Search

To investigate the impact of blending natural gas with hydrogen on the combustion performance of partially premixed gas water heaters, a framelet-generated manifold (FGM) was employed for lower-order simulation of combustion processes. Coupled with the 30-step methane combustion mechanism simplified by GRI3.0, a three-dimensional computational fluid dynamics (CFD) simulation of the combustion chamber of a partially premixed gas water heater was carried out. A numerical simulation was performed to analyze the combustion process of a mixture including 0–40% natural gas and hydrogen in the combustion chamber of a partially premixed gas water heater. The results indicate that the appropriate hydrogen blending ratio for some premixed gas water heaters should be less than 20%. Furthermore, it was observed that after blending hydrogen, there was a significant increase in the combustion temperature of the water heater. Additionally, there was a slight increase in NOx. [ABSTRACT FROM AUTHOR]

This study focused on assessing the financial efficiency of investing in a horizontal shower heat exchanger. The analysis was based on net present value (NPV). The research also examined the possibility of using artificial neural networks and SHapley Additive exPlanation (SHAP) analysis to assess the profitability of the investment and the significance of individual parameters affecting the NPV of the project related to installing the heat exchanger in buildings. Comprehensive research was conducted, considering a wide range of input parameters. As a result, 1,215,000 NPV values were obtained, ranging from EUR −1996.40 to EUR 36,933.83. Based on these values, artificial neural network models were generated, and the one exhibiting the highest accuracy in prediction was selected (R2 ≈ 0.999, RMSE ≈ 57). SHAP analysis identified total daily shower length and initial energy price as key factors influencing the profitability of the shower heat exchanger. The least influential parameter was found to be the efficiency of the hot water heater. The research results can contribute to improving systems for assessing the profitability of investments in shower heat exchangers. The application of the developed model can also help in selecting appropriate technical parameters of the system to achieve maximum financial benefits. [ABSTRACT FROM AUTHOR]

Shutdowns of photovoltaic installations are a problem that has been increasingly affecting private investors who have built home installations of several to a dozen kWp over the last few years. This problem, most often caused by outdated infrastructure, appears in many countries and impacts energy production. This work focuses on three aspects of the problem. The first one answers the question of how shutdowns of the photovoltaic installation affect production, and how significant the energy loss happens when the PV inverter is not working or is in the restart phase. The second aspect proposes an original, low-cost method that reduces the number of shutdowns. This method relates to the auto-consumption mechanism associated with domestic water heaters and the system for measuring voltage and energy consumption from the electrical network. The solution is based on constant monitoring of the network voltage and the switching of heaters based on a dedicated algorithm. Additionally, continuous analysis also allows for reporting observed irregularities to the electricity supplier. The third and final factor corresponds to the real impact of shutdowns on the long-term aspect of the investment and the extension of its payback period, and to what extent the proposed solution shortens this period. Through a detailed analysis on the issue of shutdowns, the proposed solution allows for a reduction in the number of shutdowns by over 40%. However, due to the fact that it discusses a specific case, this solution requires a calibration and adjustment process, which is discussed in the article. [ABSTRACT FROM AUTHOR]

To improve the heat transfer coefficient of a condenser, this paper proposes using a fin-tube condenser to replace a smooth-tube condenser in a domestic heat pump water heater. The finite element method is used to analyze the heat transfer coefficient of fin-tube condensers with different design parameters. By comparing the results of experiments with those obtained using CFD methods, it has been determined that the CFD method used in this study is feasible. Simulation results showed that the heat transfer coefficient enhanced clearly. The total thermal resistance of the fin-tube condenser decreased by 7% through increasing fin thickness. The total thermal resistance of the fin-tube condenser increased by 1–1.3% when fin spacing was increased. The heat transfer coefficient decreased severely and the maximum total thermal resistance of the fin-tube condenser increased by 8.7% with increasing fin height. In 600 s, when the fin spacing, fin height, fin thickness and inner diameter were 14 mm, 12.5 mm, 1.2 mm and 22.5 mm, respectively, compared to the smooth-tube condenser, the fin-tube condenser could increase the final water temperature by 18.37%, and the heat transfer coefficient would increase by about 95%. This research could provide a low-cost way to improve the heat transfer coefficient of condensers in domestic heat pump water heaters. [ABSTRACT FROM AUTHOR]

