Search

In this study, the possibility of culturing Dunaliella salina in stickwater (SW) as the main effluent of fishmeal plants was evaluated. D. salina was grown in different media obtained by replacing standard Guillard medium (F/2) with SW at 0% (control), 10%, 25%, 50%, 75%, and 100% ratios. The cell density, pigment contents, proximate composition, saponification value, and fatty acids (FAs) profiles were measured for 14 days. SW was collected from a kilka fishmeal factory in northern Iran, and the characteristics indicated high concentrations of nitrate (242.00 mg L -1 ) and phosphate (11.13 mg L -1 ). A significant increase in the cell density was observed in 14 days when 75% SW was used. Moreover, SW significantly affected the pigment contents. The highest contents of chlorophylls, total carotenoids, and β-carotene (3.64 μg mL -1 ) were calculated in 75% SW. According to the algal proximate composition, the highest and lowest contents of lipid were accumulated in 75% and 100% SW, respectively (p < 0.05). The highest level of saturated FAs was observed in 75% SW compared with the others (p < 0.05). In conclusion, replacing F/2 with SW indicated the capability of D. salina to grow in a treated medium with 75% SW substitution as a bioremediator.

Wastewater rich in organic carbon, nitrogen and phosphorus may serve as a convenient source of carbon and nutrients for a year-long microalgae production. Scientific reports indicate that some single-cell microalgae such as Chlorella and Scenedesmus, are highly tolerant to wastewater environments and efficiently remove biogenic compounds. The aim of this study was to determine the possibility of using the effluent produced in the process of anaerobic degradation of whey as a culture medium for the multiplication of Chlorella vulgaris algae biomass and to characterise their growth efficiency and rate. The content of nitrogen and phosphorus in wastewater was sufficient for conducting an effective culture of algae. The efficiency of nitrogen removal in the flow system was 15.61 ± 1.38 mg N/dm 3 /day.

In this study, the growth and high-valued products accumulation characteristics of three common high-valued microalgae (Chlorella sp. HQ, Scenedesmus sp. LX1, and Chlorella vulgaris) in saline-alkali leachate were compared to select the species with greatest utilization potential. The results showed that after 28 days of cultivation, among three microalgae, Chlorella sp. HQ grew best with its maximum density at peak of 1.16 × 10 7 cells mL -1 and lipid production per unit cell (0.047 ± 0.006 × 10 -7 mg cell -1 ) and lipid content (18.18 ± 3.14%) were largest. The triacylglycerol (TAG) yield and content of Scenedesmus sp. LX1 were the highest, reaching 0.005 ± 0.000 × 10 -7 mg cell -1 and 19.74 ± 2.53%, respectively, which was slightly higher than those of Chlorella sp. HQ. According to comprehensive comparison, Chlorella sp. HQ was most suitable to grow in the saline-alkali leachate in terms of algal density, lipid yield, and content. The potential comparison and effects of salinity on the high-valued products accumulation of Chlorella sp. HQ compared with those in SE standard medium, reclaimed water, and tap water were further carried out. It was found that the density order of Chlorella was saline-alkali leachate > SE medium > reclaimed water > tap water. And the Chlorella density in the leachate with a salinity of 0.14% was greater than the other three salinities (0.32%, 0.45%, and 0.6%) at the end of cultivation. While the maximum lipid yield per unit cell and lipid content of Chlorella occurred in the salinity of 0.6%, which indicated that high salinity promoted the accumulation of lipid. Furthermore, other high-valued products (including starch, protein, total sugar, and photosynthetic pigments) accumulation characteristics were analyzed and found that they were all superior than those in SE medium. And with the salinity decreased, the microalgal protein and starch contents decreased. The contents of photosynthetic pigment and total sugar reached a maximum at salinities of 0.32% and 0.45%, respectively.

The approach of combining the microalgae cultivation with wastewater provides a cost-effective and eco-friendly perspective in the production of microalgae-based bio-products. In the present investigation, microalgae Scenedesmus rubescens KACC 2 isolated from catchment region of River Noyyal was found to be efficient in removing nitrogen, phosphorus, and heavy metals from industrial and domestic effluents, which was optimized through central composite design matrix for higher biomass generation. Nutrient requirements for the growth were optimized and evaluated using Plackett-Burman design to check the effect of variables. Three variables, viz., nitrate, phosphate, and inoculums, were found to be significant among the 11 variables tested, and the interaction between these variables and its optimum concentrations were statistically studied using central composite design matrix. The optimized growth conditions of this strain were found to be as nitrate (0.2%), phosphate (0.018%), and inoculums (7.5%). These conditions yielded a higher biomass of 0.73 g/L from the optimized media which was 5.4 times higher than the regular growth media. FT-IR analysis showed the variations in the spectra and also in biomolecular composition with 2-fold increase in the lipid and protein region when grown in optimized culture conditions. Lipid profile showed the presence of saturated and monounsaturated fatty acids in the biomass accepting it as a source of energy feedstock. This study concludes that nitrate, phosphate, and inoculums play a significant role in biomass production of S. rubescens with phycoremediation potential that can be exploited for simultaneous wastewater treatment-coupled biomass production.

Treatment of wastewater by using of microalgae is a cost-effective system. Chlorella sorokiniana pa.91 and Chlorella vulgaris were studied in this research. Chlorella sorokiniana pa.91 was isolated from the dairy wastewater. In this study, treated wastewaters in preliminary and secondary treatment units of dairy wastewater treatment plant were used as medium. Maximum growth of two species of microalgae was examined in these two mediums, and also, nutrient removal was studied. The performance of two species of microalgae was studied on laboratory scale at different temperatures and light intensities. The best observed temperatures for Chlorella vulgaris and Chlorella sorokiniana pa.91 were 25 and 28 °C, respectively, and the best observed performance for them was obtained at 7500 lx. The values of specific growth rate and biomass productivity in effluent of preliminary treatment unit for Chlorella vulgaris were 0.331 day -1 and 0.214 g L -l  day -1 , respectively, and for Chlorella sorokiniana pa.91 were 0.375 day -1 and 0.233 g L -l  day -1 , respectively. Also, these parameters for Chlorella vulgaris in effluent of secondary treatment unit were determined 0.359 day -1 and 0.166 g L -l  day -1 , respectively, and for Chlorella sorokiniana pa.91 were obtained 0.422 day -1 and 0.185 g L -l  day -1 , respectively. The removal efficiency of nitrate, ammonia, phosphate, and chemical oxygen demand for Chlorella sorokiniana pa.91 and Chlorella vulgaris in both of effluents was more than 80%. Based on the results, effluent of treatment plants can be a suitable microalgae growth medium, and the microalgae can be used as effective post treatment system.

Commercial usage of ZnO nanoparticles has increased recently due to its versatile applications, raising serious environmental concern because of its ultimate release of nanoparticles in aquatic ecosystem. Therefore, it is important to understand the impact of ZnO nanoparticle toxicity especially on algal flora, which is the primary producer in the aquatic food chain. In the current study, algal growth kinetics was assessed after the exposure of zinc oxide nanoparticles and its bulk counterpart to Coelastrella terrestris (Chlorophyceae). Zinc oxide nanoparticles were found to be more toxic (y = 34.673x, R 2  = - 0.101, 1 mg L -1 nanoparticle (NP)) than bulk (y = 50.635x, R 2  = 0.173, 1 mg L -1 bulk) by entrapping the algal cell surface. Higher toxicity may be due to oxidative stress within the algal cell as confirmed through biochemical analysis. Biochemical parameters revealed stressful physiological condition in the alga under nanoparticle exposure, as lactate dehydrogenase release (18.89 ± 0.2 NP; 13.67 ± 0.2 bulk), lipid peroxidation (0.9147 ± 1.2 NP; 0.7480 ± 0.8 bulk), and catalase activity (4.77 ± 0.1 NP; 3.32 ± 0.1 bulk) were found higher at 1 mg L -1 in the case of nano-form. Surface adsorptions of nanoparticles were observed by SEM. Cell organelle damage, cell wall breakage, and cytoplasm shrinkage were found as responses under toxic condition through SEM and TEM. Toxicity was found to be influenced by dose concentration and exposure period. This study indicates that nano-form of ZnO is found to be more toxic than bulk form to freshwater alga.

