Search

Advantages and disadvantages of the concept of an industrial complex are discussed. From an environmental standpoint an ideal industrial complex is one containing a group of compatible industrial plants utilizing completely each other's wastes and products as raw materials and manufacturing products with no adverse environmental impact and at a minimum of cost. A typical complex centering about a pulp and papermill is pictured in this paper. This complex produces six products for external sale and four products for internal use. In addition, all major wastes of suspended solids, cooking liquor, fillers, heat and bark are reused within the complex in the manufacture of these products. A literature review evolved typical concentrations of recoverable suspended solids in various process effluents. A mass balance was prepared assuming that the total production of fine paper is 907.2 kg × 103 (1000 tons) per day. Little or no air or water pollution results from this complex. In addition, it is anticipated that no expensive waste-water treatment plant would be required for this complex. Ten additional practices are described which, when used, will reduce operating costs even further. A continuing study with more precise data on the production requirements for the service plants in the complex will yield a more balanced and realistic system.

For the past 20 years, the National Foundation for Agricultural Research in Crete and the School of Agricultural Technology of the Technological and Educational Institute of Crete have been involved in a number of research and development activities, related to the production and evaluation of compost derived from a variety of local solid, mainly agricultural organic wastes. Materials such as olive press cake, olive tree leaves (OTL) and branches, vine branches (VB), pressed grape skins (PGS), pig manure (PM), sewage sludge and the organic fraction of municipal solid waste (OFMSW) have been evaluated for their behaviour during composting, their compatibility in mixtures and the quality of the end product. The quality evaluation included both a detailed physiochemical (pH, electrical conductivity (EC), nutrients concentration, heavy metal concentration, etc.) and biological analyses (pathogenic microorganisms). It also included an agronomic evaluation, in which composts were used either as a soil amendment or as a component for substrates in open air or covered (greenhouse) cultivation mainly of local vegetables (tomatoes, cucumbers, etc.). All materials were composted successfully, especially when mixed. The end products contained large amounts of organic matter, usually combined with an increased EC value. Pressed grape skins should be considered as the ideal raw material, producing a high quality compost, with the lowest EC value (1.57 mS cm−1) and the largest organic matter concentration (84.50%), compared to all other materials. When any of the produced compost was used in a ratio of 30% by volume (v/v), it increased plant growth, whereas in larger volumes, it presented phytotoxic behaviour, inhibiting both root and shoot development. Keywords: Olive wastes, Vine wastes, Pig manure, Sewage sludge, Municipal solid waste, Compost

Bioremediation has become an important method for the restoration of oil-polluted environments by the use of indigenous or selected microbial flora. Several factors such as aeration, use of inorganic nutrients or fertilizers and the type of microbial species play a major role in the remediation of oil-contaminated sites. Experiments were undertaken for bioremediation of oil sludge-contaminated soil in the presence of a bacterial consortium, inorganic nutrients, compost and a bulking agent (wheat bran). Experiments were conducted in glass troughs for the 90-day period. Bulked soil showed more rapid degradation of oil compared to all other amendments. During the experimental period, wheat bran-amended soil showed 76% hydrocarbon removal compared to 66% in the case of inorganic nutrients-amended soil. A corresponding increase in the number of bacterial populations was also noticed. Addition of the bacterial consortium in different amendments significantly enhanced the removal of oil from the petroleum sludge from different treatment units. Keywords: Bioremediation, Contaminated soil, Oil sludge, Degradation

Substantial progress has been made in the production of environmental level, natural matrix, radioactivity standards of soil of low organic and low carbonate content, and of human lung and human liver. This is in response to the deliberations of the 1977 ICRM meeting at which the need for such standards was voiced and the criteria suggested. The soil samples have been reduced to optimum particle size and are ready for blending and standardization. A ten year supply of this standard should be ready in a year or less. Reducing the dried lung and liver to less than 74 μm has proven formidable because of the natural fat and oil content. Using cyrogenic milling techniques more than three quarters of the total mass of each has been reduced to the desired particle size; the balance will either be reduced or removed and we can then proceed to the final standardization.

Toxicity characterization of chemical emissions in Life Cycle Assessment (LCA) is a complex task which usually proceeds via multimedia (fate, exposure and effect) models attached to models of dose–response relationships to assess the effects on target. Different models and approaches do exist, but all require a vast amount of data on the properties of the chemical compounds being assessed, which are hard to collect or hardly publicly available (especially for thousands of less common or newly developed chemicals), therefore hampering in practice the assessment in LCA. An example is USEtox, a consensual model for the characterization of human toxicity and freshwater ecotoxicity. This paper places itself in a line of research aiming at providing a methodology to reduce the number of input parameters necessary to run multimedia fate models, focusing in particular to the application of the USEtox toxicity model. By focusing on USEtox, in this paper two main goals are pursued: 1) performing an extensive exploratory analysis (using dimensionality reduction techniques) of the input space constituted by the substance-specific properties at the aim of detecting particular patterns in the data manifold and estimating the dimension of the subspace in which the data manifold actually lies; and 2) exploring the application of a set of linear models, based on partial least squares (PLS) regression, as well as a nonlinear model (general regression neural network — GRNN) in the seek for an automatic selection strategy of the most informative variables according to the modelled output (USEtox factor). After extensive analysis, the intrinsic dimension of the input manifold has been identified between three and four. The variables selected as most informative may vary according to the output modelled and the model used, but for the toxicity factors modelled in this paper the input variables selected as most informative are coherent with prior expectations based on scientific knowledge of toxicity factors modelling. Thus the outcomes of the analysis are promising for the future application of the approach to other portions of the model, affected by important data gaps, e.g., to the calculation of human health effect factors. Keywords: Machine learning, Life Cycle Assessment, Chemical risk assessment, USEtox, Dimensionality reduction, Nonlinear modelling

