Search

In the present study, the impact behavior of gravity casting AlSi10Mg alloy was evaluated with an instrumented Charpy pendulum. The effect of hot isostatic pressing, also followed by a T6 treatment, was analyzed in comparison with samples in the as-cast, annealed and T6 conditions. Furthermore, the effect of the innovative high-pressure T6 was investigated. It was found that the hot isostatic pressing is able to ensure densification of the alloy with an increase in both hardness and energy absorbed during impact. The T6 treatment performed at atmospheric pressure after the hot isostatic pressing is able to increase hardness and peak force. At the same time, the innovative high-pressure T6 is able to ensure similar results than those of hot isostatic pressing followed by T6, leading to a significant decrease in the treatment duration and costs and reducing the carbon footprint of the manufacturing process.

Dissimilar friction stir welding joints are widely employed in the industrial field due to the excellent microstructural and mechanical properties of the resulting joints. Nevertheless, to further enhance the weld properties, the addition of reinforcement particles on the joint-line during the process has been proven effective for increasing its mechanical performance. In the present investigation, the microstructure and the impact behaviour of FSWed joints between AA2024-T351 and AA7075-T651 aluminium plates were investigated, considering the effect of different process parameters selected through a full factorial 2k design of experiments: both the rotational and translational speed of the tool, as well as the addition of Al2O3-SiC microparticles, were considered as input parameters. Unnotched 10 x 5 x 55 mm impact specimens were tested through an instrumented 50 J Charpy pendulum: total impact energy, the two complementary initiation and propagation energies as well as the peak force were correlated to the adopted process parameters. From the performed analyses, it was found that joints with reinforcing particles are prone to form wormhole defects across the stir zone that not only affect the microstructural development, but also the impact behaviour since they require less energy at break in comparison with joints fabricated without particles addition.

In the present study the impact behavior of gravity casting AlSi10Mg alloy was evaluated with an instrumented Charpy pendulum. The effect of hot isostatic pressing, also followed by a T6 treatment, was analyzed in comparison with samples in the as-cast, annealed and T6 conditions. Furthermore, the effect of the innovative high-pressure T6 was investigated. It was found that the hot isostatic pressing is able to ensure densification of the alloy with an increase in both hardness and energy absorbed during impact. The T6 treatment performed at atmospheric pressure after the hot isostatic pressing is able to increase hardness and peak force. At the same time, the innovative high-pressure T6 is able to ensure similar results than those of hot isostatic pressing followed by T6, leading to a significant decrease in the treatment duration and costs and reducing the carbon footprint of the manufacturing process.

This paper discusses the effect of different surface treatments on shape memory alloy wires embedded in PolyEster (PE) and VinylEster (VE) polymeric matrices. In particular, two types of chemical etching and a chemical bonding with a silane coupling agent have been performed on the surfaces of the wires. Pull-out tests have been carried out on samples made from a specifically designed Teflon mould. Considering the best results of the pull-out tests obtained with PE resin, the debonding induced by strain recovery of 4%, 5% and 6% pre-strained NiTi wires has been evaluated with the wires being subjected to different surface treatment conditions and then being embedded in the PE matrix. The results prove that the wires functionalised and embedded in the PE resin show the maximum pull-out forces and the highest interfacial adhesion. Finally, it has been found that debonding induced by strain recovery is strongly related to the propagation towards the radial direction of sharp cracks at the debonding region.

In the present paper, microstructural and mechanical properties of an innovative AlSi3Mg alloy were studied. Particularly, the effect of the addition of Cr and Mn on tensile strength and impact toughness was evaluated. In fact, the presence of these elements leads to the formation of an intermetallic phase with a globular or polyhedral morphology. It was therefore investigated the role played by Cr-Mn containing particles in the failure mechanism and the influence of the heat treatment parameters. Moreover, tensile and impact tests were performed on A356 samples in T6 condition, whose results were compared with the performance of the innovative alloy. Considering the static properties, the innovative alloy showed remarkable values of tensile strength, while ductility was improved only after heat treatment optimization. Poor impact toughness values were measured and the microstructural analysis confirmed the presence of coarse intermetallics, acting as crack initiation and propagation particles, on the fracture surfaces.

In this paper, the hot tearing behaviour in Al-(4.86)%Cu sand mould castings was preliminary investigated by means of microstructural examination and image analysis. A dog-bone pattern was employed for the realisation of the castings and three Al-Cu alloys with different Cu and Si contents were used. The effects of the alloy composition and of different pouring temperatures on the hot tearing behaviour of the castings were evaluated. The quantity of the eutectic phase available during solidification is considered a very important parameter for the crack healing phenomenon, in fact the eutectic liquid flows into the hot tear areas and covers parts of the cracks. The hot tear paths and surfaces were observed by means of optical and scanning electron microscopes, which showed that the fracture surfaces were dominated by bridged grain boundaries and the presence of a liquid film, in particular at higher copper concentrations. Several samples were also drawn from the zones characterised by the maximum cross-section variation and the micrographs from the optical microscope were statistically analysed by means of commercially available image analysis software. The quantitative microstructural parameters of percentage, mean area and distribution of the eutectic phase were evaluated and correlated to the capacity of the eutectic liquid to heal open fractures caused by hot tearing for the examined alloys.

This paper discusses the effect of different surface treatments on shape memory alloy wires embedded in PolyEster (PE) and VinylEster (VE) polymeric matrices. In particular, two types of chemical etching and a chemical bonding with a silane coupling agent have been performed on the surfaces of the wires. Pull-out tests have been carried out on samples made from a specifically designed Teflon mould. Considering the best results of the pull-out tests obtained with PE resin, the debonding induced by strain recovery of 4%, 5% and 6% pre-strained NiTi wires has been evaluated with the wires being subjected to different surface treatment conditions and then being embedded in the PE matrix. The results prove that the wires functionalised and embedded in the PE resin show the maximum pull-out forces and the highest interfacial adhesion. Finally, it has been found that debonding induced by strain recovery is strongly related to the propagation towards the radial direction of sharp cracks at the debonding region.