The paper presents a cause-and-effect analysis of the failure of a 130 MWt gas-fired water boiler. The fault was a rupture of the helically finned tubes in the first rows of the second-stage water heater (ECO2). The high frequency of failures forced the boiler user to investigate their causes. The rapid drop in water flow in the ECO2 and the tightly finned pipes suggested that the permissible operating temperature of the steel used was exceeded. The only possible way to assess the working conditions was through a CFD simulation of the operation of the ECO2. Validated with the data acquisition system, the results show that the main reason for the failure was the overheating of the first rows of finned water heater pipes, regardless of the boiler load. The high heat flux value, exceeding 500,000 W/m2, and the increased flue gas temperature in front of the ECO2, almost reaching 900 °C, affected the appearance of the boiling film, limiting the cooling of the tube wall. Heat radiation and eddies behind the tubes significantly impacted the non-uniform temperature distribution, resulting in high pipe wall stress. By analyzing the service life of the first row of pipes based on the Larson–Miller parameter, it was concluded that the pipes would fail after only a few tens of hours. [ABSTRACT FROM AUTHOR]

The influence of flow step ratio (FSR) on the startup characteristics of instant heat pump water heaters (IHPWHs) with natural mixture M (R744/R290 (12/88)) under nominal conditions was studied experimentally to verify the feasibility of a new quick startup method. The results show that the FSR had a marked effect on the startup time of system performance parameters. Under the optimal FSR of 0.6, the shortest system startup time and available hot water supply time were 700 s and 250 s, respectively, which were markedly shorter than those in the conventional startup. Therefore, rapid startup of the system and rapid production of usable domestic hot water can be realized by controlling the flow step. The influence of flow step on the variation trend of system performance parameters was obviously different, and there was no slow warming section for the heat sink outlet temperature (HSOT) under three FSRs. The HSOT, heating capacity, and high pressure side pressures had the maximum values in the quick startup, and the maximum values were obviously affected by the FSR. The FSR had no marked effect on the minimum suction pressure. The refrigerant pressures and refrigerant temperatures fluctuated markedly in both rapid and conventional starts. [ABSTRACT FROM AUTHOR]

As the smart grid involves more new technologies such as electric vehicles (EVs) and distributed energy resources (DERs), more attention is needed in research to general energy storage (GES) based energy management systems (EMS) that account for all possible load shifting and control strategies, specifically with major appliances that are projected to continue electrification such as the electric water heater (EWH). In this work, a methodology for a modified single-node model of a resistive EWH is proposed with improved internal tank temperature for user comfort modeling and capabilities for conservation voltage reduction (CVR) simulations as well as Energy Star and Consumer Technology Association communications protocol (CTA-2045) compliant controls, including energy storage calculations for "energy take". Daily and weekly simulations are performed on a representative IEEE test feeder distribution system with experimental load and hot water draw (HWD) profiles to consider user comfort. Sequential controls are developed to reduce power spikes from controls and lead to peak shavings. It is found that EWHs are suitable for virtual power plant (VPP) operation with sustainable tank temperatures, i.e., average water temperature is maintained at set-point or above at the end of the control period while shifting up to 78% of EWH energy out of shed windows per day and 75% over a week, which amounts to up to 23% of the total load shifted on the example power system. While CVR simulations reduced the peak power of individual EWHs, the aggregation effect at the distribution level negates this reduction in power for the community. The EWH is shown as an energy constant load without consistent benefit from CVR across the example community with low energy reductions of less than 0.1% and, in some cases, increased daily energy by 0.18%. [ABSTRACT FROM AUTHOR]

In the global trend towards decarbonization, peer-to-peer (P2P) energy trading is garnering increasing attention. Furthermore, energy management on the demand side plays a crucial role in decarbonization efforts. The authors have previously developed an automated bidding agent that considers user preferences for renewable energy (RE), assuming users own electric vehicles (EVs). In this study, we expand upon this work by considering users who own not only EVs but also heat pump water heaters, and we develop an automated bidding agent that takes into account their preferences for RE. We propose a method to control the start time and presence of daytime operation shifts for heat pump water heaters, leveraging their daytime operation shift function. Demonstration experiments were conducted to effectively control devices such as EVs and heat pumps using the agent. The results of the experiments revealed that by controlling the daytime operation of heat pumps with our method, the RE utilization rate can be improved compared to scenarios without daytime operation shifts. Furthermore, we developed a simulator to verify the outcomes under different scenarios of demand-side resource ownership rates, demonstrating that higher ownership rates of EVs and heat pumps enable more effective utilization of renewable energy, and that this effect is further enhanced through P2P trading. Based on these findings, we recommend promoting the adoption of demand-side resources such as EVs and heat pumps and encouraging P2P energy trading to maximize the utilization of renewable energy in future energy systems. [ABSTRACT FROM AUTHOR]