Life cycle assessment (LCA) is a popular tool used to evaluate the environmental performance of municipal solid waste (MSW) management systems. Although reviews of LCAs of MSW have been undertaken to assess the validity of the ‘waste hierarchy,’ a recent review of the goal, scope and results of LCAs of mixed-material MSW management systems has yet to be performed. This paper is a comparative analysis of 20 process-based LCAs of MSW published between 2002 and 2008 in a total of 11 English-language peer-reviewed journals. It quantifies the methodological transparency of the studies and the frequency of use of particular system boundaries, types of data sources, environmental impact categories, impact weightings, economic valuations, sensitivity analyses, and LCA computer models. Net energy use (NEU), global warming potential (GWP), and acidification potential (AP) values for various types of MSW management systems are also compared using statistical indicators.The reviewed LCAs differ substantially in their system boundaries. Half or more of the LCAs either do not mention or are unclear in whether or not life cycle emissions from energy inputs or capital equipment are included in the calculation of results. Only four impact categories are common to more than half of the reviewed LCAs. The human and ecological toxicity impact categories are much less common than global warming potential, acidification, and eutrophication.A financial life cycle costing is present in eight of the reviewed LCAs, while an economic valuation of the environmental impacts is observed in five. Explicit sensitivity analyses are present in 4/20 of the studies, although many more LCAs evaluate the effects of varying model parameters by increasing the number of waste management scenarios. There is no consensus on whether or not to use the marginal or average source of electricity in calculating environmental impacts. Eight out of the 20 do not mention this source while the remaining LCAs are evenly split between the marginal and average electricity source. One quarter of the reviewed LCAs supply weighted results for the overall environmental performance of MSW management scenarios. All but one of these concurred with the ‘hierarchy of waste’ that the environmental performance of landfilling is lower than that of all the other treatment methods, and that thermal treatments are inferior to recycling.The comparative analyses of the NEU, GWP and AP results are based on 37, 45, and 42 MSW management scenarios, respectively. As measures of statistical dispersion, the interquartile ranges of the NEU, GWP and AP values are lowest for the landfilling (AP, NEU) and thermal treatment (GWP) scenarios. The results of the statistical analysis of the NEU, AP and GWP values appear to indicate that thermal treatment scenarios have a better environmental performance than landfilling, while the results for mixed treatment scenarios are less obvious. A comparison of the relative environmental performances of MSW treatment scenario types within each study did not provide a clear confirmation or repudiation of the waste hierarchy.This paper concludes that many recently published LCAs do not ensure that the methodological assumptions are made clear to the reader. Lack of transparency makes the results difficult to interpret, and hampers meaningful comparisons between the LCA results. A convergence in the adoption of particular assumptions that are more representative of MSW management systems would facilitate the comparison of the results. Keywords: Acidification potential, Comparative analysis, Global warming potential, LCA, Life cycle assessment, Life cycle costing, Municipal solid waste, MSW, Net energy use, Scope, System boundaries, Waste hierarchy

The goal setting regime imposed by the UK safety regulator has important implications for an organisation's ability to manage health and safety related risks. Existing approaches to safety assurance based on risk analysis and formal safety assessments are increasingly considered unlikely to create the step change improvement in safety to which the offshore industry aspires and alternative approaches are being considered. One approach, which addresses the important issue of organisational behaviour and which can be applied at a very early stage of design, is the capability maturity model (CMM). The paper describes the development of a design safety capability maturity model, outlining the key processes considered necessary to safety achievement, definition of maturity levels and scoring methods. The paper discusses how CMM is related to regulatory mechanisms and risk based decision making together with the potential of CMM to environmental risk management.

This paper highlights some recent trends and developments in dialogue on radioactive waste management in the UK. In particular, it focuses on the use of dialogue around options for the management of risk, and describes techniques for stakeholder dialogue in the field of radioactive waste management. The paper summarises past and on-going experience in the UK, and provides an overview of some practical examples from decommissioning of the former reprocessing facility at Dounreay in Scotland.In common with developments and trend in other countries, the UK has moved to a position where there is now widespread recognition that radioactive waste management requires not only sound technical assessment of risk, but also public participation, consultation and stakeholder dialogue on proposed solutions and the associated risks. In fact, the shift of position has arguably been quite pronounced, with formal procedures to identify, clarify and integrate stakeholders' issues and concerns within the decision-making processes.Experience suggests that citizens are capable of engaging with complex technical issues such as radioactive waste. Indeed, the earlier in the decision-making process that public and stakeholder engagement (PSE) occurs–for example, on the consideration of options and alternatives–the greater the chance of reaching a successful outcome that properly reflects the values and opinions of stakeholders.In the UK, the assessment of alternative waste management options is increasingly being addressed through Best Practical Environmental Option (BPEO) studies. Responses to stakeholder engagement processes and experience of conducting BPEO studies emphasise that consultation must be open, transparent, deliberative and inclusive. However, while early consideration of generic approaches and option choices is necessary to generate a climate of openness and understanding, it remains essential to fully engage with local stakeholder and community groups to consider issues associated with proposed developments at a site-specific level.An interesting area where further attention may be warranted is the use in final decision-making of the results from participatory processes such as BPEO studies. Demonstrating clearly that participants' views have influenced decisions appears to be essential for retaining legitimacy and trust, confidence and goodwill. Keywords: Radioactive waste management, Best Practical Environmental Option, Public and stakeholder engagement

Risk-based regulation has become increasingly popular in recent years. Proponents argue that it facilitates robust governance, contributing to efficient and effective use of regulatory resources and delivering interventions in proportion to risk. Critics contend that the challenges of operationalising risk-based governance mitigate its potential benefits. In this paper we start by considering what we mean by risk-based governance and discuss some of the factors shaping the adoption of such strategies. We then consider the development and operation of risk-based approaches in the environmental policy domain, focusing specifically on the regulation of contaminated land and radioactive waste. We argue that whilst risk-based approaches can offer important benefits, they face a range of epistemic, institutional and normative challenges that can play an important role in shaping the way that organisations manage both risks to society and their own institutional risks. This has profound implications for achieving regulatory objectives and, for this paper, the environmental outcomes that the regulations are designed to deliver. Keywords: Risk, Risk governance, Risk-based regulation, Environmental policy, Contaminated land, Radioactive waste

The main focus of this paper is to bring out the cost effectiveness of cleaner production and the role played by cleaner production in minimizing the health hazards of pollutants in the workplace. Improvement in workplace health hazards due to implementation of cleaner production has been illustrated with the results of the study. This study was carried out in 16 Manufacturing units in two states of Maharashtra and Gujarat in India. The results clearly shows with the help of cost benefit analysis that cleaner technologies not only add to the bottom line of the company but also minimize exposure to toxic chemicals like Ammonia, phenol, carbon tetrachloride, toxic dust, etc. The main driving forces motivating the firms to go in for cleaner production are evaluated. It is found that in most of the units safety and health factors were ranked as one among the first four driving forces behind implementation of cleaner technologies. The paper ends with recommendations for the promotion of cleaner technologies. Keywords: Pollution, Cleaner technology, Cost benefit analysis, Health hazard, Occupational health

