Search

Spider silk fibers, collected from Pholcus Phalangioides spider were used as a template for obtaining magnesium oxide (MgO, periclase) as well as magnesium hydroxide (Mg(OH)2, brucite) fibers. Magnesium oxide fibers were obtained in a simple manner by heat induced decomposition of magnesium salt (MgCl2) in the presence of the spider silk fibers, while magnesium hydroxide fibers were synthesized by hydration of MgO fibers at 50, 70 and 90 C, for 48 and 96 h. According to Scanning electron microscopy (SEM), dimensions of spider silk fibers determined the dimension of synthesized MgO fibers, while for Mg(OH)2 fibers, the average diameter was increased with prolonging the hydration period. The surface of Mg(OH)2 fibers was noticed to be covered with brucite in a form of plates. X-Ray diffraction (XRD) analysis showed that MgO fibers were single-phased (the pure magnesium oxide fibers were obtained), while Mg(OH)2 fibers were two- or single-phased brucite depending on incubation period, and/or incubation temperature. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 45012]

A new, simple, rapid, sensitive and selective kinetic spectrophotometric method for Pd(II) traces determination was elaborated in this paper. It is based on the catalytic effect of palladium ions upon the oxidation of methylene blue B (MBB) by (NH4)2S2O8 (APS) in citric buffer (BUF) solution. At the working temperature of 25 C and the wavelength of 662.4 nm, the optimal conditions for palladium determination were found. RSD value was found to be 2.6 to 4.9% for the investigated concentration range of Pd(II). Limit of detection (LD) was found to be 2.0 ng cm–3 Pd(II), and limit of quantification (LQ) is 6.9 ng cm–3 Pd(II). Only the presence of Pb2+, Hg2+ and Sn2+ in the reaction mixture interferes the determination of palladium by this method, while Au3+ and Ag+ have the catalytic effect upon the reaction rate. By this method, it is possible to determine the Pd(II) traces in the concentration range of 3.3x10–8 to 1.0x10–6 g cm–3. The method was confirmed by determination of Pd(II) traces in alloy PtRhG as well as in the powder of Pt. The obtained results were compared to those obtained by ICP-OES method and good agreement of results was found. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 172051]

Titania based catalyst and TiO2 doped with zirconia were prepared by modified sol–gel method. The synthesized catalysts samples were characterized by BET, XRD, SEM and FTIR techniques. Photocatalytic activity was tested in the reaction of crystal violet (CV) dye decolorization/decomposition under UV light irradiation. The effect of several operational parameters, such as catalyst dosage, initial dye concentrations, duration of UV irradiation treatment and number of reaction cycles were also considered. The obtained results indicated faster dye decolorization with the increase of the catalyst amount and a decrease of initial CV concentrations. An influence of doping with zirconia on the physico-chemical properties of bare titania was studied. The doping procedure had affected photocatalytic properties of the final catalytic material, and had improved photocatalytic performances of doped catalyst on crystal violet decolorization/degradation in comparison to bare titania. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 1612008, Grant no. 45012 and Grant no. 172061]

Heterogeneous catalysis is in recent focus of research for biodiesel production from vegetable oils because of advantages such as easy separation and reuse of catalysts, although homogeneous catalysis is most commonly used method. The aim of this study was preparation of γ-Al2O3 support by modified sol-gel procedure, synthesis of the KI/Al2O3 catalyst and testing its activity in the transesterification of sunflower oil with methanol. Influences of different process parameters on conversion of sunflower oil to methyl esters were examined. The gained results implicate that the potassium iodide incorporation into/onto the structure of γ-Al2O3 significantly influences textural and structural properties of the catalyst. Additionally, the catalyst basic strength is increased and all together those properties are positively affecting the activity of the catalyst in the reaction of transesterification of sunflower oil with methanol. The impregnation of alumina with potassium iodide resulted in the additional formation of basic catalytically active sites. The surface properties of the catalyst have an essential impact on its catalytic performance. Under relatively mild process conditions and relatively short reaction time, the usage of the KI/Al2O3 catalyst resulted in very high conversion to fatty acids methyl esters (i.e. 99.99 %). [Projekat Ministarstva nauke Republike Srbije, br. 172061 i br. TR 34008]

The influence of the physicochemical properties of a series of CaO catalysts activated at different temperatures on the biodiesel production was investigated. These catalysts show dissimilar yields in the transesterification of triglycerides with methanol. We have found significant relationships between structural properties (the type of the pore system, the typical CaO crystal phase and the sizes of crystallites (up to 25 nm), the minimal weight percentage of CaO phase, the total surface basicity and potential existence of two types of basic active sites) of CaO prepared and activated by means of thermal treatment at highest temperature and catalytic efficiency. Benefits of this catalyst are short contact time, standard operating temperature and atmospheric conditions, relatively low molar ratios and small catalyst loading. These all together resulted in a very high biodiesel yield of high purity. The properties of different biodiesel (obtained with the use of the prepared CaO catalyst) blends with different diesel and biodiesel ratios indicate that the higher the fraction of biodiesel fuel the better the achieved fuel properties according to the EU standards. A significant reduction of CO2 and CO emissions and only a negligible NOx increase occurred when blends with an increased biodiesel portion was used. The use of biodiesel derived blends, and the eventual complete replacement of fossil fuels with biodiesel as a renewable, alternative fuel for diesel engines, would greatly contribute to the reduction of greenhouse gases emissions. [Projekat Ministarstva nauke Republike Srbije, br. ON 172061 i TR 34008]