The anaerobic digestion of New Zealand low-input dairy farms has previously been evaluated for energy production, but farming systems have recently become more intensive with increased feed supplementation and feed replacement; therefore, we are studying how these changes affect the overall energy production for water heating. A combination of literature review, surveys, chemical analyses, biomethane potential analysis, and modeling were used for this study. On a case study farm with a solid separator, it was found that 558 MJ/day and 176–861 MJ/day could be produced with the solid and liquid portions of effluent, respectively. There is enough biogas to satisfy the dairy farm's water heating requirements with a tankless water heater. [ABSTRACT FROM AUTHOR]

Greenhouse gas (GHG) emissions have significantly increased in recent years as a result of population rise and the increase in the number of residences, with high levels of energy use in homes and household appliances. It is crucial to move the housing industry away from high-carbon sources and toward low-carbon sources in order to minimize greenhouse gas emissions as a precaution. One of the most crucial systems that needs to be provided in order to achieve energy efficiency is the electric water heater (EWH), as they rank among the top electricity consumers. In this study, a double-tank EWH model was developed and simulated at various tank sizes (100 L, 200 L, 300 L and 400 L) and power ratios (1 kW, 2 kW, 3kW and 4 kW) in order to demonstrate energy efficiency. To obtain information for the simulation analysis of the tanks, the hourly water usage of 25 houses was measured. The single-tank and the double-tank models created for this study were both run in the Matlab/Simulink environment with an on-off controller applied, and their energy consumption was compared. Amounts were also determined based on how much energy both tanks consumed. It has been noted that the amount of GHG emissions is also reduced because the double tank uses less energy than the single tank does. The simulation showed that compared to the single tank, the dual tank produced 46.62% less GHG emissions at 45 W power and 47.51% less GHG emissions at 80 W. [ABSTRACT FROM AUTHOR]

Waste heat air-source heat pump water heater (WH-ASHPWH) systems have been widely used to provide water heating in buildings due to their advantages of high efficiency and low environmental impact. It is important to determine reasonable operating conditions for WH-ASHPWH systems to improve their heating efficiency, especially for systems using industrial waste heat. In this study, a semiempirical parametric model of a WH-ASHPWH system was established to simulate heating performance under different working conditions and determine the optimum operating range of the system. A new discrete model for a tube-in-tube condenser was also generated. Taking the equipment of a pharmaceutical factory as an example, the heat exchanger model was first calibrated; then, the global model was used to study the effects of different air-side and condenser-side waste heat conditions on the heating performance of the system. According to the simulation results, the coefficient of performance (COP) reached a maximum value of 4.5 under the optimum working conditions. The deviation between the COP simulation data and experimental values was less than 8.28%, and the simulation time was less than 8 min. These metrics indicate that the model is reasonable and efficient. [ABSTRACT FROM AUTHOR]

Considering the excellent environmental properties and heating capability under wide running conditions of the natural fluid CO2, the transcritical CO2 heat pump system has widely been used in the application of water heaters, commercial heating and cooling, electric vehicle thermal management, etc. Since the performance was highly affected by the discharge pressure and heat recovery rate in a transcritical CO2 system, the collaborative optimization of these two parameters was analyzed in detail in this study. The results showed that the optimal value of the system heating COP, which was the ration of heating capacity to power consumption, was better under a higher heat recovery rate and relatively lower discharge pressure, which is why these kinds of operating conditions are highly recommended from the perspective of collaborative optimization. Additionally, the heat recovery rate had a positive effect on the system performance when the discharge pressure was lower than its optimal value, while the heat recovery rate would present a passive effect on the system performance when the discharge pressure was higher than its optimal value. The relevant conclusions of this study provide a good theoretical basis for the efficient and stable operation of the transcritical CO2 heat pump technology under the conditions of a wide ambient temperature range. [ABSTRACT FROM AUTHOR]