The common approach to performing quantitative risk assessments in the contaminated land industry in the UK lacks a formal methodology for the treatment of the full range of uncertainties and for documenting decisions regarding the development of conceptual models and the selection of computer codes. The approach presented here represents an alternative, more detailed, and systematic approach for developing conceptual models and addressing uncertainties when undertaking contaminated land risk assessments. It is intended that the advantages of this approach are recognised by practitioners in the contaminated land industry and adopted, where appropriate, to help improve the quality of contaminated land risk assessments. The identification of features, events, and processes (FEPs) has been applied to safety assessments of deep geological and near-surface disposal of radioactive wastes. One of the primary benefits of using this approach is in the development of conceptual models. The approach identifies the FEPs that need to be addressed during the development of conceptual models and in the selection of suitable computer codes that can be used to represent the conceptual models. This approach has been applied by BNFL at the low-level radioactive waste disposal site at Drigg in Cumbria and is currently being adopted for a contaminated land study at the Sellafield site, also in Cumbria. This paper presents the advantages of using FEPs in the development of conceptual models and the treatment of uncertainties. The paper also discusses the application of this approach to contaminated land studies and provides an example to demonstrate the application of the approach. BNFL's approach at the Drigg site involves the identification of components (features) and phenomena (events and processes) that govern interactions and dependencies between the components by arranging them in a matrix format. Keywords: FEPs, Contaminated land, Conceptual models, Low-level radioactive waste, Safety assessment

This paper gives a brief outline of some of the findings of a study of thermal preferences in housing in South and central Australian climates, where both summer and winter thermal performance need to be considered in design, and where the normal pattern of heating and cooling equipment use is intermittent. The study aimed to discover a range of design data relevant to housing in climates and situations such as these, where designers may need to make compromises in design for good thermal performance. A central question was what periods should be taken as high priority design times in designing for thermal performance. Data collection was by mail survey and by electronic devices called comfort vote loggers. The paper shows how the complexity of the thermal design problem and the need for compromises in design affect the nature of applicable data. It shows how systematic study of thermal preferences in the field can help to bridge the gap between approaches which model thermal performance of buildings and assess performance against some measure of thermal satisfaction, and approaches which recommend built solutions for various climates on the basis of interpretation of how physical science suggests that traditional buildings perform in those climates.

Despite regulatory efforts and position papers, electrical and electronic waste (e-waste) remains ill-managed as evidenced by the extremely low rates of proper e-waste recycling (e-recycling) worldwide, ongoing illegal shipments to developing countries and constantly reported human health issues and environmental pollution. The objectives of this review are, first, to expose the complexity of e-waste problems, and then to suggest possible upstream and downstream solutions. Exploring e-waste issues is akin to opening a Pandora's box. Thus, a review of prevailing e-waste management practices reveals complex and often intertwined gaps, issues and challenges. These include the absence of any consistent definition of e-waste to date, a prevalent toxic potential still involving already banned or restricted hazardous components such as heavy metals and persistent and bioaccumulative organic compounds, a relentless growth in e-waste volume fueled by planned obsolescence and unsustainable consumption, problematic e-recycling processes, a fragile formal e-recycling sector, sustained and more harmful informal e-recycling practices, and more convoluted and unpredictable patterns of illegal e-waste trade. A close examination of the e-waste legacy contamination reveals critical human health concerns, including significant occupational exposure during both formal and informal e-recycling, and persistent environmental contamination, particularly in some developing countries. However, newly detected e-waste contaminants as well as unexpected sources and environmental fates of contaminants are among the emerging issues that raise concerns. Moreover, scientific knowledge gaps remain regarding the complexity and magnitude of the e-waste legacy contamination, specifically, a comprehensive characterization of e-waste contaminants, information on the scale of legacy contamination in developing countries and on the potential environmental damage in developed countries, and a stronger body of evidence of adverse health effects specifically ascribed to e-waste contaminants. However, the knowledge accumulated to date is sufficient to raise awareness and concern among all stakeholders. Potential solutions to curb e-waste issues should be addressed comprehensively, by focusing on two fronts: upstream and downstream. Potential upstream solutions should focus on more rational and eco-oriented consumer habits in order to decrease e-waste quantities while fostering ethical and sustained commitments from manufacturers, which include a limited usage of hazardous compounds and an optimal increase in e-waste recyclability. At the downstream level, solutions should include suitable and pragmatic actions to progressively reduce the illegal e-waste trade particularly through international cooperation and coordination, better enforcement of domestic laws, and monitoring in both exporting and receiving countries, along with the supervised integration of the informal sector into the recycling system of developing countries and global expansion of formal e-waste collection and recycling activities. Downstream solutions should also introduce stronger reverse logistics, together with upgraded, more affordable, and eco-friendly and worker-friendly e-recycling technologies to ensure that benefits are derived fully and safely from the great economic potential of e-waste. Keywords: E-waste management, Chemical contaminants, Electronic recycling, Legacy contamination, Human health, Occupational health

This paper describes measurements and computational modelling carried out in the MOBI-Kids case-control study to assess the extremely low frequency (ELF) exposure of the brain from use of mobile and cordless phones. Four different communication systems were investigated: Global System for Mobile (GSM), Universal Mobile Telecommunications System (UMTS), Digital Enhanced Cordless Telecommunications (DECT) and Wi-Fi Voice over Internet Protocol (VoIP). The magnetic fields produced by the phones during transmission were measured under controlled laboratory conditions, and an equivalent loop was fitted to the data to produce three-dimensional extrapolations of the field. Computational modelling was then used to calculate the induced current density and electric field strength in the brain resulting from exposure to these magnetic fields. Human voxel phantoms of four different ages were used: 8, 11, 14 and adult. The results indicate that the current densities induced in the brain during DECT calls are likely to be an order of magnitude lower than those generated during GSM calls but over twice that during UMTS calls. The average current density during Wi-Fi VoIP calls was found to be lower than for UMTS by 30%, but the variability across the samples investigated was high. Spectral contributions were important to consider in relation to current density, particularly for DECT phones. This study suggests that the spatial distribution of the ELF induced current densities in brain tissues is determined by the physical characteristics of the phone (in particular battery position) while the amplitude is mainly dependent on communication system, thus providing a feasible basis for assessing ELF exposure in the epidemiological study. The number of phantoms was not large enough to provide definitive evidence of an increase of induced current density with age, but the data that are available suggest that, if present, the effect is likely to be very small. Keywords: EMF, ELF, Mobile phones, Induced current density, Magnetic fields, Epidemiology

