Search

Abstract: The paper provides a synthesis of work by the writers that has the objective of developing a new working stress method for the calculation of reinforcement loads in geosynthetic reinforced soil walls. As a precursor to this objective, careful back-analyses of a database of instrumented and monitored full-scale field and laboratory walls are used to demonstrate that the current American Association of State Highway and Transportation Officials (AASHTO) Simplified Method used in North America results in excessively conservative estimates of the volume of reinforcement required to generate satisfactory long-term wall performance. The new design method captures the essential contributions of the different wall components and properties to reinforcement loads. The method is calibrated against measured in situ wall reinforcement loads using a careful interpretation of reinforcement strains and the conversion of strain to load using a suitably selected reinforcement stiffness value. A novel feature of the method is to design the wall reinforcement so that the soil within the wall backfill is prevented from reaching a failure limit state, consistent with the notion of working stress conditions. [Copyright &y& Elsevier]

The paper demonstrates deterministic and reliability-based assessment of strength limit states (tensile resistance and pullout) and the service limit state for soil failure for mechanically stabilized earth (MSE) walls constructed with polyester (PET) strap reinforcement. The general approach considers the accuracy of the load and resistance models that appear in each limit state equation plus uncertainty in the estimate of nominal load and resistance values at time of design. Reliability index is computed using a closed-form solution that is easily implemented in a spreadsheet. Three PET strap MSE wall case studies are used to demonstrate the reliability-based assessment approach and to compare margins of safety using different load and resistance model combinations. In some walls using the Coherent Gravity Method to compute loads, the recommended nominal factors of safety for tensile strength and pullout limit states were not satisfied. However, reliability analyses showed that the walls satisfy recommended minimum target reliability index values for the limit states investigated, usually by large amounts. The most critical limit state is the soil failure limit state which is used in the Simplified Stiffness Method to keep the reinforced soil zone at working stress conditions assumed for geosynthetic MSE walls under operational conditions. • Describes deterministic and reliability-based analyses of internal limit states for PET strap walls. • Reliability index is computed using a closed-form solution that is easily implemented in a spreadsheet. • Three PET strap MSE wall case studies are used to demonstrate the reliability-based assessment approach. • Most critical limit state is the soil failure limit state which is used in the Simplified Stiffness Method. • General approach is applicable to MSE walls with extensible and inextensible reinforcement materials. [ABSTRACT FROM AUTHOR]

The paper reports the details of numerical models used to predict the performance of two 3.6 m-high well-instrumented wrapped-face walls. The walls were nominally identical except that the reinforcement material in one wall was a steel welded wire mesh and in the other a biaxial polypropylene geogrid. The backfill soil was modelled using both linear and nonlinear elastic-plastic constitutive models. A general hyperbolic (nonlinear) axial load-strain-time model was used for the reinforcement. The numerical results show good agreement with measured performance features for the welded wire mesh wrapped-face wall. Agreement between numerical predictions of facing displacements and maximum reinforcement loads was less accurate for the very flexible geogrid wrapped-face wall. The discrepancies are believed to be related to the unusually flexible wrapped face used in the geogrid wall construction. Numerically predicted and measured maximum reinforcement loads are compared to loads using the AASHTO reinforcement strength-based design approach (Simplified Method) and the Simplified Stiffness Method which is an empirical reinforcement stiffness-based method. The paper provides physical test data that can be used to benchmark other numerical models, highlights lessons learned during the development of the models, and identifies reasonable expectations for numerical model accuracy for models of similar complexity used to simulate the performance of mechanically stabilized earth (MSE) wall structures under operational conditions. [ABSTRACT FROM AUTHOR]

Abstract: North American design codes are now committed to the development of load and resistance factor design (LRFD) for reinforced soil structures including internal stability limit states. Reliability-based analysis is required to carry out these calibrations. A framework for LRFD calibration has been proposed by the writers that requires bias statistics for load and resistance terms for each limit state function. In this paper the formulation of the limit state for reinforcement tensile rupture is developed and the component strength-reduction bias statistics identified. The paper describes how to compute bias statistics from project-specific installation damage trials for use in reliability-based design for the reinforcement rupture limit state or using data from multiple sources for LRFD calibration. A database of results from field installation damage trials on 103 different geosynthetic products was collected from 20 different sources. A total of 799 and 2248 in-air tensile test results were reviewed for undamaged and damaged geosynthetic specimens, respectively. This database is used to compute installation damage bias statistics for six different categories of geosynthetic and four categories of backfill soils classified according to the D 50 particle size. A practical outcome is that for analysis purposes, bias statistics can be grouped into two ranges for each geosynthetic type based on D 50 of the soil greater than or less than 19 mm. The paper shows how bias statistics together with load and resistance factors for the geosynthetic rupture limit state function recommended by can be used to calculate probability of failure using Monte Carlo simulation and demonstrates the sensitivity of probability of failure to magnitude of installation damage bias statistics. The installation damage data is valuable for future LRFD calibration to select resistance factors for use in design codes for the geosynthetic rupture limit state in reinforced soil structures. [Copyright &y& Elsevier]