity. Based on a subdivision of a typical factory into several generic perimeters, we present the vulnerabilities and threats regarding the network and devices usually found in each perimeter. Therefore, it is more efficient to present the recent proposals of the literature regarding cybersecurity guidelines and solutions in Industry 4.0. Instead of spreading a lot of references regarding every aspect of cybersecurity, we focused on a limited number of papers among the recent references. However, for each paper, we provide the details about the purpose of the proposal, the methodology adopted, the technical solution developed and its evaluation by the authors. These solutions range from classical cybersecurity countermeasures to innovative ones, such as those based on honeypots and digital twins. In order to deliver a review also useful to non scientists, we present our guidelines along with those of some organizations involved in cybersecurity harmonization and standardization in the world.

In this paper, a modified COMSOL Multiphysics model with artificial stability is adopted, and the boundary condition developed in the previous paper are applied to the calculation of the photoionization rate. The main processes involved in air discharge were simulated by 39 plasma chemical reactions composed of 12 kinds of particles. The characteristics of low-temperature sub-atmospheric pressure air discharge under unipolar square wave pulse voltage with 13kV applied amplitude, 25 kHz-50 kHz frequency and a duty cycle of 50%-75% are discussed. The results show that: When the duty cycle increases, the average density of electron, N2+, N4+, O2+, O4+, and N2O2+ show an increasing trend, and the average electron temperature changes little; When the frequency increases, the average electron density, the average density of N4+ and O4+ show a downward trend, the average density of N2+, O2+, N2O2+ change little; The average electron temperature shows an increasing trend, but the duration of high electron temperature becomes shorter. When discussing a single period, it is found that the potential difference between the electrode and the plasma determines the direction of the electric field in the space. For the photoionization reaction, even if its influence on the negative streamer is not important, it still needs to be considered in the simulation. The effect of temperature on discharge is also taken as the research emphasis, it includes the following aspects: Firstly, at low temperature, the collision reaction and attachment reaction rates are increased, while the recombination reaction rate is almost unaffected; Secondly, low temperature results in the decrease of secondary electron emission coefficient, which indirectly increases the electric field gradient and the peak value of electric field; Finally, at low temperature, the mobility of carriers, including electrons, positive and negative ions, is increased, but the streamer velocity is decreased.

This paper proposes a linear compensator algorithm to improve the performance of an absolute multipolar magnetic encoder (AMPME). An AMPME is an absolute magnetic rotary encoder that uses a multipolar magnet (MPM) to increase the resolution. The resolution can be dramatically increased in proportion to the number of poles in the MPM. However, various hardware problems that occur during the encoder manufacturing process degrade the AMPME performance. Also, harmonic components occur in the raw data due to various problems, such as the resistance error of the analog circuit, magnetic field overlap between the magnets, position error between the sensor and magnet, and pole-pitch difference. In particular, during the magnetization process of the MPM, the pole-pitch difference becomes a problem when the sizes of each pole are not uniform. This problem causes harmonic components that reduce the absolute position accuracy. To solve these problems, this paper proposes a linear compensation method. The proposed linear compensator consists of two parts. The first part is the enhanced ratiometric linearization for phase calculation and calibration. The second is the phase compensator for removing the phase difference via the pole-pitch difference of the MPM. The linear compensator improves various parameters by precomputing the offset, amplitude, and phase corrections. After compensating for sinusoidal signals, the linear compensator applies appropriate parameters at the appropriate times. This method is faster, easier to set up, and more accurate than the conventional method. Furthermore, this method is experimentally verified against the existing harmonic rejection method. Experimental results are provided to verify the effectiveness of the proposed method.

The Internet of Things is based on a communication network to automatically receive various information from the natural world. It uses intelligent objects with perception, communication and computers to automatically receive various information from nature. All independently managed physical objects are connected to each other to achieve integrated perception, reliable transmission and intelligent processing, and to establish intelligent information between people and objects, and objects and object service systems. This article mainly introduces the impact of industrial agglomeration on the regional economy in a simulated intelligent environment based on machine learning. This paper proposes a method to detect industrial agglomeration index to analyze industrial agglomeration. Through the establishment of the industrial agglomeration index system, the level of integration of the manufacturing industry in our city was objectively analyzed, and the impact of the integration of manufacturing industry on our city was tested empirically. Finally, the relationship between industrial integration and regional economic development was tested. The experimental results in this paper show that industrial integration in a smart environment based on simulation learning has a significant positive impact on regional economic development. Among them, the level of cooperation between the manufacturing service industry and the manufacturing industry increased by 1%, and the level of regional economic development increased by 0.025%.

The individual-machine-equal-area-criterion method already shows potential in the transient stability assessment of multimachine systems. This two-paper series systematically analyzes the transient characteristics of the system trajectory from a genuine individual-machine transient energy perspective. In the first paper, the stability property that characterizes a critical machine is investigated by defining the residual kinetic energy, which only occurs at the maximum individual-machine potential energy point. We indicate that the transient energy conversion inside a critical machine can delineate the trajectory stability of the machine. In this way, the mapping between individual-machine kinetic energy and individual-machine trajectory can hence be established. Simulation results show that the individual-machine transient energy describes the system trajectory more precisely than the superimposed global transient energy in terms of transient stability analysis, and we also demonstrate that the conjecture in early individual-machine studies might fail in special simulation cases.