Search

The paper reports the details of numerical models used to predict the performance of two 3.6 m-high well-instrumented wrapped-face walls. The walls were nominally identical except that the reinforcement material in one wall was a steel welded wire mesh and in the other a biaxial polypropylene geogrid. The backfill soil was modelled using both linear and nonlinear elastic-plastic constitutive models. A general hyperbolic (nonlinear) axial load-strain-time model was used for the reinforcement. The numerical results show good agreement with measured performance features for the welded wire mesh wrapped-face wall. Agreement between numerical predictions of facing displacements and maximum reinforcement loads was less accurate for the very flexible geogrid wrapped-face wall. The discrepancies are believed to be related to the unusually flexible wrapped face used in the geogrid wall construction. Numerically predicted and measured maximum reinforcement loads are compared to loads using the AASHTO reinforcement strength-based design approach (Simplified Method) and the Simplified Stiffness Method which is an empirical reinforcement stiffness-based method. The paper provides physical test data that can be used to benchmark other numerical models, highlights lessons learned during the development of the models, and identifies reasonable expectations for numerical model accuracy for models of similar complexity used to simulate the performance of mechanically stabilized earth (MSE) wall structures under operational conditions. [ABSTRACT FROM AUTHOR]

Geosynthetic-reinforced and column-supported (GRCS) embankments have proven to be an effective construction technique for fills on soft foundations. The paper introduces a modified unit cell approach to model GRCS embankments supported by deep mixed column walls. The modified unit cells include linear elastic springs at one or both vertical boundaries to simulate lateral displacements of the embankment fill and foundation soil. The finite difference program FLAC is used to compare numerical outcomes using the modified unit cells with those using the typical unit cell arrangement with lateral rigid side boundaries. Numerical results demonstrate good agreement between simulations using small-strain and large-strain modes in some cases and large differences in other cases. Lateral displacements of the embankment fill and foundation soil using the modified unit cells are shown to have large influence on reinforcement loads. Finally the paper demonstrates that calculated reinforcement loads are sensitive to choice of small-strain or large-strain mode when using program FLAC. [ABSTRACT FROM AUTHOR]

Abstract: Geosynthetic reinforced soil walls and slopes are now a mature technology in geotechnical engineering. Nevertheless, the mechanisms of soil-geosynthetic interaction are not fully understood for pullout of a geogrid material in the anchorage zone of a reinforced structure. It is also difficult to quantify the interactions between the geogrid and the soil. A new strategy to overcome these difficulties is to use a pullout box with a transparent glass bottom, a transparent soil, and non-contact measurement technology. This paper describes such a pullout box apparatus which is used in combination with a recently developed transparent granular soil. Embedded geogrid specimens are visible through the transparent bottom of the box and the surrounding soil. The displacements of the geogrid and seed (target) particles placed in the transparent soil are tracked using digital images captured by a row of synchronized cameras located below the apparatus. Digital processing is carried out using the Digital Image Correlation (DIC) technique to quantify the in-situ displacement of the geogrid specimen and surrounding soil. The displacements are used to compute continuous longitudinal strain profiles in the geogrid specimen over the duration of each pullout test and relative shear displacements between the geogrid and the soil. Also reported are lessons learned to improve the method of clamping geogrid specimens at the front of the pullout box which are also applicable to conventional pullout box equipment. [Copyright &y& Elsevier]

Abstract: The paper describes two constitutive models for the simulation of expanded polystyrene (EPS) seismic buffer shaking table tests previously reported by the writers. The first model is linear elastic–plastic with Mohr–Coulomb criterion and Rayleigh damping. The second is called the equivalent-linear method (ELM) which incorporates hysteretic load–unload cycles using Masing-type functions and strain-dependent shear modulus and damping ratio functions. The constitutive models were applied to both the geofoam buffer and sand backfill in both approaches. Both models are shown to capture qualitative features of measured peak load-time response of the physical tests. The advanced ELM model gave predictions that were closer to the measured results for the seismic buffer test with the most compressible EPS when model accelerations and total wall forces were greatest. However, the simpler model is judged to be sufficiently accurate for practical purposes when the dynamic force increment is considered only. [Copyright &y& Elsevier]