Considerable efforts have been invested so far to evaluate and rank the quality and relevance of (eco)toxicity data for their use in regulatory risk assessment to assess chemical hazards. Many frameworks have been developed to improve robustness and transparency in the evaluation of reliability and relevance of individual tests, but these frameworks typically focus on either environmental risk assessment (ERA) or human health risk assessment (HHRA), and there is little cross talk between them. There is a need to develop a common approach that would support a more consistent, transparent and robust evaluation and weighting of the evidence across ERA and HHRA. This paper explores the applicability of existing Data Quality Assessment (DQA) frameworks for integrating environmental toxicity hazard data into human health assessments and vice versa. We performed a comparative analysis of the strengths and weaknesses of eleven frameworks for evaluating reliability and/or relevance of toxicity and ecotoxicity hazard data. We found that a frequent shortcoming is the lack of a clear separation between reliability and relevance criteria. A further gaps and needs analysis revealed that none of the reviewed frameworks satisfy the needs of a common eco-human DQA system. Based on our analysis, some key characteristics, perspectives and recommendations are identified and discussed for building a common DQA system as part of a future integrated eco-human decision-making framework. This work lays the basis for developing a common DQA system to support the further development and promotion of Integrated Risk Assessment. Keywords: Reliability, Relevance, Data evaluation, Quality assessment, Integrated hazard assessment, Integrated risk assessment

Cities are complex adaptive systems whose responses to policy initiatives emerge from feedback interactions between their parts. Urban policy makers must routinely deal with both detail and dynamic complexity, coupled with high levels of diversity, uncertainty and contingency. In such circumstances, it is difficult to generate reliable predictions of health-policy outcomes. In this paper we explore the potential for low-order system dynamics (LOSD) models to make a contribution towards meeting this challenge. By definition, LOSD models have few state variables (≤5), illustrate the non-linear effects caused by feedback and accumulation, and focus on endogenous dynamics generated within well-defined boundaries. We suggest that experience with LOSD models can help practitioners to develop an understanding of basic principles of system dynamics, giving them the ability to ‘see with new eyes’. Because efforts to build a set of LOSD models can help a transdisciplinary group to develop a shared, coherent view of the problems that they seek to tackle, such models can also become the foundations of ‘powerful ideas’. Powerful ideas are conceptual metaphors that provide the members of a policy-making group with the a priori shared context required for effective communication, the co-production of knowledge, and the collaborative development of effective public health policies. Keywords: Wicked problems, Transdisciplinary communication, Low-order models, Conceptual metaphor, Powerful ideas, Urban health policy

There is increasing evidence to suggest that the use of subjective responses to questions concerning night-time environmental noise exposure is a robust method of assessing sleep disturbance from road traffic noise. However, there have only been a few studies exploring this issue in a real world context beyond controlled laboratory settings. This paper presents results from such a study. It utilises 208 household questionnaire surveys to assess subjective responses to levels of night-time sleep disturbance and annoyance from four different residential sites. Each residential site is characterised by a dominant noise source – road, light rail, and aircraft – and these sites are compared to a control site that is relatively free from transportation noise. The results demonstrate the inadequacy of continuous equivalent noise level measures as indicators of night-time disturbance. Furthermore, they suggest that the use of these measures alone is likely to result in inaccurate appraisals of night-time sleep disturbance from transportation noise. Ultimately, the research implies that measurement data should be used in conjunction with subjective response data to accurately gauge the level of night-time disturbance from transportation noise.

Hydraulic fracturing (fracking) has been used extensively in the US and Canada since the 1950s and offers the potential for significant new sources of oil and gas supply. Numerous other countries around the world (including the UK, Germany, China, South Africa, Australia and Argentina) are now giving serious consideration to sanctioning the technique to provide additional security over the future supply of domestic energy. However, relatively high population densities in many countries and the potential negative environmental impacts that may be associated with fracking operations has stimulated controversy and significant public debate regarding if and where fracking should be permitted. Road traffic generated by fracking operations is one possible source of environmental impact whose significance has, until now, been largely neglected in the available literature. This paper therefore presents a scoping-level environmental assessment for individual and groups of fracking sites using a newly-created Traffic Impacts Model (TIM). The model produces estimates of the traffic-related impacts of fracking on greenhouse gas emissions, local air quality emissions, noise and road pavement wear, using a range of hypothetical fracking scenarios to quantify changes in impacts against baseline levels.Results suggest that the local impacts of a single well pad may be short duration but large magnitude. That is, whilst single digit percentile increases in emissions of CO2, NOx and PM are estimated for the period from start of construction to pad completion (potentially several months or years), excess emissions of NOx on individual days of peak activity can reach 30% over baseline. Likewise, excess noise emissions appear negligible (

The paper discusses the trend in all the U.S. industries toward increased water recycling and reuse. Also presented are the water use demands by various industries, and the water use by functions. Data are given on industrial water quality in use for various functions among selected high water using industries. Presented is an over-all system designed for a closed-loop cycle for industrial wastewater. This will be practical for industry to implement by 1985 or soon thereafter if the required technology is properly developed. Research and development needs to achieve this closed-loop system are identified. Rather than a discussion of economics with typical costs based on amount of water treated or on the specific processes employed, the paper presents data on the total cost of removal of controlling factors from a hypothetical wastewater. Future demands and restrictions on industrial wastewater are stated and ten references are cited.

The theory of competing risks is concerned with assessing a specific risk in the complicating presence of other risks. This paper reviews existing methods for dealing with the problem. Much of the existing methodology (both parametric and nonparametric) involves the assumption of independent risks. This situation receives most of the attention in this paper, although a brief discussion summarizing attempts to deal with the complicated problem of dependent risks is given. Adaptations of methods used to incorporate concomitant information in survival analyses are discussed. Brief reference is made to the most relevant graphical methods that have been proposed. The review tends to be verbal in nature, leaving the interested reader to check out mathematical details in the references.