The quality of some medicinal plants and their water extracts from South East Serbia is determined on the basis of metal content using atomic absorption spectrometry. The two methods were used for the preparation of water extracts, to examine the impact of the preparation on the content of metals in them. Content of investigated metals in both water extracts is markedly lower then in medicinal plants, but were higher in water extract prepared by method (I), with exception of lead content. The coefficients of extraction for the observed metal can be represented in the following order: Zn > Mn > Pb > Cu > Fe. Correlation coefficients between the metal concentration in the extract and total metal content in plant material vary in the range from 0.6369 to 0.9956. This indicates need the plants to be collected and grown in the unpolluted area and to examine the metal content. The content of heavy metals in the investigated medicinal plants and their water extracts is below the maximum allowable values, so they are safe to use.

This paper presents a complete characterization of rapeseed oil, of Banaćanka variety, as well as the potential use of oil generated after filtering, in order to obtain biodiesel. Researches are based on the fact that Banaćanka is the oldest domestic rapeseed variety, the so-called double zero "00" (low in erucic acid, below 5%, and glucosinolates below than 30 mmol g-1), suitable for use in the region, since it is low temperatures tolerant, posseses high genetic potential for seed yield of about 5.2 t/ha, and high oil content of around 45%. Transesterification was carried out in batch reactor Parr 4520, with KOH as a catalyst. Cold pressed oil without prior treatment was used as feedstock for transesterificataion. The paper analyses the effects of temperature, reaction duration, catalyst amount and rate of agitation on the synthesis of biodiesel at constant pressure and molar methanol/oil ratio.[Projekat Ministarstva nauke Republike Srbije, br. TR-31046: Improvement of the quality of tractors and mobile systems with the aim of increasing competitiveness and preserving soil and environment]

Bentonite is mainly composed of clay minerals from smectite group, therefore it has a well developed and chemically active surface area and high cation exchange capacity. Moreover, an interlayer space of smectite has unusual hydration properties, which manifest as swelling of bentonite in water. These properties make bentonite as a commonly used raw material in chemistry and industry, and it is very important in environmental protection and water treatment as an effective sorbent of heavy metals. The results of X-ray diffraction, a cationic exchange capacity, specific surface area, acid-base properties of the surface and the swelling index showed that the bentonite sample contains mostly montmorillonite. The aim of this study was to test the efficacy of bentonite in the removal of Mn2+ from aqueous systems. The experimental results of Mn2+ adsorption on the bentonite were interpreted by Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherms. The adsorption isotherm studies indicate that the adsorption of Mn2+ follows Langmuir isotherm very well. Theoretical monolayer saturation capacity according to Langmuir model was 12.41 mg/g. The removal of Mn2+ is achieved by ion exchange mechanism with naturally occurring cations in bentonite, as well as by forming the inner- and outer-sphere complexes with bentonite surface.

Cones of the European Black pine and Horse chestnut kernel, regarded as brown municipal waste, was utilized in this work as a precursor for powdered activated carbons. Chemical activation was employed at 500°C in inert atmosphere of nitrogen. Standard physico-chemical analyses were performed to examine obtained products. FTIR method was employed to determine fuctional groups which were found to be typical for activated carbons. Acidic oxygen groups were quantitatively determined using Boehm titrations. It was established that carboxylic groups on pine cone activated carbon, and phenolic groups on chestnut kernel activated carbon were dominant from all acidic oxygen groups. Since both contact pH and pHPZC were determined to be fairly acidic, it could be concluded that obtained activated carbons belong to L-type. Shape and layout of micrometer dimensioned particles were observed by scanning electron microscopy. Particles of different shapes and dimensions along with small cracks and wide crevices and voids were noticed. Textural analysis was used to determine specific surface area and pore distribution of obtained activated carbons. Obtained products possess highly developed surface area and wide pore distribution.

The heavy metals (Fe, Cu, Zn and Mn) contents of selected plant species, grown in Southeast region of Serbia, that are traditionally used in alternative medicine were determined. Among the considered metals, iron content was the highest one and varied from 137.53 up to 423.32 mg/kg, while the contents of Cu, Zn and Mn were remarkably lower, and ranged from 8.91 to 62.20 mg/kg. In addition, an analysis of plants extracts showed a significant transfer of heavy metals during extraction procedure; therefore, the corresponding extraction coefficients reached values up to 88.8%. Those were especially high in the ethanol based extracts. Moreover, it is established that such coefficients mostly depend on the solvent nature and also on the treated plant species. The obtained results impose that medicinal plants from Southeast region of Serbia due to rather low content of heavy metals are appropriate for preparation of teas and medicinal extracts.