Search

Due to the inherent unpredictability of geological conditions, tunnelling operations are often at risk of encountering water inrushes. Such incidents can lead to construction delays, impose financial strains and pose significant safety threats to the workers involved. Water‐bearing geological formations are the main triggers for such incidents, with factors such as the positioning, water quantity and permeability distribution of these formations being key to predicting the occurrence and severity of water inrush disasters. By leveraging the complex interplay among relaxation time, P‐wave velocity and permeability within the rock's physical properties, a series of indoor tests were conducted on 40 artificial reef limestone cores to extract the necessary parameters. Through the analysis of the data, the comprehensive permeability prediction model was established, and the correlation coefficient was 0.9420 between the model's predictions and actual measurements. At the same time, through theoretical and mechanism analysis, the relationship between permeability and relaxation time and the relationship between permeability and P‐wave velocity were analysed. Finally, 10 natural reef limestone samples were used to verify the accuracy of the model. The prediction model enables an accurate evaluation of tunnel permeability, thus providing a scientific basis for the mitigation of tunnel water inrush hazards. [ABSTRACT FROM AUTHOR]

The present study attempts to combine direct current and induced polarization methods for 3D geological modelling and preliminary volume estimation of gold mineralization targets in the Simi locality, Adamawa, Cameroon. To begin, resistivity and chargeability data were collected along seven profiles oriented in N150E using the electrical tomography technique. A geological investigation was also carried out and allowed in addition to the geological formations to highlight the existence of gold mineralization in the study area. The interpretation of the inversion results was done by taking into consideration the geological field data and the existing resistivity charts. The 3D distribution of the interpreted sections allowed us to make a horizontal correlation between the different sections and to elaborate the 3D geological model of the study area by using the deterministic inverse distance method. The estimated model indicates a volume of 621,130.625 m3 of the possible gold complex. The gold complex was then divided into two mineralization domains based on chargeability ranges (mV/V): A first domain is associated with a major mineralization zone (39–60 mV/V) with a volume of 10,842 m3, and a second domain is associated with secondary mineralization zone (18–39 mV/V) with a volume of 610,288 m3. This model allows to compartmentalize the gold complex and can be used as a base model for the gold investigation in the study area. [ABSTRACT FROM AUTHOR]

This study complements two earlier papers on the interpretation and estimation of post‐stack time‐shifts that detail the most popular measurement methods to date. In this current work, the focus is on describing the magnitude and identifying the origin of the uncertainty present in these time‐shift values. We also consider how the underlying assumptions behind conventional time‐shift estimation methods can contribute to the inadequate resolution of the subsurface time‐lapse changes. The various errors fall into three broad categories: (1) those related to intrinsic data limits that cannot be avoided; (2) those associated with seismic measurement methods that can be corrected with some effort; and finally (3) those that arise due to approximations to the wave physics made during the design or implementation of the methods. In the first category are limitations due to sampling rate and signal‐to‐noise ratio, and wavelet interferences resulting from the narrow band nature of the seismic data and the heterogeneous nature of the geology itself. The effects produce errors of typically a fraction of a millisecond, but exceptionally in 4D data with poor repeatability up to 1 ms. In the second category are acquisition and processing errors. These are usually of the order of a few milliseconds but can reach up to 10s of milliseconds and are, therefore, essential to correct. It is possible to correct the effects of tides and seawater variations in marine acquisition if these changes are monitored and measured. Navigation and timing are identified as issues to consider carefully. For land data, daily and seasonal near‐surface variations are still problematic, and source and sensors must be buried to deliver interpretable time‐shifts. The impact of choices made during processing can be significant but is specific to the workflow and dataset and thus cannot be generically assessed. However, the effects from residual multiples can be identified and treated. Of moderate importance is the third category of errors, which consists of four items. Of these, the effect of lateral image shifts and amplitude effects are judged to play a minor role. Deviation from the assumption of vertical ray‐paths during post‐stack analysis appears to be of concern only for reservoirs with noticeably dipping structures and strong contrasts. The effect of pre‐stack variations on the post‐stack measurements remains a topic to be more thoroughly examined, and the conclusion is unclear. Finally, it is apparent that uncertainties in all categories are strongly dependent on the field setting and geographical location. [ABSTRACT FROM AUTHOR]