Control of particulate emissions from pulverized coal fired steam generators is becoming a significant factor in the siting and public acceptability of large coal burning power plants. The particulate emission limit established by the EPA for new coal fired boilers is 0.03 lb/10 6 Btu (13 ng/J) Possibly more restrictive than this is the state of New Mexico's particulate regulation which calls for no more than 0.05 lb/10 6 Btu (22 ng/J) total, and no more than 0.02 lb/10 6 Btu (9 ng/J) less than 2 microns in diameter. This paper will evaluate the effect of these stringent limitations on the technical feasibility and economics of dry particulate removal. Electrostatic precipitators have been the dominant particulate collection device in the electric utility industry for many years because of their low capital and operating cost. However, increasingly stringent emission standards have led to substantially higher costs for precipitators. These costs have increased sufficiently for fabric filtration to become a competitive alternative in achieving cost effective control. This paper will compare the economics and performance of fabric filtration with respect to conventional electrostatic precipitators. The paper will also address the preliminary evaluation procedures that should be followed in order to select the appropriate device for new or existing coal-fired boilers.

The air quality impacts of hazardous waste disposal sites can be assessed on the basis of their contribution to each of the toxic contaminants. The purpose of this paper is to discuss the available methods of air quality assessment and their drawbacks. The need of air quality assessment is to assure that ambient concentrations of specific contaminants resulting from emissions will not exceed the acceptable levels for protection of public health and the ecosystem. Ambient concentrations of toxic contaminants are generally obtained by field measurements or air monitoring. However, field measurements and air monitoring of low-level toxic contaminants are costly and time consuming. As a result, most hazardous waste land disposal sites have not been adequately assessed. This paper describes current regulatory requirements in the United States for air quality assessment of hazardous waste land disposal sites. Emphasis is directed toward air quality assessment methodology. The paper also discusses emission predicting models based on the waste quantity and composition, scientific analysis of the waste conversion process together with meteorological conditions. The emission models are especially useful where emission cannot be reliably monitored or where a new disposal site is proposed.

In October 1977, Southwestern Public Service Company executed a contract with the U.S. Environmental Protection Agency that called for a study to assess the performance of a fabric filter system installed on a large utility boiler that utilizes low sulfur Western coal. The project is now into its second year and the objectives of this paper are to describe the scope and intent of the study, as well as to report progress to date. In addition, some of the difficulties that we have encountered are discussed. Although some of these problems have resulted in procedural changes, the intent of the study has not been altered. This paper describes work being done in specific areas with which both the EPA and Southwestern are connected. These include fabric assessment, data collection, selection and installation of instrumentation, and overall fabric filter system performance. Results of the first performance test are also reviewed and the installation of a pilot baghouse is discussed.

A risk assessment strategy considering the impact of chemicals on the whole ecosystem has been developed in order to create a sound and useful method for quantifying and comparing the global risk posed by the main different hazardous chemicals found in the environment. This index, called Environmental Risk Index for Chemical Assessment (ERICA), merges in a single number the environmental assessment, the human health risk assessment and the uncertainty due to missing or uncertain data. ERICA uses a dedicated scoring system with parameters for the main characteristics of the pollutants. The main advantage is that it preserves a simple approach by condensing in this single value an analysis of the risk for the area under observation.ERICA quantifies and compares the global risk posed by hazardous chemicals found in the environment and can be considered a diagnostic and prognostic method for environmental contaminants in critical and potentially dangerous sites, such as incinerators, landfills and industrial areas or in broader geographical areas. The application of the proposed integrated index provides a preliminary quantitative analysis of possible environmental alert due to the presence of one or some pollutants in the investigated site.This paper presents the method and the equations behind the index and a first case study based on the Italian legislation and a pilot study located on the Italian seacoast. Keywords: Risk index, Pollutants, Ecotoxicity, Human risk assessment, Environment, Integrated strategy

Active pharmaceutical ingredients (APIs) from medications can enter the environment as trace contaminants, at individual concentrations generally below a part per billion (μg/L). APIs enter the environment primarily via the discharge of raw and treated sewage. Residues of unmetabolized APIs from parenteral and enteral drugs are excreted in feces and urine, and topically applied medications are washed from skin during bathing. These trace residues may pose risks for aquatic life and cause concern with regard to subsequent human exposure.APIs also enter the environment from the disposal of unwanted medications directly to sewers and trash. The relative significance of this route compared with excretion and bathing is poorly understood and has been subject to much speculation. Two major aspects of uncertainty exist: the percentage of any particular API in the environment originating from disposal is unknown, and disposal undoubtedly occurs from a variety of dispersed sources. Sources of disposal, along with the types and quantities of APIs resulting from each source, are important to understand so that effective pollution prevention approaches can be designed and implemented.Accumulation of leftover, unwanted drugs poses three major concerns: (i) APIs disposed to sewage or trash compose a diverse source of potential chemical stressors in the environment. (ii) Accumulated drugs represent increased potential for drug diversion, with its attendant risks of unintentional poisonings and abuse. (iii) Leftover drugs represent wasted healthcare resources and lost opportunities for medical treatment.This paper has four major purposes: (1) Define the processes, actions, and behaviors that control and drive the consumption, accumulation, and need for disposal of pharmaceuticals. (2) Provide an overview of the diverse locations where drugs are used and accumulate. (3) Present a summary of the first cataloging of APIs disposed by a defined subpopulation. (4) Identify opportunities for pollution prevention and source reduction. Keywords: Pharmaceuticals, Medications, APIs, Accumulation, Disposal, Environmental pollution, Pollution prevention

The increasing demand of the growing population requires enhancement in the production of rice. This has a direct bearing on the global environment since the rice cultivation is one of the major contributors to the methane emissions. As the rice cultivation is intensified with the current practices and technologies, the methane fluxes from paddy fields will substantially rise. Improved high yielding rice varieties together with efficient cultivation techniques will certainly contribute to the curtailment of the methane emission fluxes. In this paper, the system dynamic approach is used for estimating the methane emissions from rice fields in India till the year 2020. Mitigation options studied for curtailing the methane emissions include rice production management, use of low methane emitting varieties of rice, water management and fertilizer amendment. The model is validated quantitatively and sensitivity tests are carried out to examine the robustness of the model. Keywords: Global warming, Greenhouse gases, Methane emission, Mitigation options, Rice fields, System dynamics