This study investigated the growth-dependent role of algal organic matters (AOMs) to achieve high removal efficiency (R.E) of microalgae. The results showed that the microalgae cells produced 96 ± 2% of total AOMs as loose bound AOMSS (LB-AOMs) and 4 ± 1% as cell-bound (CB-AOMs) in exponential phase. In stationary phase, LB-AOMs and CB-AOMs were 46 ± 0.7percentage and 54 ± 0.2 percentage, respectively. The R.Es in exponential and stationary phase were 83 ± 2.6% and 66 ± 1.2%, respectively. It is found that the difference of biomass concentration (between exponential and stationary phase) had no significant impact on the R.E (P > 0.01). Further investigations revealed that LB-AOMs inhibit flocculation in exponential and CB-AOMs in stationary phase; however, CB-AOMs showed stronger inhibition than the LB-AOMs (P < 0.01). The provision of calcium (17 ± 0.9 mg/L) to the culture reduced the AOMs inhibition and improved the R.E from 66 ± 1.2% (in control) to 90 ± 4.2%. An increase in R.E was attributed to the interaction of calcium with AOMs and subsequently acting as a flocculant. The findings of this study can be valuable to improve the performance of auto-flocculation technology, which is mainly limited by the presence of AOMs. Graphical Abstract.

This study compared the efficiency of nutrient removal and lipid accumulation by a monoculture of Scenedesmus obliquus and mixed cultures of microalgae. The highest removal efficiencies of ammonium (99.2%), phosphate (91.2%), and total organic carbon (83.6%) occurred in the monoculture. All the mixed cultures were dominated by S. quadricauda; in some mixed cultures, the proportions of Chlamydomonas reinhardtii and C. microsphaera reached > 20%. The lipid content and lipid production in the monoculture were 15.9% and 52.3 mg kg -1 , respectively, significantly higher than those in all the mixed cultures of microalgae. In all the mixed cultures, the proportion of palmitic acid was > 50%. The results suggest that the monoculture had advantages over the mixed culture of microalgae in terms of nutrient removal and lipid production.

Oleaginous microalgae and yeast are the two major propitious factories which are sustainable sources for biodiesel production, as they can accumulate high quantities of lipids inside their bodies. To date, various microalgal and yeast species have been exploited singly for biodiesel production. However, despite the ongoing efforts, their low lipid productivity and the high cost of cultivation are still the major bottlenecks hindering their large-scale deployment. Co-culturing of microalgae and yeast has the potential to increase the overall lipid productivity by minimizing its production cost as both these organisms can utilize each other's by-products. Microalgae act as an O 2 generator for yeast while consuming the CO 2 and organic acids released by the yeast cells. Further, yeast can break complex sugars in the medium, which can then be utilized by microalgae thereby opening new options for copious and low-cost feedstocks such as agricultural residues. The current review provides a historical and technical overview of the existing studies on co-culturing of yeast and microalgae and elucidates the crucial factors that affect the symbiotic relationship between these two organisms. Furthermore, the review also highlighted the advantages and the future perspectives for paving a path towards a sustainable biodiesel product.

The present work investigated the potential of the green alga Chlorella vulgaris to produce high-quality biofuel under culture stress conditions. The cultivation was carried out in a 1000 l open plate tank system, which provides biomass yields comparable to open pond systems, but with less area needed. Algal biomass and lipid content were measured repeatedly. We compared the two solvent systems n-hexane and hexane/isopropanol (HIP) for extraction efficiency of lipids and applied three different extraction methods Soxhlet, soaking, and soaking followed by Soxhlet (soak-Sox). The combination of the HIP solvent and the soak-Sox provided the highest lipid yield (15.8 ± 0.174). Volumetric biomass and lipid productivity were 0.201 g l -1  day -1 and 31.71 mg l -1  day -1 , respectively, whereas areal biomass and lipid productivity were 25.73 g m -2  day -1 and 4.066 g m -2  day -1 , respectively. The fatty acid profile by means of gas chromatography resulted in seven fatty acids from C 12 to C 18 . The most abundant fatty acid methyl esters (FAMES) were palmitic (C16:0), oleic (C18:1), and stearic (C18:0) acids. Lipid synthesis enhanced by optimizing the Kuhl growth medium with replacing nitrate by urea (50% N compared to the original recipe) increased salt content (10 g/l NaCl), ferrous sulfate (0.5 g/l), and sodium acetate addition (1 g/l). With regard to density, kinematic viscosity, gravity, pour point, flash point, and cetane number, the Chlorella-biodiesel comply with ASTM and EN standards thus pointing at the high potential of lipids synthesized by Chlorella as a feedstock for biodiesel production.

The present study reports the use of Citrus limetta (CL) residue for cultivating Chlorella sp. mixotrophically to augment production of biodiesel. The cultivation of Chlorella sp. using CL as media was carried out by employing a fed-batch technique in open tray (open tray+CL) and in software (BioXpert V2)-attached automated photobioreactor (PBR+CL) systems. Data showed the limit of nitrogen substituent and satisfactory organic source of carbon (OSC) in CL, causing > 2-fold higher lipid content in cells, cultivated in both the systems than in control. For the cells grown in both the systems, ≥ 3-fold enhancement in lipid productivity was observed than in control. The total fatty acid methyl ester (FAME) concentrations from lipids extracted from cells grew in PBR+CL and in open tray+CL techniques were calculated as 50.59% and 38.31%, respectively. The PBR+CL system showed improved outcomes for lipid content, lipid and biomass productivity, FAME characteristics and physical property parameters of biodiesel than those obtained from the open tray+CL system. The physical property parameters of biodiesel produced from algal cells grown in PBR+CL were comparable to existing fuel standards. The results have shown lower cold filter plugging point (- 6.57 °C), higher cetane number (58.04) and average oxidative stability (3.60 h). Collectively, this investigation unveils the novel deployment of CL as a cost-effective feedstock for commercialisation of biodiesel production.

CO 2 , SO 2 , and NO are the main components of flue gas and can cause serious environmental issues. Utilization of these compounds in oleaginous microalgae cultivation not only could reduce air pollution but could also produce feedstock for biodiesel production. However, the continuous input of SO 2 and NO inhibits microalgal growth. In this study, the toxicity of simulated flue gas (15% CO 2 , 0.03% SO 2 , and 0.03% NO, balanced with N 2 ) was reduced through automatic pH feedback control. Integrated lipid production and CO 2 fixation with the removal of SO 2 and NO was achieved. Using this technique, a lipid content of 38.0% DW was achieved in Chlorella pyrenoidosa XQ-20044. The lipid composition and fatty acid profile indicated that lipid production by C. pyrenoidosa XQ-20044 cultured with flue gas is suitable as a biodiesel feedstock; 81.2% of the total lipids were neutral lipids and 99.5% of the total fatty acids were C16 and C18. The ratio of saturated fatty acids to monounsaturated fatty acids in the microalgal lipid content was 74.5%. In addition, CO 2 , SO 2 , and NO from the simulated flue gas were fixed and converted to biomass and lipids with a removal efficiency of 95.9%, 100%, and 84.2%, respectively. Furthermore, the utilization efficiencies of CO 2 , SO 2 , and NO were equal to or very close to their removal efficiencies. These results provide a novel strategy for combining biodiesel production with biofixation of flue gas.