This paper focused on the performance monitoring and modeling of a 6.0 kW, 2000 L hybrid direct expansion solar assisted heat pump (DX-SAHP) water heater used for the production of hot water in a university students' accommodation with 123 females. The data of total electrical energy consumed, volume of hot water consumed, ambient temperature, relative humidity, and solar irradiance were obtained from the data acquisition systems and analyzed in conjunction with the energy factor (EF) of the system. A multiple linear regression model was developed to predict the EF. The EF of the hybrid DX-SAHP water heater was determined from the summation of the coefficient of performance (COP) of the heat pump unit and the solar fraction (SF) of the solar collectors. The operations of the hybrid energy system were analyzed based on three phases (first phase from 00:00–08:00, second phase from 08:30–18:30, and third phase from 19:00–23:30) over 24 h for the entire monitoring period. The average EF of the hybrid energy system per day during the second phase of operation was 4.38, while the SF and COP were 0.697 and 3.683, respectively. The developed multiple linear regression model for the hybrid DX-SAHP water heater accurately predicted the determined EF. [ABSTRACT FROM AUTHOR]

Evacuated tube solar water heaters are gaining more attention in the present market scenario as compared to conventional collectors. Such collectors are versatile because no solar tracking is required and the operating temperature range is also broad. Comparatively, it is cost-effective and may attain higher thermal efficiency. However, like other collectors, continuous energy supply is sometimes hampered by the intermittent nature of solar radiation. This problem can be partially resolved by using phase change materials (PCM) in the evacuated tube solar collector (ETC). PCMs can store the energy during the sunshine hours, which can be released when solar energy is not available. In the literature, several studies are available pertaining to the use of PCMs in ETC-based solar water heaters. The literature indicates that the integration of PCMs with ETCs has several merits. Nevertheless, systematic, and comprehensive review papers dedicated to such integrated energy storage systems with ETC solar water heaters are not available. Hence, the objective of this work is to compile the relevant experimental, numerical, and theoretical works reported in the literature. The present paper broadly reviews the recent design modifications, PCM integration with different kinds of ETC water heaters, and their life cycle assessment. Furthermore, studies in the literature pertaining to the application of nanoparticles in ETC systems are also discussed, and finally, a roadmap for this energy storage system is provided. [ABSTRACT FROM AUTHOR]

Temperature-control loads, such as residential air conditioners (ACs) and electric water heaters (EWHs), have become important demand response resources in the power system. However, due to the impact of various factors on users' response behavior, it has been difficult for power grid operators to accurately evaluate the response potential under complex factor relationships to derive optimal incentive strategy. Therefore, it cannot achieve a win-win economic benefit between the grid and users. In this paper, a method combining Analytic Network Process (ANP) and Fuzzy logical inference is proposed to predict the user's willingness firstly by taking residential AC load as an example. The weight of each factor affecting users' willingness is analyzed, and main factors are selected as inputs of fuzzy logic inference to derive the willingness of the resident to actively regulate the AC. Then, this method is applied in evaluating the response potential of certain residential area in Beijing according to the survey. By further considering users' house size and the sacrificed comfort temperature under the incentive strategy, the power potential curve of the AC load under different incentives is obtained by using the first-order equivalent thermal parameter (ETP) model and the regulation willingness. Finally, with the objective of maximizing the consumption of the photovoltaic (PV) power, the optimal operation is achieved through the coordinated regulation of residential ACs and EWHs based on the potential curve, and the corresponding optimal incentive strategy for the flexible temperature-control loads is obtained. Simulation results show that the optimal incentive strategy proposed not only increases the PV consumption ratio to 98.35% with an increase of 24.71%, but also maximizes the economic benefits of both sides of the power grid and users. This method of deriving incentive strategy can be used as a reference for grid companies to formulate the incentive strategy to realize optimal operation, such as the maximum new energy consumption. [ABSTRACT FROM AUTHOR]

This paper ascertained the performance of the evacuated tube solar water heater (SWH) coupled with an auxiliary electric heater with reference to the replaced electric water heater with the same storage tank capacity (200 L) in a building. It also examines the influence of the uptake of the SWHs in the community due to different campaign methods. The study evaluated the performance of a 4 kW electric water heater and a 2 kW input SWH with an auxiliary electric heater, and quantified the annual energy and cost savings. A survey using questionnaires was conducted among 150 residences in Dimbaza based on the house representative's perceptions to replace their electric water heaters with solar water heaters (based on the monetary saving inscribed on the solar water heaters, the sensitization of the target population on the environmental benefits of the solar water heaters and both the monetary savings and environmental benefits). The findings revealed that by replacing the electric water heater with the solar water heater with an auxiliary electric heater, the annual electricity savings due to hot water heating was 4408.99 kWh and the net present value payback period was 4.32 years. The desire of the household representatives to replace their existing electric water heaters with solar water heaters due to the campaign strategies increased from 75 to 126. This study is capable of providing a mechanism to increase the penetration of solar water heaters and justifying the techno-economic viability of solar water heaters. [ABSTRACT FROM AUTHOR]

