Search

The existing ECRH system at W7-X consists of 10 gyrotrons, with output power levels ranging from 0.6 MW up to 1.0 MW each at a frequency of 140 GHz, quasi-optical transmission lines and microwave launchers at the plasma vessel. Compared to other large fusion experiments, W7-X has a relatively low power-to-volume ratio. However high heating power is particularly necessary for achieving high plasma beta values, where the improved confinement of fast ions, one of the optimization criteria of W7-X, can be examined. It is therefore necessary to expand the ECRH systems in several consecutive steps. It is planned to increase the number of gyrotron positions from 10 to 12 and at the same time to evolve the gyrotron output power in several development steps from 1 MW to nominal 1.5 MW and, finally, up to 2 MW. At the same time, the transmission lines will also be upgraded for 2 MW operation. A special effort is also made to improve the reliability of the system by the fast control system.

This paper gives an overview about three key measurement capabilities at KIT/IHM for fusion gyrotrons. The discussed topics are: RF window test facility, low power launcher test setup and the frequency measurement setup placed at the high power test facility. Further, approaches for upgrading the setups to frequencies above 200 GHz are discussed.

ECRH&CD is one of the favorite heating system for magnetically confined nuclear fusion plasmas. KIT is strongly involved in the development of high power gyrotrons for use in ECRH systems for nuclear fusion. KIT is upgrading the sub-components of the existing 2 MW, 170 GHz coaxial-cavity short-pulse gyrotron to support long-pulse operation up to 1 s, all components will be equipped with a specific active cooling system. Two important developments for future high power, highly efficient gyrotrons will be discussed: design of gyrotrons with high operating frequency (∼ 240 GHz) and efficiency enhancement by using advanced collector designs with multi-staged voltage depression.

The European 1 MW, 170 GHz CW industrial prototype gyrotron for ECRH&CD on ITER was under test at the KIT test facility during 2016. In order to optimize the gyrotron operation, the tube was thoroughly tested in the short-pulse regime, with pulse lengths below 10 ms, for a wide range of operational parameters. The operation was extended to longer pulses with a duration of up to 180 s. In this work we present in detail the achievements and the challenges that were faced during the long-pulse experimental campaign.

The electron cyclotron (EC) system of ITER for the initial configuration is designed to provide 20MW of RF power into the plasma during 3600s and a duty cycle of up to 25% for heating and (co and counter) non-inductive current drive, also used to control the MHD plasma instabilities. The EC system is being procured by 5 domestic agencies plus the ITER Organization (IO). F4E has the largest fraction of the EC procurements, which includes 8 high voltage power supplies (HVPS), 6 gyrotrons, the ex-vessel waveguides (includes isolation valves and diamond windows) for all launchers, 4 upper launchers and the main control system. F4E is working with IO to improve the overall design of the EC system by integrating consolidated technological advances, simplifying the interfaces, and doing global engineering analysis and assessments of EC heating and current drive physics and technology capabilities. Examples are the optimization of the HVPS and gyrotron requirements and performance relative to power modulation for MHD control, common qualification programs for diamond window procurements, assessment of the EC grounding system, and the optimization of the launcher steering angles for improved EC access. Here we provide an update on the status of Europe’s contribution to the ITER EC system, and a summary of the global activities underway by F4E in collaboration with IO for the optimization of the subsystems.

The European Gyrotron Consortium (EGYC) is responsible for developing one set of 170 GHz mm-wave sources, in support of Europe’s contribution to ITER. The original plan of targeting a 2 MW coaxial gyrotron is currently under discussion, in view of essential delays and damages. This paper reports on the latest results and plans with regard to the two 2 MW gyrotron prototypes, the industrial prototype at CRPP’s CW test stand and a modular pre-prototype at KIT. The industrial prototype was delivered to CRPP end of September 2011 and reached an output power of 2 MW at an efficiency of 45 % and with good RF beam pattern, in only four days of short pulse RF test. These results validated all design changes made in reaction to the results of the experiments in 2008. On the fifth experimental day, an internal absorber broke, terminating any further experiment with this tube. In parallel, design and experimental activities at KIT went on, in particular featuring reduced stray radiation down to 4% of the RF power. Next years’ plans for the 2 MW modular pre-prototype foresee a stepwise increase of pulse length.