Few would now deny that the use of organobromine compounds to achieve fire retardancy in a diverse array of products and materials has led to contamination of the ecosphere on a widespread scale. This environmental prevalence and persistence of the brominated flame retardants, coupled with growing evidence of their potential for harm, present all too familiar parallels with the previous generation of persistent organic pollutants. Indeed, given the intrinsic properties of these brominated chemicals, the nature and extent of the current problem could well have been predicted in advance. The question is then whether we are prepared to let history repeat itself once more or to take precautionary action now to switch to more sustainable alternatives. The choice facing society is not between brominated flame retardants and unsafe products, but between fire safety leading to global contamination or fire safety achieved in less polluting ways. If we look beyond options for simple chemical-for-chemical substitution to alternative materials and designs, many of the solutions are already available. The remainder could undoubtedly be developed given the incentives to do so. However, a strong and clear policy approach, backed by legislative phase-outs within specified (and challenging) timeframes, will be necessary to break our current dependency on organobromine chemistry. This paper presents the justification for such an approach, reviews those initiatives already underway to replace brominated flame retardants and identifies pathways to the use of more sustainable products in the service of society. Keywords: Brominated flame retardants, Organic pollutants, Fire safety

This paper presents a GA-based compromise programming technique for assessing the relocation strategy of air quality monitoring network in urban region with respect to the multi-objective and multi-pollutant design criteria. While the impact of conservative, quasi-stable, and reactive pollutants are considered in the design principles via a simulation analysis, cost, effectiveness, and efficiency characteristics are postulated in the optimization process. Therefore, technical coverage for illustrating the needs of siting air quality monitoring stations (AQMS) includes both the air quality simulation and optimization modeling analyses in a two-stage analytical framework simultaneously. It starts from determining the spatial interrelationship among those candidate sites using various types of air quality simulation models as an integrated means. And the outputs drawn from the simulation models can then be used as the required inputs in the compromise programming model in order to screen all those siting alternatives that may satisfy the planning goals subject to the essential constraints throughout the multi-objective optimization process. For the illustrating purposes, a series of technical settings for finding the optimal relocation scenarios of AQMS were examined in the case study for the city of Kaohsiung in South Taiwan where the long-term violations of official standards of ozone and particulates turn out to be critical. It not only expresses the ideas of relocation strategy but also indicates how to utilize those alternatives in the decision-making process for improving the functionality of air quality monitoring in the urban environment. Experience gained in this study clearly indicates that the more the number of pollutants and objectives considered simultaneously, the higher the number of candidate sites to be selected in the relocation strategy. Keywords: Air quality management, Monitoring, Location theory, Simulation, Optimization, Environmental systems analysis

The Jahra Plant was commissioned in 1981 as a secondary treatment plant employing the extended aeration process. The plant has been upgraded since that time by constructing additional tertiary filtration units to improve effluent quality. The plant has a design capacity of 66 000 m 3 /d. At present, the daily inflow to the plant is about 47 000 m 3 /d of domestic sewage. The sludge produced at the Jahra Plant can be classified as excess activated sludge which combines the primary and secondary solids. At present, there are 30 drying beds receiving about 100 m 3 of sludge dally. Sewage-sludge production represents about 0.5% of the total flow treated at the plant and is increasing yearly with increases in population and water consumption. Present dewatering systems are not adequate to cope with expansion in sewage treatment. Increasing the capacity of the existing plant would require more drying beds that could exacerbate existing odor problems. Some dewatering systems, such as the belt filter press and the centrifuge, have been tested to determine the most effective one under local conditions. Appropriate polymer doses for thickening have been determined. This paper describes present sludge dewatering units and operating techniques which have been developed during the operation of this facility.

The Building Research Establishment recently purchased a house in Devon, UK, which was chosen as being typical of UK construction with a suspended timber floor, and for having high radon levels, averaging 1.6 kBqm −3 and peaking above 6 kBqm −3 . This house is being used as a test facility for investigating a host of radon related issues and contains continuous radon monitoring equipment and a network of probes and sensors monitoring various environmental parameters, including temperature, relative humidity, wind data, atmospheric pressure, and a number of pressure differences. Initial results show an extreme variation in radon levels with time, challenging the direct use of short-term monitoring. For this property, forced underfloor extract ventilation is demonstrated as a reliable remedy, more effective than natural underfloor ventilation, whole house pressurization and underfloor supply ventilation. This paper describes the experimental set up and presents some preliminary radon results from the first year of operation.

This paper discusses studies of the sub-slab depressurization performance of radon mitigation systems in four schools after floor replacement, and in one newly built school, in Cornwall, England. Sub-slab pressure-field extension was assessed by means of small bore plastic tubing laid below slab-on-grade concrete floors with ‘standard’ U.K. type radon sump (sub-slab depressurization) systems. A variety of hardcore types and floor constructions were used. Improvements over the pressure-field obtained in normal U.K. floor construction were readily achieved by careful selection of hardcore free from fine material and by avoidance of sand blinding directly on the hardcore. However, the performance achieved in a similar American study was not consistently reproduced. Even with close supervision of labour and correct construction, optimum pressure-field extension was not consistently achieved. The thickness of the permeable layer and the method of laying blinding materials may be critical to success. A polyethylene membrane can keep blinding materials out of the permeable layer and may allow the usual sand blinding to be used. Careful floor construction and selection of hardcore materials could result in new-build properties requiring fewer radon sumps and/or a reduction in fan power consumption. However, this must be balanced against the increased construction costs and current inconsistency in results.

Risk estimates of fatal cancer constitute the principal component of the health detriment after low doses of ionizing radiation protection recommendations by ICRP and NCRP are based upon them. These risks are presently derived from the Life Span Study of the A bomb survivors in Japan and have recently been supported by a number of relatively imprecise studies of occupational exposure of workers in the U.K., in the U.S., and in Russia. Further verification by more precise studies would be most useful. The most promising future study is that of workers in the U.S. nuclear industry, a study which was proposed some years ago (by New York University) and endorsed by a special committee of the National Academy of Sciences, the National Research Council. The study has not yet been undertaken despite its intrinsic capability to yield more precise results than all other worker studies. This paper describes the present status of background risk estimation for radiation protection and urges that the study of workers in the U.S. nuclear power industry be undertaken without further delay.

Radium usage in the United States peaked in the late 1930's and early 1940's, much of it centered in New York, in both medical applications for cancer therapy and industrial applications mainly for self-luminous paints and static elimination. While the production of radium shifted from American to Europe after 1920, the importation of radium salts and their incorporation into products peaked during the World War II years and continued by some U.S. firms into the 1970's. New York State Department of Labor (NYS DOL), Division of Industrial Hygiene, investigated radium facilities in the 1940's to evaluate radium hazards and make recommendations for worker protection, but these were not always followed by industry. In December 1955, Industrial Code Rule 38 was promulgated which set limits for external doses and air concentrations and required That all radiation facilities be registered with the Departent. Many firms, with operations dating back to the 1930's, had major difficulties in revamping their operations to achieve compliance with these new standards. This paper will review NYS DOL investigations and enforcement activities toward Code compliance of three major radium corporations which were engaged in radium refining, reclamation, source manufacture, and radium dial painting. The summary includes review of worker dosimetry, external exposures, and air concentration data compiled from reports of on-site inspections and will briefly review several involving alleged radiation injury.