In this study, the influences of organic carbon sources (OCS, including xylose, glucose, maltose, sucrose, and starch) and inorganic and organic nitrogen sources (INS, including ammonia chloride and sodium nitrate; ONS, including arginine, alanine, proline, and valine) and metal ions (including Na + , K + , Mn 2+ , Zn 2+ and Cu 2+ ) on the growth, lipid accumulation, and nitrogen and phosphorus (N&P) removal capabilities of oleaginous Scenedesmus sp. LX1 under heterotrophic conditions were investigated. The results showed that glucose was the only OCS for Scenedesmus sp. LX1 to grow well with specific growth rate of 0.935 days -1 , maximum biomass of 1.72 g L -1 , and largest removal rates of N&P and organic carbon reaching 72.228%, 93.034%, and 19.208%, respectively. After 11 days of cultivation, the maximal biomass reached in the group with starch or glucose while maximal lipid and triacylglycerol (TAG) yields reached in the groups with maltose and sucrose, respectively. Sodium nitrate was best nitrogen source as the largest algal density, maximal yields of lipids and TAGs, and highest N&P removal rates reached up to 1.105 × 10 7 cells·mL -1 , 196.70 mg L -1 , 5.19 mg L -1 , 89.61% and 100%, respectively. Scenedesmus sp. LX1 was found to have great tolerance to Na + , K + , Mn 2+ , and Zn 2+ while 0.5 mg L -1 Cu 2+ had a strong inhibition on growth and N&P removal rate of Scenedesmus sp. LX1. Concentration increasing of five metal ions all caused the yield increases of microalgal lipid and TAGs. Graphical abstract.

Algae are being grown for wastewater purification and biofuels production. Their growth on a substrate facilitates these uses by allowing facile separation of algae from the water. Here, we compare different materials to determine which would best serve this purpose. A mixed culture of Anabaena and Chlorella was grown on various synthetic and natural fiber fabric substrates in a trough system with recirculating simulated wastewater. Filter materials studied as substrates for algal growth were muslin, olefin, pellon (acrylic), two types of polyester, and two types of nylon. Biomass accumulation on the various filter substrates was recorded at 7, 14, and 28 days. Filters were weighed before and after the growth periods and changes in dry biomass were recorded. Biomass accumulation was significantly affected by the fabric type. Olefin fostered the greatest increase in biomass while nylon and polyester also supported competitive increases in biomass. Pellon showed the smallest biomass increase and muslin decreased in mass due to material disintegration. Other concerns such as abrasion resistance and UV susceptibility are discussed.

Microalgal biomass produced from the phycoremediation of wastewater represents an important protein source, lipids, and natural antioxidants and bioproducts. Therefore, the microalgal biomass and their derived compounds are used in animal and aquaculture feed as well as human nutrition and health products. Many microalgal species have shown promising potential for many bioproducts. However, significant processes to find the optimum quality and quantity of microalgal biomass are still required especially when it is used as a replacement for aquaculture feed. The limitations lie in the selection of microalgal species and their production. The present review discusses the potential generation of bioproducts from microalgal biomass resulting from the phycoremediation of wet market wastewater. The consortium approach in wastewater treatment and the comparison between biomass production and available common feeds for aquaculture were reviewed.

In this study, effects of different abiotic factors were studied on biomass and lipid yield of green microalga Chlorella minutissima (C. minutissima) Various concentrations of abiotic factors like nitrogen, phosphorus, glucose, iron, zinc, different values of pH, temperature, light intensity and different photoperiods were observed on the biomass growth and lipid yield of C. minutissima cultivated with modified CHU-13 medium. Initially, three cultivation media namely, Bold's basal medium (BBM), modified CHU-13 and blue-green-11 (BG-11) were used to culture C. minutissima in batch mode. Microalga cultivated with modified CHU-13 medium resulted in maximum biomass and lipid yield of 970 ± 0.21 and 356.63 ± 0.51 mg/L, respectively. To maximize biomass and lipid yield of microalga further, it was cultivated with modified CHU-13 medium and variation of above mentioned abiotic factors was done. Different biomass and lipid yields were achieved for different abiotic factors varied. Highest biomass of 1840.49 ± 0.62 mg/L was achieved with 12 g of glucose containing medium and highest lipid yield of 579.86 ± 0.76 mg/L was achieved with 0.3 g of nitrogen containing medium. GC-MS analysis of biodiesel obtained from C. minutissima biomass cultivated with modified CHU-13 medium shown the presence of C14:0, C16:0, C16:1, C18:0, C18:1, C18:2, C18:3, C20:0, C20:1 and C22:0. Properties of biodiesel obtained from C. minutissima were found in compliance with ASTM-6751-02 and European biodiesel standards EN14214. These results suggest that C. minutissima can be used as a potential biodiesel feedstock for microalgal biodiesel production.

Trash fish feeding of cage fish can result in marine pollution. Whole and chopped trash fish can leach pollutants such as ammonia, phosphate and protein into surrounding waters. Reduction of pollution can be achieved by recycling the wastewater generated from trash fish feeding for cultivation of microalgae. Microalgae are potent candidates for the production of renewable and sustainable products such as feed and food, health and pharmaceutical, cosmeceutical, industrial products, and biofuel. Two microalgae, Chlorella saccharophila and Nannochloropsis sp., have the potential to produce high amounts of polyunsaturated fatty acids. Furthermore, high oil content ranging from 10.7 to 13.6% is found in Chlorella saccharophila and up to 9.3% for Nannochloropsis sp. Moreover, these microalgae can also be utilized as a biofuel to give a mean calorific value of 5364 Cal/g which is higher than that of wood for Chlorella saccharophila and 6132 Cal/g which is equivalent to that of coal for Nannochloropsis sp. An alternative biofuel derived from microalgae is feasible due to the fact that they do not compete for arable land for cultivation and land crops for feed and food. This study discusses the synergistic coupling of microalgae mass production with wastewater treatment and carbon sequestration potential for mitigation of environmental impacts and a technically viable alternative energy resource. Additionally, the de-oiled biomass byproduct after oil extraction or its whole biomass can be converted into sustainable and renewal industrial products such as bioplastic, biopaint, bioasphalt, and biobuilding components.

Microalgae are promising sustainable and renewable sources of oils that can be used for biodiesel production. In addition, they contain important compounds, such as proteins and pigments, which have large applications in the food and pharmaceutical industries. Combining the production of these valuable products with wastewater treatment renders the cultivation of microalgae very attractive and economically feasible. This review paper presents and discusses the current applications of microalgae cultivation for wastewater treatment, particularly for the removal of phenolic compounds. The effects of cultivation conditions on the rate of contaminants removal and biomass productivity, as well as the chemical composition of microalgae cells are also discussed.

A stochastic ecological model with an integrated equilibrium temperature model was developed to predict microalgae growth and phosphorus removal in cold region waste stabilization ponds (WSPs). The model utilized a Monte Carlo simulation to account for parameter uncertainty. The equilibrium temperature model was parameterized using field data collected from two WSPs in Nunavut, Canada, from 2012 to 2014. The equilibrium temperature model provided good agreement with field data on a daily time step. The full model was run using historic (1956-2005) temperature and solar radiation data from five communities (Baker Lake, Cambridge Bay, Coral Harbour, Hall Beach, Resolute) in Nunavut, Canada. The communities represented a range of geographical locations and environmental conditions. Logistic regression on pooled model outputs showed that mean July temperature and mean treatment season temperature (June 1-September 15, ice-free period) provided the best predictors for microalgae growth. They had a predictive success rate of 93 and 88%, respectively. The modelled threshold (50% probability from the Monte Carlo simulation) for microalgae growth was 8.7 and 5.6 °C for the July temperature and mean treatment season temperature, respectively. The logistic regression was applied to each community (except Sanikiluaq) in Nunavut using historic climate data and a probability of microalgae growth was calculated. Based on the model results, soluble phosphorus concentrations consistent with secondary treatment could be achieved if WSP depth is less than 2 m. The model demonstrated a robust method to predict whether a microalgae bloom will occur under a range of model parameters.

