Search

China is the top emitter of greenhouse gases in the world. Pulp and paper industry is one of eight the strictly regulated industries about carbon emission in China. However, estimates of carbon emissions from China's pulp and paper industry have been suffered from remarkable uncertainty. It is summarized that is aroused by the inaccuracy of factors evaluating energy consumption, and the huge gap between the calculation standards for assessing energy consumption in the production process and the actual level recorded in the factories. This paper re-evaluated the carbon emission of China's pulp and paper industry from the perspective of life cycle assessment, and applied more accurate emission factors, taking account of the actual energy consumption of the production process in factories, to estimate the actual carbon emissions in maximum. It is found that the national standards about the energy consumption quota of China's pulp and paper industry is no longer applicable, and the actual energy consumption regulated in the production process is far better than the advanced level given by the national standards. The greenhouse gas emission have been seriously overestimated approximately 12.00%–56.17% by international organizations. • Life Cycle Analysis of the China's pulp and paper Industry is conducted thoroughly. • The pulp flow of China's pulp and paper Industry is analyzed. • Energy regulated in factory is far better than the national standards' required. • Carbon emissions of China's pulp and paper Industry are overestimated. [ABSTRACT FROM AUTHOR]

Abstract This study aims at to make a heuristic analysis of energy efficiency performance of Indian paper industry in a non-parametric production theoretic approach. Using the data for 2004–05 to 2013–14, radial and non-radial variants of DEA were employed to estimate energy saving potential and identify the relative position of paper industry across the states. Preliminary analysis in terms of energy intensity scores showed declining trends of energy intensity over the period of analysis for most of the states except states like Assam, Chhattisgarh, Kerala and Punjab where it does not decline much. Assuming a variable returns to scale (VRS) technology under the conditions of inherent heterogeneity and market imperfection, the slack-based measure (SBM) reported a much higher energy saving potential than reported by other measures in the study. Further by taking scale efficiency into account, the study documented the higher contribution of pure energy inefficiency in explaining the total energy inefficiency within the paper industry relative to scale inefficiency. Finally, the study recommends the propagation of energy efficiency program through a market-based and regulatory mechanism along with consolidation and technological advancement of individual units, in order to tap vast energy saving potential and thereby ensure the growth and environmental sustainability. Highlights • The paper examined the energy efficiency performance of Indian paper industry. • Both radial (BCC) and the non-radial (SBM) measures of energy efficiency, were applied. • BCC measure reported an energy saving potential of 16%. • SBM measure reported an energy saving potential of 24%, higher than BCC measure. • Scale efficiency implied the relatively higher contribution of pure energy inefficiency. [ABSTRACT FROM AUTHOR]

The present study investigates the effect on methane production from waste paper when co-digested with macroalgal biomass. Both feedstocks were previously mechanically pretreated to reduce their particle size. The study was planned according two factors: the feedstock to inoculum (F/I) ratio and the waste paper to macroalgae (WP/MA) ratio. The F/I ratios checked were 0.2, 0.3 and 0.4 and the WP/MA ratios were 0:100, 25:75, 50:50, 75:25 and 100:0. The highest methane yield (386 L kg −1 VS added ) was achieved at an F/I ratio of 0.2 and a WP/MA ratio of 50:50. A biodegradability index of 0.87 obtained in this study indicates complete conversion of feedstock at an optimum C/N ratio of 26. Synergistic effect was found for WP/MA 25:75, 50:50 and 75:25 mixing ratios compared with the substrates mono-digestion. [ABSTRACT FROM AUTHOR]

Variable renewable energy-based power is expected to increase toward a sustainable society, although the power cannot be dispatched effectively due to its intermittent nature. To accelerate renewable energy implementation, we simulated energy flows of paper mills installing wind energy and evaluated their potentials to function as energy hubs for appropriate early-stage design. We targeted 39 Japanese paper mills assumed to have thermal energy storage, wind–thermal energy converters and regional woody biomass installed, and analyzed the amount of power and heat selling and life cycle greenhouse gas emissions. The results for the paper mills were compared with conventional mills to examine effective conditions for greenhouse gas reduction. The amount of power or heat selling depended on the capacity of the paper mill and the installed equipment. Most paper mills could reduce greenhouse gas using thermal energy storage, wind energy, and woody biomass. The paper mill with the highest life cycle greenhouse gas reduction, compared with conventional mills, could achieve a 190% reduction. To function as a cogeneration energy hub, the equipment installed in paper mills should be designed according to the conditions of the paper mills and their regions. • Paper mills have potential as energy hubs by integrating variable renewable energy. • Thermal energy storage and wind–thermal energy converters were studied. • Energy flows and greenhouse gas emissions of paper mills were simulated. • Most mills could provide stable power and/or heat supplies and reduce emissions. [ABSTRACT FROM AUTHOR]

In the present study, a thermodynamic analysis of a cogeneration system in a pulp and paper industry under different operating modes i.e., singular and hybrid with a variable ambient temperature is conducted according to actual operating data. For singular operating mode, the power boiler is only employed using natural gas while for hybrid operating mode, the power boiler with the recovery boiler is employed using natural gas and black liquor as main fuels, respectively. The results show that for hybrid operating mode in comparison with the singular one, the thermal efficiency of turbine and condenser is enhanced by 1.36 and 7.7%, respectively while it is reduced by 2.8% for the power boiler. In addition, the overall thermal efficiency under singular and hybrid operating modes is 87.4 and 53.7%, respectively. For hybrid operating mode, the exergy destruction of power boiler decreases by almost 10% compared with that for the singular operating mode. Also, at hybrid operating mode, the soda is recovered with a mass flow rate of 33 tons/hour that is required for the cooking process in the chemical pulp section and additionally the consumption of natural gas in the power boiler is reduced by 11.8%. [ABSTRACT FROM AUTHOR]