The primary focus of this study is to explore the potential mineral areas. Advanced Spaceborne Thermal Emission and Reflection Radiometer images and radiometric data were combined in the Tikirt region to map hydrothermal alteration zones associated with mineralized deposits. Advanced Spaceborne Thermal Emission and Reflection Radiometer images were analysed using band ratios, principal component analysis and a fuzzy logic model to discover argillic, phyllic, propylitic and iron oxide alterations and to generate a mineral prospectivity map. In addition, mono‐element maps of radiometric elements (K in %, eU in ppm, eTh in ppm) and their behaviour in the ternary image have been elaborated to determine the concentrations of radiometric elements and the variation of radiometric character along the exposed terrains. The F parameter was calculated to target high potassium concentration areas associated with hydrothermal alteration zones. Combining the two methods highlighted four hydrothermal alteration zones considered very promising from a mining point of view. These zones are generally linked to the magma bodies affected by normal faults and exhibit a clear spatial correlation with mineral occurrences. [ABSTRACT FROM AUTHOR]

Established 2D seismic data processing methods such as Kirchhoff pre‐stack time migration and Kirchhoff pre‐stack depth migration function relatively well for regular acquisition geometries and well‐constrained velocity models. Recently developed focusing pre‐stack depth migration methods have the potential to enhance image quality in the case of sparse and non‐regular source–receiver distribution. We have tested the performance of the coherency migration method as one of these focusing migration approaches in comparison to standard dip‐moveout and Kirchhoff pre‐stack time migration techniques by applying them to the Swayze East seismic profile acquired in the Abitibi greenstone belt of Canada. This seismic profile represents a crooked‐line survey that intersects several metal‐bearing deformation zones, providing good target geometries to examine various pre‐stack migration methods. Analysis of the seismic data indicates reflectivity associated with shallowly dipping reflections appears relatively well preserved over the entire 0–6 km offset range for the frequency range between 20 to 90 Hz. Although most reflections are visible already in either the dip‐moveout or the Kirchhoff pre‐stack time migration results, the coherency migration method delivers the most improved image showing all reflective structures inferred for this area. The comparisons suggest the coherency migration method can be considered as superior in terms of resulting seismic image quality compared with conventional approaches for this type of crooked‐line seismic survey in such a complex geological setting. [ABSTRACT FROM AUTHOR]

The mapping of the vertical and lateral variations in the physical properties of the few‐meter cover layer over near‐surface aquifers is important for hydrogeological modelling, particularly for the quantification of the recharge of groundwater systems. The first ground‐based time‐domain electromagnetic survey over a small catchment (Avesnelles, France) of the watershed of Orgeval (Seine basin) was carried out to determine discontinuities in the first silt layer as well as in the Brie multilevel aquifer limestone horizon. The results highlighted the following: (1) a good sensitivity of the time‐domain electromagnetic survey to the presence of multi‐decametric resistive sand lenses, particularly in a location where they were previously identified and (2) the interest in conducting a survey at a fine sampling step but extending to the meso‐scale. To overcome the sampling issue over a watershed of several hundred square kilometres, we proposed numerically assessing the use of a prototype of low‐cost airborne transient electromagnetic systems towed by light fixed‐wing airplanes (with transmitting and receiving loops in the same plane). The present numerical analysis, in 1D for the vertical (i.e. thickness) variation and in 3D for the lateral extensions of localized sandy and resistive units, showed that a conductive few‐meter cover can be mapped even with a system flying at 50 m with, however, the need of a priori constraint on the resistivity of the first layer to estimate its thickness variation as accurately as possible. Even if it did not bring more sensitivity to the layer thickness and despite the severe difficulty of practical implementation with a decametric emission loop, the vertical co‐planar configuration potentially offered better near‐surface lateral resolution (down to ∼40 m) to delineate the sandy units (discontinuities) within the silt layer (if units are at least 50 m in size) and provided better spatial constraints compared to the classical horizontal co‐planar geometry used in the time‐domain electromagnetic. Even if not aerodynamically in the plane of the emission loop, the measurement of the Hx component with a vertical dipole emission loop (PERPxz geometry for perpendicular) improved the lateral resolution (down to ∼20 m; still with at least 50 m size sand units) and confirmed that a geometry different from the classical horizontal co‐planar configuration could be valuable. [ABSTRACT FROM AUTHOR]