Benzophenone-4 (BP4), as the raw material of common sunscreen products, usually shows strong eco-toxicity and endocrine-disrupting activity in aquatic animals. However, the potential adverse effect of BP4 on aquatic vegetation is still unclear. In order to evaluate the inhibitory effect of BP4 on phytoplankton, wild and acclimated Chlorella vulgaris was used as representative aquatic plant cells and experimental studies were conducted on the characteristics of its growth and cellular metabolisms upon exposure to elevated BP4 concentrations (1, 5, 10, 20, 50, and 100 mg L -1 ). C. vulgaris basically appeared low sensitivity to BP4 exposure because the 96-h EC 50 was measured as 65.16 mg L -1 for its wild type. The 96-h EC 50 of the acclimated type, which was pre-exposed to 10 mg L -1 of BP4 and transferred twice, was 140.76 mg L -1 . By cellular response tests regarding non-enzymatic antioxidants carotenoid content, malondialdehyde (MDA), enzyme antioxidant superoxide dismutase (SOD) activity, and the photosynthetic efficiency, it was clarified that increasing exposure concentration elevated the hindrance to cellular metabolism. However, the rate of BP4 utilization as substrates for C. vulgaris growth showed a trend of decreasing with increasing BP4 concentration. The higher 96-h EC 50 value of the acclimated C. vulgaris to BP4 inhibition than the wild C. vulgaris showed the enhanced tolerance capability; however, the continuous stress response of acclimated type should be taken into account when using microalgae species for toxicity assessment.

Microalgae cultivation is a promising approach to remove ambient CO 2 via photosynthesis process. This paper investigates the impact of high CO 2 concentrations (6, 12, and 16%) on algae growth, CO 2 biofixation, lipid and carbohydrate contents, and nutrient removal of newly isolated microalgae, Coelastrum sp. SM. In addition, the ability of microalgae to produce biodiesel at optimal condition was studied. The microalgae were cultivated in wastewater using an airlift photobioreactor. Under 12% CO 2 , the maximum biomass productivity and CO 2 fixation rate were 0.267 g L -1  day -1 and 0.302 g L -1  h -1 , respectively. Total Kjeldahl nitrogen (TKN), total phosphorous (TP), nitrate, and sCOD removal efficiency were 84.01, 100, 86.811, and 73.084%, respectively. Under 12% CO 2 and at the same condition for cell growth, the highest lipid and carbohydrate contents were 3 7.91 and 58.45%, respectively. The composition of fatty acids methyl ester (FAME) of the microalga lipid was defined. Based on the obtained results and FAME profile, Coelastrum sp. SM was a suitable feedstock for biodiesel production and also, the organism had a great potential for CO 2 biofixation, which is also more suitable than any other reported strains in other related studies.

The present work studies the removal of nutrients (nitrate and phosphate) from a synthetic wastewater simulating a secondary treatment effluent using the microalgae Chlorella vulgaris in autotrophic photobioreactors, together with an analysis of the critical points affecting the scaling-up process from laboratory to pilot scale. Laboratory experiments were done in open agitated 1-L photobioreactors under batch operation mode, while pilot-scale experiments were done using a 150-L closed tubular photobioreactor under continuous operation mode. In both scales, nitrate was the limiting substrate and the effect of its concentration on microalgae performance was studied. From laboratory experiments, an average microalgae productivity of 85 mg VSS  L -1  day -1 and approximate maximum N-NO 3 - and P-PO 4 3- removal rates of 8 mg N g VSS -1  day -1 , and 2.6 mg P g VSS -1  day -1 were found. Regarding pilot scale, the average microalgae productivity slightly decreased (76 mg VSS  L -1  day -1 ) while the approximate maximum N-NO 3 - and P-PO 4 3- removal rates slightly were increased (11.7 mg N g VSS -1  day -1 and 3.04 mg P g VSS -1  day -1 ) with respect to the laboratory-scale results. The pilot-scale operation worked under lower levels of turbulence and higher dissolved oxygen concentration and light intensity than laboratory experiments; those parameters were difficult to control and they can be identified as the critical points in the differences found on both nutrient removal and microalgae production.

The use of human and animal wastes for fertilization of aquaculture ponds has been practiced for thousands of years. In the present work, we have used the excreta (human urine, poultry waste, cow dung, and urine) as a nutrient source for the cultivation of Chlorella singularis, Micractinium pusillum, and Chlorella sorokiniana strains of microalgae. Different solid wastes were treated with 60 mM H 2 SO 4 for the extraction of nutrients. After treatment, the supernatant of different solid wastes and liquid waste were diluted 5, 10, 15, and 20% to be used as a media for the cultivation of microalgae. Chlorella sorokiniana was able to grow in all concentration of excreta media. The maximum growth rate 140 ± 3.1 mg/L/day and lipid production (45.5 ± 2.3 mg/L/day) was obtained in 20% poultry. Among the different excreta media used for cultivation of microalgae, poultry media displayed the best results and thus, should be used for large scale cultivation of microalgae.

A systematic study of the effect of nitrogen levels in the cultivation medium of Chlorella vulgaris microalgae grown in photobioreactor (PBR) on biomass productivity, biochemical and elemental composition, fatty acid profile, heating value (HHV), and composition of the algae-derived fast pyrolysis (bio-oil) is presented in this work. A relatively high biomass productivity and cell concentration (1.5 g of dry biomass per liter of cultivation medium and 120 × 10 6 cells/ml, respectively) were achieved after 30 h of cultivation under N-rich medium. On the other hand, the highest lipid content (ca. 36 wt.% on dry biomass) was obtained under N-depletion cultivation conditions. The medium and low N levels favored also the increased concentration of the saturated and mono-unsaturated C16:0 and C18:1(n-9) fatty acids (FA) in the lipid/oil fraction, thus providing a raw lipid feedstock that can be more efficiently converted to high-quality biodiesel or green diesel (via hydrotreatment). In terms of overall lipid productivity, taking in consideration both the biomass concentration in the medium and the content of lipids on dry biomass, the most effective system was the N-rich one. The thermal (non-catalytic) pyrolysis of Chlorella vulgaris microalgae produced a highly complex bio-oil composition, including fatty acids, phenolics, ethers, ketones, etc., as well as aromatics, alkanes, and nitrogen compounds (pyrroles and amides), originating from the lipid, protein, and carbohydrate fractions of the microalgae. However, the catalytic fast pyrolysis using a highly acidic ZSM-5 zeolite, afforded a bio-oil enriched in mono-aromatics (BTX), reducing at the same time significantly oxygenated compounds such as phenolics, acids, ethers, and ketones. These effects were even more pronounced in the catalytic fast pyrolysis of Chlorella vulgaris residual biomass (after extraction of lipids), thus showing for the first time the potential of transforming this low value by-product towards high added value platform chemicals.

This article investigates the innovative attached cultivation of Chlorella vulgaris (C. vulgaris) using different materials as an alternative to high capital techniques of harvesting such as centrifugation, flocculation, and filtration. A simple attached algal cultivation system was proposed that was equipped by 10 submerged supporting materials which can harvest algal cells, efficiently. The effect of operational parameters such as light intensity, the rate of aeration, and auto-harvesting time was investigated. A chip, durable, and abundant cellulosic material (Kaldnes carriers covered by kenafs, KCCKs) was proposed for auto-harvesting C. vulgaris cells. The results revealed that optimum aeration rate, light intensity, and auto-harvesting of microalgal cells were 3.6 vvm, 10,548 W/m 2 , and 12 days, respectively. Six of these KCCKs had the highest biofilm formation percent up to 33%. In this condition, the rate of cell growth increased to 0.6 mg/cm 2 . Therefore, this system can be used for appropriate auto-harvesting of microalgae in the attached growth systems. C. vulgaris biomass composition is valuable for biodiesel, bioethanol, and animal protein production.