This paper describes the characterization of some atmospheric dusts collected in Chengdu and Dukou of Sichuan Province, China, and compares them with samples from Tokyo and its vicinity. The samples were fractionated with heavy liquids, followed by ordinary x-ray diffraction and fluorescence analyses. Individual particles were further analyzed using an x-ray microdiffractometer with a position sensitive proportional counter. Dukou's dust fall was characterized by high-temperature products and by large amounts of magnetite (Fe 3 O 4 ) and hematite (Fe 2 O 3 ). Chengdu's sample was characterisized by large contents of gypsum (CaSO 4 ·2H 2 O) and the lightest fraction of 3 including carbonaceous substance and some epsomite (MgSO 4 ·7H 2 O). It resembled the sample of Chiba (Japan) in the amounts of gypsum and epsomite, and it was similar to the samples to Tokyo in the large proportion of the 3 fraction. In addition to quartz and iron oxides, kaolin mineral and mica were detected in Chengdu, while plagioclase, chlorite, mica, and sodium chloride were detected in Japan. The origins of the pollutants are discussed.

The components of an environmental decision support system (EDSS) were outlined in Part 1 of this paper. Here, an example application is given using a range of data from the database in order to assess the utility of one specific model chosen from the modelbase: the one-dimensional thermal stratification model, EDD1. The model is applied to a range of lake types worldwide.

This paper reviews recent developments in the field of noise research. In our society the sources of noise pollution are increasing, as is annoyance. In research, specific attention has been paid to noise originating from motor vehicles and other surface transport, and also from aircraft, especially military aircraft and helicopters. As yet, the issue of the existence of one universal, single, dose-response relationship has remained unsolved, although some new nuances have been added. Changes in annoyance resulting from changes in noise levels are unlikely to be predicted from dose-response relationships established in “steady state” situations. Some progress has been made in developing models to predict noise annoyance from a combination of sources. It will be necessary to develop and test a theoretical framework for annoyance and its correlations, and to explore the relationship between annoyance and stress theories.

The essence of the societal problem which justifies the expenditure of large sums on studies of pollution and health is illustrated by three figures included in this paper. The first two of these figures illustrate the contemporary publicity favoring the two competing energy-producing technologies, the nuclear and the conventional fossil-burning technologies. The very existence of this costly publicity demonstrates that the decisions affecting public health are now frequently made without due regard to the relevant scientific findings. The third figure illustrates the most laudable effort of the Environmental Protection Agency to establish a relationship between hoped-for decreases in mortality and the dollar cost of removing from the environment any one of the several investigated pollutants, e.g., “particulates”, krypton-85, tritium, etc. The subsequent parts of this presentation tend to document the fact that the reliability of the EPA chart published in 1973 is illusory. The same applies to the large number of other official publications, including those of the National Academy of Sciences. The results of more modern studies brought to the fore a variety of biological chance mechanisms, such as competing risks, dose-rate effects, synergisms, etc., which make the problem attacked by EPA much more difficult than was originally anticipated. The basic research, combining the laboratory experimentation on animals and theoretical considerations, results in a better understanding of a variety of phenomena. However, this better understanding seems to imply that the solution of the practical societal problem requires a large multipollutant and multilocality epidemiological study.

Welding is an important and constantly evolving technology enjoying a higher growth rate in the metalworking industries than the general industrial growth. Welding as with most industrial processes does have its inherent problems. One of the problems is the fumes and gases generated during the welding process. This paper presents a complete technical analysis of the problems associated with most of the more common types of industrial welding. In addition, alternative engineered solutions are investigated in detail which includes a descriptive analysis of several types of air cleaning devices. Finally, the control of the welding fume problem is analyzed based on actual test installations demonstrating the ability to achieve acceptable particulate and gas concentrations levels in the worker's environment, while achieving significant heat recovery (or conditioned air) by a unique approach to air recirculation.

This paper describes a series of tests carried out with a comprehensive transportation, land use and air quality simulation system, which has been designed for planning application at the metropolitan or regional scale, within the framework of the U.S. Government's Clean Air legislation. The urban location portion of the system was developed at the University of Pennsylvania under the direction of S. H. Putman. The air quality sections incorporate models formulated in earlier studies. The system was tested with data from the San Francisco Bay area, for the period 1975–1980. The test policies included changes in regional transportation costs and population totals; local interventions in the transportation network; and controls on pollutant emissions from mobile and stationary sources. To assess net impacts, the outcomes predicted for each policy were compared with the outcomes predicted in a “benchmark”, or base run of the system. The tests showed that the system is sensitive to a broad range of air quality policies, and that it is capable of predicting important air quality consequences of transportation and land use policies. Some further development will be needed before the system can be used in practical planning situations, but there is little doubt as to the soundness of its central theoretical constructs and logical structure.

In vitro mutagenicity and carcinogenicity testing techniques are currently being used to assess the potential risk to man of exposure to diesel exhaust emissions. This paper examines general considerations of such systems, the types of in vitro tests currently available, the advantages and disadvantages of each cell line and type of test, the limitations of in vitro techniques, the alternative human cell lines that could be utilized for diesel health effects studies, and recommendations for future research employing in vitro methods.

Recent developments in wastewater treatment are resulting in the production of substantial amounts of chemically [Ca(OH)2 and Al2(SO4)3·H2O] treated sludges in need of further treatment before disposal. Although a seemingly suitable method, an unfavorable pH and low volatile solids content constitute serious problems for composting. Hence, an investigation was made of the feasibility of window composting Ca(OH)2 (lime) precipitated sludge (approximately 25% solids) when mixed with a bulking agent. Bulking agents tried were the paper fraction of municipal refuse and chipped tree and shrub trimmings. Both bulking agents were tried in their raw and in their composted states. Initial mixing was by way of a specially designed hammermill, and subsequent mixing was done manually. Compostability was measured by rate and extent of the temperature rise and fall and by destruction of volatile solids. According to the results, lime exerted no inhibitory influence on the composting process. However, the high ratio of biologically inert material to volatile solids resulted in a shortage of nutrients for the bacteria. Consequently, temperatures attained were neither sufficiently high nor of long enough duration to ensure the pathogen destruction required for public health safety.

