Search

This paper evaluates the environmental impacts of different alternatives for handling of sludge from paper and pulp mills in Sweden, using Life Cycle Assessment (LCA). The common practice of incineration of biosludge with energy recovery followed by landfilling of ash (System A) was compared with the alternative of digesting sludge anaerobically to produce biogas using different digestate residue management options. The digestate produced from anaerobic digestion (AD) was assumed to be incinerated for heat energy recovery in System B or pyrolyzed for biochar production in System C to be mixed with forest soils. The impact categories considered in this work are climate change, non-renewable energy use, mineral extraction, aquatic ecotoxicity, carcinogens and non-carcinogens. The LCA results demonstrate that the two proposed systems significantly reduce the environmental impacts of biosludge management relative to incineration. An 85% reduction in the aquatic ecotoxicity impact is achieved in System C, due to the reduced mobility of heavy metals in biochar relative to ash. System C, on the whole, outperformed the other two, leading the authors to the recommendation that the use of pulp and paper mill biosludge in biogas-biochar production systems is preferable to merely recovering energy from it.

A kind of wood pulp fiber paper (WPFP) was proposed as candidate for the matrix of desiccant wheel. Silica gel was coated on WPFP by impregnation method and the corresponding coating ratio was obtained and analyzed. Then the thermal conductivity, pore structure and adsorption/desorption performances of WPFP coated with silica gel were tested and analyzed. The results indicated that the WPFP has high coating ratio for silica gel due to its hydrophilic characteristic. The thermal conductivity of WPFP coated with silica gel after the first coating increases obviously compared with raw WPFP and reaches to 0.1292 W/(m⋅K). In addition, the WPFP coated with silica gel after the first coating has high specific surface area and its maximal adsorption quantity for water vapor can be 0.240 g/g. Finally, the DCOP of the desiccant wheel using WPFP as matrix obtained by numerical simulation can be 1.75 under the given working condition that the temperature of regeneration air is set as 90 °C and the inlet condition of process air is set as 34.3 °C and 56.2% RH. It is indicated that the desiccant wheel using WPFP as matrix can meet the requirement of air dehumidification and save energy by 7.35% simultaneously.

The paper drying process has the highest level of energy consumption in the pulp and paper production process. Analysis and optimization of the energy system during the paper drying process is critical for improving the energy efficiency of the entire paper mill. In the existing model for the paper drying process, the solution requires accurate boundary conditions such as the air temperature and humidity of the pocket area and the cylinder surface temperature, which are very difficult to obtain in the papermaking process. This can result in significant deviations between the model solution and the actual production process. This paper focuses on the single-tier dryer cylinder-based paper drying process that has been widely used with high-speed papermaking machines in recent years. A mathematical model is proposed based on real-time data. The verification via industrial production demonstrates that the proposed model is reliable for the paper drying process. Based on the simulation results, two optimization operations have been proposed. The energy consumption decreases from 1.51 t steam/t paper to 1.44 t steam/t paper, 4.6% of the steam and 1.26 × 106 RMB can be saved for a medium-scale paper mill with the annual production capacity of 105 t paper.

This study aims at to make a heuristic analysis of energy efficiency performance of Indian paper industry in a non-parametric production theoretic approach. Using the data for 2004–05 to 2013–14, radial and non-radial variants of DEA were employed to estimate energy saving potential and identify the relative position of paper industry across the states. Preliminary analysis in terms of energy intensity scores showed declining trends of energy intensity over the period of analysis for most of the states except states like Assam, Chhattisgarh, Kerala and Punjab where it does not decline much. Assuming a variable returns to scale (VRS) technology under the conditions of inherent heterogeneity and market imperfection, the slack-based measure (SBM) reported a much higher energy saving potential than reported by other measures in the study. Further by taking scale efficiency into account, the study documented the higher contribution of pure energy inefficiency in explaining the total energy inefficiency within the paper industry relative to scale inefficiency. Finally, the study recommends the propagation of energy efficiency program through a market-based and regulatory mechanism along with consolidation and technological advancement of individual units, in order to tap vast energy saving potential and thereby ensure the growth and environmental sustainability.

The present study investigates the effect on methane production from waste paper when co-digested with macroalgal biomass. Both feedstocks were previously mechanically pretreated to reduce their particle size. The study was planned according two factors: the feedstock to inoculum (F/I) ratio and the waste paper to macroalgae (WP/MA) ratio. The F/I ratios checked were 0.2, 0.3 and 0.4 and the WP/MA ratios were 0:100, 25:75, 50:50, 75:25 and 100:0. The highest methane yield (386 L kg−1 VSadded) was achieved at an F/I ratio of 0.2 and a WP/MA ratio of 50:50. A biodegradability index of 0.87 obtained in this study indicates complete conversion of feedstock at an optimum C/N ratio of 26. Synergistic effect was found for WP/MA 25:75, 50:50 and 75:25 mixing ratios compared with the substrates mono-digestion.

The Swedish pulp and paper industry (PPI) must increase energy efficiency to remain competitive on the global market, which has experienced entries from countries with cheaper energy and raw material supplies. Interactions among variables for energy use, production, energy management, electricity price and firm characteristics (FC), in different types of mills, i.e., pulp, paper and integrated mills, in Sweden from 2006 to 2015 indicate that correlations among the studied variables were different in different types of mills. This difference between types of mills seemed to originate partly from varying accessibility to production residue that could be used for energy. For all types of mills, variation of electricity prices did not correlate significantly with energy efficiency during the study period. The studied FC were firm's age, number of employees, number of companies in company group, net sales and profit for the year. Energy efficiency was more affected by the variables characterizing energy and production compared to the variables representing FC. This study also suggested presence of possible discrepancies between FC that were perceived as barriers to energy management towards energy efficiency, according to previous studies, and what was shown by the data combining variables representing energy use, production and FC.

Bio-oil and pyrolysis gas (py-gas) are two pyrolysis products available for potential energy recovery. Crude bio-oil, however, is typically corrosive and unstable, requiring special combustion equipment or catalytic upgrading to produce drop-in-grade fuel. In contrast, py-gas is readily useable in standard equipment for energy recovery. Previous research revealed that Ca-impregnated biochar catalyst improved bio-oil to py-gas conversion. Biochar produced from paper mill sludge (p-sludge) has very high Ca content. In this study, the catalytic ability of p-sludge biochar was systematically evaluated for the first time in pyrolysis. P-sludge biochar resulted in higher py-gas yield (40 wt% of total pyrolysis products) and py-gas energy (8400 kJ of py-gas per biosolids pyrolyzed) than other biochar catalysts (e.g. wood and corn stover biochars) and mineral catalysts (e.g. calcined dolomite). Under some conditions (e.g. high temperature and catalyst loading), catalysis completely eliminated the nonaqueous phase condensate. A lower catalyst-to-feedstock ratio was required using p-sludge biochar compared to other biochars for similar performance. P-sludge biochar also had a longer catalyst lifetime based on the effectiveness over five reuse cycles. Bio-oil catalyzed by p-sludge biochar contained fewer organic constituents based on GC-MS and GC-FID analyses (e.g. toluene, ethylbenzene, styrene, phenol, cresol, and indole were not identified after catalysis).