Four microalgal strains, namely, Tetraselmis indica (T. indica), Scenedesmus abundans (S. abundans), Spirulina sp., and Nostoc muscorum (N. muscorum) were cultivated on four different wastewaters in 1000 ml photobioreactors with 750 ml working volume under 94.5 μmol m -2  s -1 light intensity for 14 days for phycoremediation of wastewaters and sustainable biodiesel production. These microalgal strains attained maximum biomass growth in the secondary treated sewage (STS). Maximum biomass yield (0.6533 g L -1 ) and lipid productivity (25.44 mg L -1  d -1 ) for T. indica were achieved in STS. T. indica removed (63.6-78.24%) of nitrate, (60.90-65.97%) of phosphate, (61.01-80.01%) of ammonical nitrogen, and (71.16-85.70%) of total organic carbon (TOC) in all four wastewaters. The fatty acid methyl ester (FAME) profile of T. indica shows the presence of myristic acid (1.2%) pentadecylic acid (0.28%), palmitic acid (10.32%), oleic acid (34.59%), linoleic acid (12.38%), and eicosanoic acid (14.88%) in STS. This study demonstrates that T. indica is the most suitable microalgal species among the four microalgal strains selected for phycoremediation of wastewaters and higher biomass production for sustainable biodiesel production.

Much endeavor has been dispensed recently to evaluate the potential of CO 2 mitigation by microalgae. We introduce an alternative, novel, LED-illumination isothermal microcalorimetric method to assess the thermodynamic behaviors of microalgae for better understanding of their carbon sequestration capacity. Microalgae thermodynamic behaviors were recorded as power-time curves, and their indices such as total heat evolution (Q T ), maximum power output (P max ) and heat generated by per algae cell (J N/Q ) were obtained. The values for highest (74.80 g L -1 ) and control sample (0.00 g L -1 ) of Q T , P max and J N/Q were 20.85 and 2.32 J; 252.17 and 57.67 μW; 7.91 ×  -06 and 8.80 ×  -07  J cell -1 , respectively. According to the values of Q T , a general order to promote the CO 2 sequestration was found at 74.8 g L -1  > 29.92 g L -1  > 14.96 g L -1  > 7.48 g L -1  > 0 g L -1 of C sources, which directly corresponded to carbon availability in the growth medium. Chlorella vulgaris GIEC-179 showed the highest peak P max at 74.8 g L -1 concentration which was directly transformed to their biomass during bio-fixation of CO 2 process. This study is applicable for better understanding of CO 2 fixation performance of algae.

The pure cultures of microalgae Chlorella vulgaris ATCC 13482 and Scenedesmus obliquus FACHB 417 were grown in municipal wastewater in 7-L airlift bubble column photobioreactor supplied with 5% CO 2 /air (v/v). Batch experiments were conducted at 25 °C with 14-h light/10-h dark cycle for a period of 10 days. The CO 2 capture efficiencies for both the microalgae were monitored in terms of their respective biomass productivities, carbon contents, and CO 2 consumption rates. In the present study, the initial concentration of ammonia (43.7 mg L -1 ) was decreased to 2.9 and 3.7 mg L -1 by C. vulgaris and S. obliquus, respectively. And, the initial concentration of phosphate (18.5 mg L -1 ) was decreased to 1.1 and 1.6 mg L -1 by C. vulgaris and S. obliquus, respectively. CO 2 biofixation rates by C. vulgaris and S. obliquus, cultivated in municipal wastewater, were calculated to be 140.91 and 129.82 mg L -1  day -1 , respectively. The findings from the present study highlight the use of microalgae for wastewater treatment along with CO 2 uptake and biomass utilization for pilot scale production of biodiesel, biogas, feed supplements for animals, etc., thus minimizing the production costs.

Microalgae-based treatment systems have been successfully used for the polishing of domestic wastewater. Research is underway in studying the suitability of using these systems as main treatment units. This study focuses on comparing the performances of a mixed microalgal culture and an aerobic bacterial culture, based on the kinetic evaluation, in removing organic carbon from a kitchen wastewater. The two systems were operated at six different solid retention times (SRTs)-2, 4, 6, 8, 10, and 12 days in continuous mode. The influent and effluent samples were analyzed for chemical oxygen demand (COD), total organic carbon (TOC), total nitrogen (TN), phosphates, and surfactants. Steady-state kinetics (k, K s , Y, and k d ) for organic carbon removal were obtained by fitting experimental data in linearized Michaelis-Menten and Monod equations. The mixed microalgal system showed similar or better performance in COD and TN removal (88 and 85%, respectively) when compared with the COD and TN removal by the aerobic bacterial system (89 and 48%). A maximum lipid yield of 40% (w/w of dry biomass) was observed in the microalgal system. Saturated fatty acids accounted for 50% of the total observed FAME species. The study indicates that the mixed microalgal culture is capable of treating kitchen wastewater and has the potential to replace aerobic bacteria in biological treatment systems in certain cases.

Green microalgae colonizing stone surfaces represent a major problem for the conservation of heritage monuments, since they lead to biodegradation and aesthetic issues. Previous studies in La Glacière show cave (France) have demonstrated that UV-C may have a strong effect on microalgae, thus leading to chlorophyll bleaching, which was increased when biofilms were maintained under VIS-light condition unlike to those maintained in the dark. To understand the physiological mechanisms underlying this response and in order to optimize in situ treatment, 30 kJ m -2 UV-C exposure times were applied to Chlorophyta Chlorella sp. and chlorophyll degradation kinetics were then monitored. UV-C irradiation was enough to inhibit photosynthesis and to directly kill all algal cells. Results also showed that chlorophyll a was degraded faster than chlorophyll b and that 14 h were necessary for complete degradation of all the present chlorophyll. In addition, our results highlighted the importance of visible light exposition after UV-C treatment which leading to chlorophyll bleaching. Irradiated algae cultivated in the dark were still green 5 days after treatment while cultivated samples in the light lost their green color after 14 h. An efficient UV-C treatment applicable to show caves and other heritage monuments was proposed.

To investigate the combined toxicities of copper nanoparticles (nano-Cu) with carbon nanotubes (CNTs) on marine microalgae Skeletonema costatum, algal growth inhibition tests were carried out. Toxicities of nano-Cu with CNTs and without CNTs on microalgae were determined, respectively. Chlorophyll content and photosynthetic efficiency (ΦPSII) were determined to compare negative effects of nano-Cu with CNTs and without CNTs on photosynthesis. The concentration of Cu 2+ released by nano-Cu into the medium was determined, and interactions between nano-Cu and CNTs were analyzed to study toxic mechanisms of combined toxicities of nano-Cu with CNTs. It was found that both nano-Cu and CNTs could inhibit the growth of the microalgae; however, the toxicity of CNTs on the microalgae was far lower than that of nano-Cu. The maximum growth inhibition ratio (IR) of nano-Cu on the microalgae was 86% appearing at 96 h under 1.0 mg/L nano-Cu treatment, while the maximum IR of CNTs on the microalgae was 58% at 96 h under 200 mg/L CNT treatment. CNTs could reduce the toxicity of nano-Cu on the microalgae in processes of growth and photosynthesis. Adsorption of Cu 2+ on CNTs and aggregate between Cu and CNTs in the medium were main reasons for attenuation of toxicity of nano-Cu with adding CNTs.

Liquid digestate (LD) is highly turbid and contains ammonium (NH 4 + -N), which negatively influences microalgal growth. Therefore, a method of reducing LD turbidity and NH 4 + -N content is proposed, using struvite precipitation. To obtain struvite precipitation supernatant with an ideal UV transmittance, NH 4 + -N concentration, and N/P ratio for microalgal growth, the effects of pH and the molar ratio of NH 4 + /Mg 2+ /PO 4 3- were studied. Results show that the optimal NH 4 + /Mg 2+ /PO 4 3- molar ratio was 1:1.5:1.5, with a pH value of 8.5, following NaOH addition. Gray relational analysis (GRA) was applied to obtain a relative gray scale for the evaluation of multiple outputs. Results show that Chlorella regularis FACHB-1068 was the optimal microalgae species to support growth in the struvite precipitation supernatant. Using struvite precipitation and treatment with cultured C. regularis FACHB-1068 for 7 days, the removal efficiencies of NH 4 + -N, PO 4 3- -P, and COD in LD were 96.52, 99.33, and 35.30%, respectively.