The propagation of microseismicity in subsurface media is complex. We developed an anisotropic petrophysical model based on an empirical formula, linear slip theory and the bond transform method considering real underground conditions. Using Biot's equations, the seismic response to a general dislocation source in fracture‐induced anisotropic two‐phased media was solved using a staggered grid high‐order finite‐difference algorithm. To understand the relationship between the microseismic wave and fracture parameters, we then designed several different models to calculate the wavefield snapshots and analyse the effect of the fracture volume ratio and orientation. The modelling results indicate that the shear faulting source generates three types of waves in two‐phase media. Fractures can render homogeneous media anisotropic, and anisotropy becomes more noticeable with an increase in the fracture volume ratio. This decreases the velocity of the fast longitudinal and transverse waves in the vertical direction and increases the velocity of the slow longitudinal wave in a certain range. The fracture orientation mainly influences the moment tensor and then affects the wavefronts. These simulations lay the foundation for further studies on microseismic wave propagation in fracture‐induced anisotropic media. [ABSTRACT FROM AUTHOR]

Producing an accurate and valid mineral prospectivity map is one of the most significant parts of mineral exploration studies. For this purpose, it is needed to obtain valid evidential layers and integrate them with an accurate methodology. Knowledge and data‐driven methods are two primary techniques applied to combine various evidential layers for mineral prospectivity mapping, of which each of them includes a variety of analytical techniques. In this study, in the first step, satellite data, aeromagnetic and airborne radiometric data, stream sediment geochemical data and geological data were applied to create valid remote sensing, geophysical, geochemical, lineaments and lithological evidential layers of the study area that are an essential factor in recognition porphyry copper mineralization, then in the second step, based on the known mineralization occurrences data, the evidential layers were weighted. Finally, these layers were integrated using fuzzy logic and index overlay methods in a combination of knowledge and data‐driven way. Validation of each layer was done using available data in the second step. The final mineral prospectivity map was evaluated, and the confirmation of this layer detected that the final mineral prospectivity map obtained from data‐driven multi‐index overlay method has a higher ore prediction rate of 76%, which identifies 24% of the area as potential zones for further exploration. [ABSTRACT FROM AUTHOR]

The Central‐Eastern Mediterranean region is known to be a complex area due to the interaction of four tectonic plates, namely Arabia, Africa, Anatolia and Eurasia, and by the presence of an ancient oceanic crust in the Herodotus and Ionian Basins. The analysis of the available literature highlights that the distribution of the freely available geophysical data (i.e. seismic, gravity and magnetic observations) is quite disparate. In this framework, high‐resolution global gravity field models, such as XGM2019e, mainly based (offshore) on satellite data, can be profitably used as a uniform dataset to study, in a coherent way, large regions. In the current work, we exploit the XGM2019e model, together with a set of a priori information, derived mainly from geophysical data retrieved from the literature, to study the structure of the crust in the Central‐Eastern Mediterranean area. The study is organized in three different phases: in the first one, we enhanced the map of geological crustal provinces by means of an automatic Bayesian classification algorithm applied to the second radial derivatives of the gravitational potential. In the second phase, using as observation a grid of gravity anomalies, we applied a full three‐dimensional inversion procedure (always based on a Bayesian paradigm) to estimate the mass density variations and the geometries of the main geological units in the whole study area. Finally, in the third phase, we performed a refined three‐dimensional local inversion on the Cyprus area to improve the modelling of the shallowest layers. The main results of this study, carried out in the framework of the European Space Agency GIADA project, are freely available, upon request, at https://www.g‐red.eu/geophysics/. [ABSTRACT FROM AUTHOR]