Increasing levels of variable renewable energy require additional flexible resources in the global energy system. In countries with energy-intensive industries, flexibility may be increased through industrial demand side management (IDSM). In most studies, the potential of IDSM is estimated from a technical or theoretical viewpoint. However, IDSM capacity is only utilized if the industry finds it profitable, and thus the economic potential should also be assessed. The focus of this paper is on the intra-day IDSM potential of a paper mill site that is active in the Nordic power market. An optimization model is built to estimate the costs that occur when the paper mill executes regulating power bids, if the original production schedule has been optimized against a spot price forecast. The costs are estimated for different sizes of bids and a marginal cost curve is provided for pricing them. Using this marginal cost curve, the market potential of the case mill site is assessed. It is found that this potential is greatly influenced by the costs of executing regulating power bids. The results indicate that transmission system operators and policy makers should account for economic factors when assessing the potential of market based IDSM. [ABSTRACT FROM AUTHOR]

Long term annual electricity consumption forecasting is very important for country's energy planning. These forecasts are influenced by several factors (political, technological, social, environmental and economic), and brings with itself a high uncertainty degree in its results and difficulties in the evaluation of such factors over them. A methodology that eases to take into account these factors aiming improve the results and help understanding the electricity consumption annual trajectory till the forecast horizon is, therefore, very much useful and desired. So, we propose a modelling structure using the bottom-up approach to cope with these matters and to evaluate the trajectory of long term annual electricity consumption of a sector of the Brazilian industry up to 2050 considering energy efficiency (EE) scenarios. It is important to emphasize that Brazil is a developing country, and to build a bottom-up approach was a challenge, mainly due to the fact that this model is data intensive. In particular, this modelling was applied in the pulp and paper sector. The main goal was to consider technological diffusion scenarios in EE measures, and show the energy savings achieved. The results point an energy savings in the order of 25% when an actual scenario is considered. [ABSTRACT FROM AUTHOR]

In this paper an original and exhaustive mathematical modelling of air impingement drying systems for the production of tissue paper in the Yankee-hoods configurations is reported, which offers the possibility to optimize its energy performance. The model takes into account many detailed operative parameters of the overall drying process with the aim to execute its energy and mass balance and to evaluate its energy performances. The validity of the mathematical model has been assessed by comparison with actual data from an existing tissue paper mill. Finally, the energy performances of two different layouts of the air system have been evaluated and compared. Changing the operative parameters of the drying process, such as air jet temperature and speed and moisture content of the extraction air, it is possible to obtain the same paper production with an energy saving of about 4.5%. In average, the layout with two parallel air circuits assure an energy saving of about 1% with respect to the layout with a single air circuit. [ABSTRACT FROM AUTHOR]

The waste biomass has immense opportunities and plenty of potentials to be an efficient source of renewable energy. Initially, native unripe coconut husk (NCH) was used as raw material for fluidized bed gasification. Then NCH was treated with paper and pulp waste water to impregnate metals present in it for getting enhanced H 2 yield in fuel gas. Humidified air was used as gasifying medium, which served the purpose of introducing water vapour to take part in the gasification process. Then after, gasification medium was retrofitted with CO 2 , which enhanced both the higher heating value (HHV), and CO and H 2 content in the fuel gas. This research serves the dual benefit of energy generation and waste minimization. HHV of unripe coconut husk was investigated and found to be 20.95 MJ/kg. H 2 yield and HHV from impregnated coconut husk (ICH) were obtained as 55.55 vol % and 5.24 MJ/Nm3, respectively at HER 0.1 and gasification temperature of 850 °C in case of fluidized bed gasification. The GC-MS analysis of fuel oil obtained from ICH gasification was done to get the information about high yield of fuel gas as promise product of fluidized bed gasification. • Humidified air fluidized bed gasification of coconut husk with CO 2 was performed. • Paper and pulp wastewater was used for metals impregnation onto coconut husk. • Hydrogen content increased in humidified air gasification of treated coconut husk. • CH 4 in fuel gas decreased for humidified air with CO 2 resulting in decrease of HHV. • GC-MS fuel oil analysis resulted less number of elements showing higher gas yield. [ABSTRACT FROM AUTHOR]

Magazines and newspapers, as two kinds of municipal solid waste, were investigated as the fuel feedstock in a hybrid direct carbon fuel cell. These carbon sources, together with a reference carbon source-activated charcoal, were characterized by such techniques as X-ray diffraction spectra, X-ray photoelectron spectroscopy, and thermal gravimetric analysis, among others. The results indicate that the carbon from magazine waste paper was more abundant in calcite and magnesium calcite, with more oxidation degree of carbon and higher thermal reactivity, compared with the other two carbon sources. Then, the cell performance fed with such carbon sources was tested in a homemade device. The cell fed with magazine waste paper carbon showed the highest performance among the three carbon sources, with a peak power density of 172 mW/cm 2 at 650 °C. The cell performance results indicated that waste paper carbon sources, with a surface containing certain inherent impurities (calcite and magnesium calcite) and a high oxidation degree of carbon, could favor the thermal gasification of carbon fuel, and thus considerably enhance cell performance, especially for the operating temperatures below 700 °C. This study demonstrated that waste paper carbon sources could be promising fuel feedstock for hybrid direct carbon fuel cells. [ABSTRACT FROM AUTHOR]