Microalga-derived biodiesel plays a crucial role in the sustainable development of biodiesel in recent years. Literature related to microalga-derived biodiesel had an increasing trend with the expanding research outputs. Based on the Science Citation Index Expanded (SCI-Expanded) of the Web of Science, a bibliometric analysis was conducted to characterize the body of knowledge on microalga-derived biodiesel between 1993 and 2016. From the 30 most frequently used author keywords, the following research hotspots are extracted: lipid preparation from different microalga species, microalga-derived lipid and environmental applications, lipid-producing microalgae cultivation, microalgae growth reactor, and microalga harvest and lipid extraction. Other keywords, i.e., microalga mixotrophic cultivation, symbiotic system between microalga and other oleaginous yeast, microalga genetic engineering, and other applications of lipid-producing microalga are future focal points of research. Graphical abstract.

Previous studies showed that methanol extracts from Porphyra yezoensis significantly inhibited Karenia mikimitoi and Skeletonema costatum. Five sesquiterpenoids (1-5) were successfully isolated from this marine macroalga through a combination of silica gel column chromatography and repeated preparative thin-layer chromatography in this paper. Their structure was identified as gossonorol (1), 7,10-epoxy-ar-bisabol-11-ol (2), cyclonerodiol (3), cadinol, (4) and 4-cadinen-1-ol (5) on the basis of spectroscopic data. These sesquiterpenoids were isolated from Porphyra yezoensis for the first time, and cyclonerodiol (3) and cadinol (4) isolated from marine macroalgae for the first time. Further, a quantitative relationship between the inhibition of algal growth and the concentration of each antialgal sesquiterpenoid (gossonorol, 7,10-epoxy-ar-bisabol-11-ol and cyclonerodiol) was determined and important parameters, e.g., EC 50-96h for future practical HAB control are to be obtained. Results showed that three sesquiterpenoids (1-3) had selective antialgal activity against the growth of red tide microalgae (Amphidinium carterae, Heterosigma akashiwo, Karenia mikimitoi, Phaeocystis globosa, Prorocentrum donghaiense, and Skeletonema costatum). More than two test red tide microalgae were significantly inhibited by these three sesquiterpenoids (1-3). Their antialgal activity against red tide microalgae has not been previously reported. Furthermore, EC 50-96h of gossonorol (1) and 7,10-epoxy-ar-bisabol-11-ol (2) for specific test red microalgae were not only significantly less than 10 μg/mL, but also were smaller than/or very close to those of potassium dichromate. Gossonorol (1) and 7,10-epoxy-ar-bisabol-11-ol (2) possessed good application potential than potassium dichromate as a characteristic antialgal agent against the specific harmful red tide microalgae (Heterosigma akashiwo, Phaeocystis globosa, and Prorocentrum donghaiense) (or Heterosigma akashiwo and Karenia mikimitoi).

Microalgae can effectively absorb nitrogen (N) and phosphorus (P) in wastewater, while growth characteristics can be affected by such nutrients. The influences of the N and P concentration on growth, biomass yield, protein yield, and cell ultrastructure of Chlamydomonas reinhardtii (C. reinhardtii) were investigated in this study. The results showed that, in the optimum conditions (24-72 mg/L for N and 4.5-13.5 mg/L for P), the final biomass and protein content of C. reinhardtii could reach maximum value, and the cell organelles (chloroplast, mitochondria,etc.) showed good structures with larger chloroplasts, and more and neater thylakoids. However, if the concentration of nutrients was much higher or lower than the optimal value, it would cause adverse effects on the growth of C. reinhardtii, especially in high nitrogen (1000 mg/L) and low phosphorus (0.5 mg/L) conditions. Under these extreme conditions, the ultrastructure of the cells was also damaged significantly as follows: the majority of the organelles were deformed, the chloroplast membrane became shrunken, and the mitochondria became swollen, even partial disintegrated (differing slightly under high-N and low-P conditions); furthermore, it is found that C. reinhardtii was more sensitive to low-P stress. On the basis of these results, our findings have general implications in the application of wastewater treatment.

Lake water level fluctuations (WLF) are an important factor driving the selection and seasonal dynamics of phytoplankton and potentially toxigenic cyanobacteria. Nevertheless, the relative importance of environmental drivers connected to WLF may be completely different, depending on the typology and use of waterbodies, latitude and climatic regimes. In this study, we investigated the impact of WLF in a large subtropical reservoir in south-eastern China (Hongfeng Reservoir, Guizhou Province). The study was based on monthly samplings carried out in 2014 in six stations. The strong increase in the water level observed in early summer caused a radical shift in the phytoplankton community. While in the pre-flooding period phytoplankton was composed of large diatoms, chrysophytes and Oscillatoriales (mostly Limnothrix sp.), the post-flooding period showed an increase in smaller and more competitive chlorophytes, smaller diatoms and cryptophytes better adapted to a fast colonisation of new and nutrient-rich environments. The environmental drivers that drove the change were dilution, flushing and interference with the seasonal water stratification processes. We concluded that, because WLF represents a complex variable integrating different physical effects in one explanatory descriptor, its value as a predictor of phytoplankton and cyanobacteria dynamics in lake ecosystems is difficult to generalise and needs to be investigated on a case-by-case basis. For this reason, considering the year-to-year hydrological variability that potentially characterise reservoirs, definite indications for management should be outlined considering more than 1-year study.

A coupling technique to purify wastewater for lipid production based on microalgae is attractive and promising for its potential to clean water and as biofuel feedstocks. Metal ions from wastewater might be involved in microalgal cultivation. In this study, the effects of metal ions on algal growth, lipid-producing potential, and water purifying capability of Chlorella sp. HQ were investigated. The effects of metal ions (Cr 6+ , Cu 2+ , Mn 2+ , Zn 2+ , Fe 3+ , Na + , and K + ) on alga lipid production combined with water purification showed that Chlorella sp. HQ had strong resistance to metal ions and could efficiently remove them (Fe 3+ 85.40~98.73%, Mn 2+ 45.63~97.24%, Zn 2+ 81.93~100.00%, Cu 2+ 81.71~95.19%, Cr 6+ 20.07~45.60%). Meanwhile, nutrient removal (total nitrogen (TN) 78.15~94.77%, total phosphorus (TP) 80.52~100%) was not inhibited by metal ions. Besides that, the highest algal biomass, lipid yield, and triacylglycerol (TAG) yield peaked at 350.00 ± 31.50, 87.50 ± 3.54, and 33.39 ± 19.42 mg L -1 , respectively, with the addition of Fe 3+ (6.6 mg L -1 ), Na + (101.81 mg L -1 ), and K + (31.9 mg L -1 ). The lipid/TAG content significantly increased up to 54.17 ± 11.91%/44.92 ± 0.42%, 100%/100%, 32.56 ± 12.40%/37.53 ± 4.58%, and 77.50 ± 1.77%/46.19 ± 1.06%, separately, with the addition of Cr 6+ (0.50 mg L -1 ), Cu 2+ (5.02 mg L -1 ), Zn 2+ (5.05 mg L -1 ), and Mn 2+ (50.52 mg L -1 ).