In the past, the safety of technology has mainly been ensured by deterministic criteria that were based on engineering principles and on experience. Recently, however, it has become necessary to include risk assessment into safety policy. This need arises due to the order of magnitude of possible health and environmental impact from normal operation or accidents, as well as the complexity of modern systems that no longer allow for intuitive understanding of possible accident sequences. Assessment of risks of technical installations is subject to large uncertainties that are caused by lack of data and inadequate quantification and evaluation methods. This paper reviews the main areas of uncertainties with regard to their importance for decisionmaking. Uncertainties are an inherent part of any risk assessment result and can never be avoided. It is thus important to pay particular attention to them including limitations of methods, sensitivity to assumptions about parameters, and site-specific considerations. All this information must be described in great detail so that it can be integrated into the decisionmaking process. If applied in this context, risk assessment is a useful tool for identifying major contributors to risk and effective actions of risk management.

Fabric filtration systems have been employed in industry for over a century with relatively few technological modifications. However, with the recent substantial increase in energy costs, conservation in energy consumption has become vitally important. As a result, the filtration systems of yesteryear may not be the best approach for future applications. Recently, an external electrical field was considered in fabric filtration of industrial dust with very promising initial results. An increase in the collection efficiency, particularly for fine particulates, and a decrease in the pressure drop was observed. In this paper the further results of an experimental program in the investigation of pressure drop in the electrostatic fabric filtration in industrial dust control are presented. The basic apparatus, a bench-scale electrostatic fabric filtration system, creates a representative dust cake under specific conditions of operating parameters and charge levels. The results clearly indicate that filter and dust cake resistance, or pressure drop, decreases substantially with the increased electrostatic field strength for all industrial dust samples tested, regardless of fabric type and other relevant parameters.

This paper contains detailed data on atmospheric emissions from power plants with a capacity of more than 25 MW electric in the United States. The data are gathered from utility files as presented to the U.S. Environmental Protection Agency. Pollutants covered are CO, NOx, SOx3, particulates, and total hydrocarbons. The data indicate that in 1977 about 420×109 kg coal, 84×106 m3 oil, and 65×106 m3 of natural gas were used to generate electricity. Pollutants generated were 2×109kg particulates, 17×109 kg SO2, 6×109 kg NOx, 78×106 kg hydrocarbons and 0.3×106 kg of CO.

This paper summarizes the data made available during the last decade on the subject of emission levels of wastewaters and solid residuals from the petroleum refininf industry. The data for both traditional and priority pollutants from a number of studies are considered. Specific organic compounds which are not traditional pollutants and are not on the priority pollutant list are presented for some cases. A discussion of accuracy, precision, variance, and some causes of variance is presented. Types of wastewater and residual samples for which data are presented include raw waste loadings from Class A through E refineries, loadings of various pollutants across several process units such as dissolved air flotation, activated sludge processes, carbon columns (powdered and granular), and clarifiers, and oily solids (tank bottoms, crude oil, bunker C, and waxy product).

A carborundum fabric filter was retrofitted to the Cameo No. 1 unit in 1978. Cameo Station, owned and operated by Public Service Company of Colorado, is near Grand Junction, Colorado, and No. 1 unit (22 MW) was first placed in service in 1958. The purchase contract for the fabric filter was written on July 2, 1976, but due to problems in obtaining an emission permit from the state of Colorado, actual construction did not begin until February, 1978. The fabric filter, designed with 1.92 gross air-to-cloth ratio and reverse air, was placed in service December 18, 1978. This paper covers the design aspects, construction features, startup procedures, and acceptance testing.

Energy and environment are complementary goals of industrial society. The OECD COMPASS project recognises the need for comprehensive information and assessment of the environmental implications of energy strategies and systems, not just energy sources, for effective policymaking in both energy and environmental fields. Energy systems are viewed from the end-use perspective in comparing the environmental effects of different trends and strategies in energy use. This paper discusses methodological criteria for effective assesstment in the environmental field, and some applications to the environmental implications of energy use in space heating and cooling, involving three case studies in different OECD countries. Some conclusions are drawn concerning energy-environment policy, in particular concerning the role of comparative assessment techniques in policymaking.

Microbiological Safety Cabinets are designed to provide protection to an operator from aerosol hazards that may be generated when handling infectious material. In addition, some types of cabinet can provide protection to the work being handled. Several national standards have been published in recent years which define the construction and performance of these devices; the three types of safety cabinet designated Classes I, II, and III are defined and described in this paper. A measured degree of operator protection is required at the front aperture of Class I and II cabinets, and a new method for assessing operator protection factor based upon a challenge aerosol of potassium iodide is described. Cabinet performance is discussed in relation to containment test results using this system. Working procedures and unsuitable environments can prejudice the containment performance of open-fronted cabinets by several orders of magnitude, and various aspects of this problem are discussed and illustrated. The importance of on-site commissioning tests to ensure adequate operator protection is emphasised. The application of safety cabinet testing techniques has been extended to assess the performance of fume cupboards (hoods), complete laboratories, and special “hybrid” installations such as may be used for handling carcinogenic or radiopharmaceutical material.

Dust build-up on adjacent surfaces is often an unwanted effect in industrial processes handling pulverized materials. In the case of electrostatic precipitation, build-up of dust on the collecting surface is the purpose of the process. Removal of this build-up is sometimes difficult, but necessary to maintain the continuity of the process. Dry-process methods for dust removal include rapping by impact. It is the intent of this paper to provide information on the general subject of dust removal from plates, on rapping systems used in electrostatic precipitators, and on measurements and order of magnitude of rapping forces. Rapping acceleration test results obtained in the laboratory are expanded to cover full-scale collecting surface plates. Effects of plate design, plate height and length, method of support, rapping, hammer weight, and lift are analyzed.

An analysis of the forces that produce emissions from unpaved roads shows that if fine material can be reduced or moisture increased, emissions will be reduced. Instead of collecting emissions, this new approach would decrease the emissions by reducing the fine material or by making minor increases in the moisture content of the road. In either case, a stable, rot-resistant, water-permeable fabric would be used to separate road ballast from the subsoil. Preliminary evaluation and economic analysis indicate that roads constructed in this way can be cheaper than conventional unpaved roads when subsoil load-bearing characteristics are poor. The paper describes the theoretical analysis, preliminary results, and economics of the idea.