Environmental building recommendations aimed towards new environmental policies and management-changing decisions which as example demonstrated in consideration of the problems of Canadian oil sands operators. For the implementation of the circular economic strategy, we use an in-depth analysis of reported environmental after-consequence on all stages of the production process. The study addressed the promotion of innovative solutions for greenhouse gas emission, waste mitigation, and risk of falling in oil prices for operators of oil sands with creating market opportunities. They include the addition of microalgae biomass in tailings ponds for improvement of the microbial balance for the water speedily cleaning, recycling, and reusing with mitigation of GHG emissions. The use of food scraps for the nutrition of microalgae will reduce greenhouse gas emission minimally, on 0.33 MtCO 2 eq for Alberta and 2.63 MtCO 2 eq/year for Canada. Microalgae-derived biofuel can reduce this emission for Alberta on 11.9-17.9 MtCO 2 eq and for Canada on 71-106 MtCO 2 eq/year, and the manufacturing of other products will adsorb up to 135.6 MtCO 2 and produce 99.2 MtO 2 . The development of the Live Conserve Industry and principal step from non-efficient protection of the environment to its cultivation in a large scale with mitigation of GHG emission and waste as well as generating of O 2 and value-added products by the use of microalgae opens an important shift towards a new design and building of a biological system.

The present study investigated the performance of an integrated system, combining the sequential use of microalgae (MA) and vertical flow constructed wetland (VFCW) for the treatment of wastewaters produced at a university campus. Ecotoxicity and phytotoxicity assays were performed using respectively Daphnia magna and Lactuca sativa, whereas the genotoxicity of the wastewaters was assessed by using D. magna and Allium cepa. The results revealed that the major environmental impacts of the studied wastewaters are associated with the high eutrophication potential, due to high N-NH 3 (68.8 ± 25.7 mg L -1 ), total P (7.71 ± 2.5 mg L -1 ), and BOD 5 (526.4 ± 177 mg L -1 ) values, pathogenic load, and genototoxicity (p < 0.0001). The results also showed that the integrated system (MA + VFCW) was not able to satisfactory reduce the total p values (only 4%). Nevertheless, the MA + VFCW system achieved very promising results for the nitrogen removal, with emphasis on N-NH 3 removal (100%) and the highest BOD 5 removal (57%). Neither the raw wastewaters nor the treated wastewaters were phytotoxic. The integrated system completely eliminated the ecotoxicity (100%) and genotoxicity (n.s.) of the raw wastewater and showed decontamination potential. Thus, the integrated system emerges as an innovative environmental technology and, with minor adjustments, might be efficiently used in large scale and eventually replace conventional wastewater treatment systems.

Biodiesel wash water is a contaminating industrial effluent that must be treated prior to disposal. The use of this effluent as a low-cost alternative cultivation medium for microalgae could represent a viable supplementary treatment. We cultivated 11 microalgae species with potential use for biodiesel production to assess their growth capacities in biodiesel industrial washing waters. Only Monoraphidium contortum, Ankistrodesmus sp., Chlorococcum sp., and one unidentified Chlorophyceae species grew effectively in that effluent. M. contortum showed the highest growth capacity and had the second highest fatty acid content (267.9 mg g -1 of DW), predominantly producing palmitic (20.9%), 7,10,13-hexadecatrienoic (14%), oleic (16.2%), linoleic (10.5%), and linolenic acids (23.2%). In the second phase of the experiment, the microalgae were cultivated in biodiesel wash water at 75% of its initial concentration as well as in WC (control) medium. After 21 days of cultivation, 25.8 and 7.2% of the effluent nitrate and phosphate were removed, respectively, and the chemical oxygen demand was diminished by 31.2%. These results suggest the possibility of cultivating biodiesel producing microalgae in industrial wash water effluents.

Within the context of global climate changes, it is expected that low-lying coastal freshwater ecosystems will face seawater intrusion with concomitant increase in salinity levels. Increased salinity may provoke disruption of competitive relationships among freshwater species. However, species may be capable of acclimating to salinity, which, in turn, may influence the resilience of ecosystems. Accordingly, this work aimed at assessing the effects of multigenerational exposure to low levels of salinity in the competitive outcome of two species of green microalgae: Raphidocelis subcapitata and Chlorella vulgaris. To attain this, three specific objectives were delineated: (1) compare the toxicity of natural seawater (SW) and NaCl (as a surrogate of SW) to the two microalgae, (2) determine the capacity of the two microalgae species to acclimate to low salinity levels, and (3) assess the influence of exposure to low salinity levels in the competitive outcome of the two microalgae. Results revealed SW to be slightly less toxic than NaCl for the two microalgae. The EC 25,72 h for growth rate was 4.63 and 10.3 mS cm -1 for R. subcapitata and 6.94 and 15.4 mS cm -1 for C. vulgaris, respectively for NaCl and SW. Both algae were capable of acclimating to low levels of salinity, but C. vulgaris seemed to acclimate faster than R. subcapitata. When exposed in competition, under control conditions, the growth rates of C. vulgaris were lower than those of R. subcapitata. However, C. vulgaris was capable of acquiring competitive advantage equaling or surpassing the growth rate of R. subcapitata with the addition of NaCl or SW, respectively. The multigenerational exposure to low levels of salinity influenced the competitive outcome of the two algae both under control and salinity exposure. These results suggest that long-term exposure to low salinity stress can cause shifts in structure of algae communities and, therefore, should not be neglected since algae are at the basis of food web constituting important energetic resources to higher trophic levels.

Periphyton is ubiquitous in paddy field, but its importance in influencing the bioavailability of phosphorus (P) in paddy soil has been rarely recognized. A paddy field was simulated in a greenhouse to investigate how periphyton influences P bioavailability in paddy soil. Results showed that periphyton colonizing on paddy soil greatly reduced P content in paddy floodwater but increased P bioavailability of paddy soil. Specifically, all the contents of water-soluble P (WSP), readily desorbable P (RDP), algal-available P (AAP), and NaHCO 3 -extractable P (Olsen-P) in paddy soil increased to an extent compared to the control (without periphyton) after fertilization. In particular, Olsen-P was the most increased P species, up to 216 mg kg -1 after fertilization, accounting for nearly 60 % of total phosphorus (TP) in soil. The paddy periphyton captured P up to 1.4 mg g -1 with Ca-P as the dominant P fraction and can be a potential crop fertilizer. These findings indicated that the presence of periphyton in paddy field benefited in improving P bioavailability for crops. This study provides valuable insights into the roles of periphyton in P bioavailability and migration in a paddy ecosystem and technical support for P regulation.

In this study, the effect of flue gas CO2 on growth, lipid production, and fatty acid composition of a green microalga Acutodesmus obliquus KGE 30 was investigated. The highest growth rate (0.46 g L(-1) and μmax = 1.09 day(-1)), total inorganic carbon removal (95.9 mg L(-1)), and lipid productivity (20.1 mg L(-1) day L(-1)) was obtained at 14.1 % CO2 after 4 days of cultivation. In a semicontinuous batch reactor, the highest biomass production (1.19 g L(-1)) was achieved after 12 days with continuous injection of flue gas CO2. Compared with synthetic CO2, fatty acid methyl ester analysis showed that the amount of unsaturated fatty acid increased by 19.2 % with 14.1 % flue gas CO2. The application of flue gas CO2 improved biomass production and lipid productivity in A. obliquus. The current investigation demonstrated that the use of flue gas CO2 could reduce the cost of microalgae biomass production for better biofuel generation.

In a present study, nutrient removal from municipal wastewater by Chlorella vulgaris and Nannochloropsis oculata was investigated by using mixotrophic cultivation with glycerol (0 to 5 g/L). Performance parameters were assessed by estimating the removal of total nitrogen, total phosphorus, chemical oxygen demand (COD), biomass growth, chlorophyll content, lipid yield, and fatty acids. With the addition of 2 g/L glycerol, a maximum biomass productivity of 56 mg/L/day was achieved in the mixotrophic culture of C. vulgaris within 12 days. The mixotrophic culture showed a 30-fold increase in biomass productivity compared to the wastewater without any glycerol. However, the highest total nitrogen removal (80.62 %), total phosphate removal (60.72 %), and COD removal (96.3 %) was observed in the N. oculata culture supplemented with 3, 5, and 1 g/L glycerol, respectively. These results suggest that mixotrophic cultivation using glycerol offers great potential in the production of renewable biomass, waste water treatment, and consequent production of high-value microalgal oil. Graphical Abstract Simultaneous biomass production and nutrient removal using microalgae cultivated in wastewater supplemented with glycerol.

The potential of microalgae consortia used in dairy wastewater treatment combined with microalgae biodiesel feedstock production was evaluated by comparing the nutrient removal of dairy wastewater, the growth of cells, and the lipid content and composition of biomass between monoalgae and microalgae consortia cultivation system. Our results showed that higher chemical oxygen demand (COD) removal (maximum, 57.01-62.86 %) and total phosphorus (TP) removal (maximum, 91.16-95.96 %) were achieved in almost microalgae consortia cultivation system than those in Chlorella sp. monoalgae cultivation system (maximum, 44.76 and 86.74 %, respectively). In addition, microalgae consortia cultivation except the mixture of Chlorella sp. and Scenedesmus spp. reached higher biomass concentration (5.11-5.41 g L(-1)), biomass productivity (730.4-773.2 mg L(-1) day(-1)), and lipid productivity (143.7-150.6 mg L(-1) day(-1)) than those of monoalgae cultivation (4.72 g L(-1), 674.3, and 142.2 mg L(-1) day(-1), respectively) on the seventh day. Furthermore, the fatty acid methyl ester (FAME) profiles indicated the lipids produced from microalgae consortia cultivation system were more suitable for biodiesel production. The microalgae consortia display superiority in dairy wastewater treatment and the getting feedstock for biodiesel production.

Microalgae possess the ability to grow and glean nutrients from wastewater; such wastewater-grown biomass can be used as a biofertilizer for crops. The present investigation was undertaken to evaluate two formulations (formulation with unicellular microalgae (MC1) and formulation with filamentous microalgae (MC2); T4 and T5, respectively), prepared using wastewater-grown microalgal biomass, as a biofertilizer (after mixing with vermiculite/compost as a carrier) in wheat crop (Triticum aestivum L. HD2967) under controlled conditions. The highest values of available nitrogen (N), phosphorus (P), and potassium (K) in soil and nitrogen-fixing potential were recorded in treatment T5 (75% N + full-dose PK + formulation with filamentous microalgae (MC2). Microbial biomass carbon was significantly enhanced by 31.8-67.0% in both the inoculated treatments over control (recommended dose of fertilizers), with highest values in T4 (75% N + full-dose PK + formulation with unicellular microalgae (MC1)). Both the microalgal formulations significantly increased the N, P, and K content of roots, shoots, and grains, and the highest total N content of 3.56% in grains was observed in treatment T5. At harvest stage, the treatments inoculated with microalgal formulations (T4 and T5) recorded a 7.4-33% increase in plant dry weight and up to 10% in spike weight. The values of 1000-grain weight showed an enhancement of 5.6-8.4%, compared with T1 (recommended doses of fertilizers). A positive correlation was observed between soil nutrient availability at mid crop stage and plant biometrical parameters at harvest stage. This study revealed the promise of such microalgal consortia as a biofertilizer for 25% N savings and improved yields of wheat crop.

In the present study, we investigated structural effects of various ionic liquids (ILs) on microalgal growth inhibition and microbial biodegradability. For this, we tested pyridinium- and pyrrolidinium-based ILs with various alkyl chain lengths and bromide anion, and compared the toxicological effects with log EC50 values of imidazolium-based IL with the same alkyl chains and anion from literature. Comparing determined EC50 values of cationic moieties with the same alkyl chain length, pyridinium-based ILs were found to be slightly more toxic towards the freshwater green alga, Pseudokirchneriella subcapitata, than a series of pyrrolidinium and imidazolium except to 1-octyl-3-methylimidazolium bromide. Concerning the biodegradation study of 12 ILs using the activated sludge microorganisms, the results showed that the pyridinium derivatives except to 1-propyl-3-methylpyridinium cation were degraded. Whereas in case of imidazolium- and pyrrolidinium-based compounds, only n-hexyl and n-octyl substituted cations were fully degraded but no significant biodegradation was observed for the short chains (three and four alkyl chains).

A comparative evaluation of the removal of benzo(a)pyrene (BaP) by sorption and degradation by two microalgal species, Selenastrum capricornutum and Scenedesmus acutus was performed. The monitoring of the amount of BaP remaining in the liquid culture media and the biomass along with the appearance of three metabolites (4,5 dihydrodiol-BaP; 7,8-dihydrodiol-BaP; and 9,10 dihydrodiol-BaP) at short time periods (from 0.25 to 72 h) in cultures exposed to BaP was made by high-performance liquid chromatography (HPLC) with fluorescence and UV detection. Complete removal of BaP was achieved by the two live microalgal species: S. capricornutum at 15 h of exposure (99%) and S. acutus at 72 h of exposure (95%). Sorption is an important phenomenon for BaP removal by S. capricornutum but biodegradation is the principal means of removing BaP in live cells. The formation of metabolites by S. capricornutum is rapid and seems to be proportional to the amount of the BaP added to cultures. In contrast, in these bioassays, most of the BaP removal of S. acutus is due to sorption rather than degradation. The appearance of metabolites in the cultures is very slow and at a low amount compared to cultures of S. capricornutum. The similarities and differences existing between the two microalgae are important for the establishment of the conditions for bioremediation.

Ten compounds (1~10) were successfully isolated from green algae Ulva prolifera through the combination of silica gel column chromatography, Sephadex LH-20 column chromatography and repeated preparative thin-layer chromatography. These ten compounds showed antialgal activity against red tide microalgae. Among them, compounds 3, 6, and 7 showed stronger antialgal activity against red tide microalgae. Furthermore, their structure was identified on the basis of spectroscopic data. There are three glycoglycerolipids: 1-O-octadecanoic acid-3-O-β-D-galactopyranosyl glycerol (2), 1-O-palmitoyl-3-O-β-D-galactopyranosyl glycerol (4), and 1-O-palmitoyl-2-O-oleoyl-3-O-β-D-galactopyranosyl glycerol (5); two monoglycerides: glycerol monopalmitate (1), 9-hexadecenoic acid, 2,3-dihydroxypropyl ester (3); two terpenoids: loliolide (6) and lsololiolide (7); one lipid-soluble pigments: zeaxanthin (8); one sterol: cholest-5-en-3-ol (9); and one alkaloid: pyrrolopiperazine-2,5-dione (10). These compounds were isolated from U. prolifera for the first time, and compounds 2, 3, 5, and 8 were isolated from marine macroalgae for the first time.

The effect of insecticides (acephate and imidacloprid) on a freshwater microalga Chlamydomonas mexicana was investigated with respect to photosynthetic pigments, carbohydrate and protein contents, fatty acids composition and induction of stress indicators including proline, superoxide dismutase (SOD) and catalase (CAT). C. mexicana was cultivated with 1, 5, 10, 15, 20 and 25 mg L(-1) of acephate and imidacloprid. The microalga growth increased with increasing concentrations of both insecticides up to 15 mg L(-1), beyond which the growth declined compared to control condition (without insecticides). C. mexicana cultivated with 15 mg L(-1) of both insecticides for 12 days was used for further analysis. The accumulation of photosynthetic pigments (chlorophyll and carotenoids), carbohydrates and protein was decreased in the presence of both insecticides. Acephate and imidacloprid induced the activities of superoxide dismutase (SOD) and catalase (CAT) and increased the concentration of proline in the microalga, which play a defensive role against various environmental stresses. Fatty acid analysis revealed that the fraction of polyunsaturated fatty acids decreased on exposure to both insecticides. C. mexicana also promoted 25 and 21% removal of acephate and imidacloprid, respectively. The biochemical changes in C. mexicana on exposure to acephate and imidacloprid indicate that the microalga undergoes an adaptive change in response to the insecticide-induced oxidative stress.