Wastewater has significant potential as a source of clean energy. This energy can be used both within external sewer networks and on the scale of individual residential buildings, and the use of shower heat exchangers appears to be the most reasonable solution. However, in the case of Poland, the problem is still the unwillingness of society to use this type of solution, caused mainly by the lack of space for the installation of vertical drain water heat recovery (DWHR) units and the low efficiency of horizontal units. In response to this issue, the efficiency of a new compact shower heat exchanger designed to be mounted below the shower tray, as well as its linear counterpart, was investigated under various operating conditions. In addition, the financial efficiency of using the compact DWHR unit with average water consumption for showering was evaluated. For this purpose, discount methods were used to estimate the financial efficiency of investments. The study showed that the compact shower heat exchanger has higher efficiency than its linear counterpart. Depending on the temperature of cold water and the flow rate of both media through the heat exchanger, it achieves efficiencies ranging from 22.43% to 31.82%, while the efficiency of the linear DWHR unit did not exceed 23.03% in the study. The financial analysis showed that its use is particularly beneficial when the building uses an electric hot water heater. The investment's sensitivity to changes in the independent variables is small in this case, even with low water consumption per shower. The only exceptions are investment outlays. Therefore, the compact DWHR unit is a clean energy device, which in many cases is financially viable. [ABSTRACT FROM AUTHOR]

Electric water heaters, which have the capacity to act as thermal energy storage, are well suited to demand management strategies in smart grid applications. However, finding the balance between managing power load, reducing thermal energy losses, user's convenience, and bacterial growth control, requires accurate modelling of the internal thermal dynamics of the tank, including stratification. As a black box, this unknown is dependent on a multitude of environmental factors (e.g., ambient temperature and inlet temperature), water draw patterns, scheduling, set temperatures and orientation of the vessel. The latter affects the stratification and temperature variation inside the tank, and therefore has a direct bearing on the balancing act of demand management. Although this has been assessed inside vertically oriented tanks, what happens inside the horizontal variety—ubiquitous in developing countries—is currently left to the guesswork. In this paper, we present the development of an embedded hardware and software platform with which the temperature variations inside a horizontal water heater can be characterised under numerous environmental and usage conditions. The importance of doing so is highlighted by the preliminary results, which clearly show the expected substantial temperature variation along the vertical axis, but also show interesting phenomena along the longitudinal and transverse axes, for both static (no water draw) and dynamic (with water draw) conditions. We conclude by highlighting potential for further research. [ABSTRACT FROM AUTHOR]

Consumers are always influenced by external information before making decisions to purchase energy-saving electric appliances. However, the effects of different information sources are overlooked by previous studies. As a kind of green and safe appliance, the Heat Pump Water Heater (HPWH) is expected to be popular in the Chinese market. This study, based on an investigation in eastern China, will reveal the attitudes of potential consumers to HPWHs and verify the effects of different information sources. The results show that official information (Information from enterprises and governments) can arouse consumers' positive attitudes toward HPWHs, yet can significantly reduce perceived usefulness among consumers, while unofficial information (Information from relatives and friends) negatively affects their attitudes. Although HPWHs are billed as energy-saving and eco-friendly appliances, consumers can obtain different information from online or offline interpersonal communications to obtain user feedback (which might be negative) before purchase. Some suggestions are proposed to promote energy-saving appliances. [ABSTRACT FROM AUTHOR]

Compound parabolic concentrators are relevant systems used in solar thermal technology. With adequate tailoring, they can be used as an efficient and low-cost alternative in residential water heating applications. This work presents a simulation study using a ray tracing analysis. With this technique, we simulate the interaction between solar rays and solar concentrator to quantify the amount of energy that impinges on the receiver at a particular time. Energy availability is evaluated in a comparison of two configurations throughout the year: static setup at 21° and multi-position setup; tilted with respect to the horizontal, depending on three seasonal positions: 0° for summer, 16° for spring/autumn, and 32° for winter, with the aim to evaluate the amount of available energy in each season. The fact that a tracking system can be dispensed with also represents an economical option for the proposed application. The results showed that at 21°, the proposed solar Compound Parabolic Concentrator (CPC) works satisfactorily; however, by carrying out the selected angular adjustments, the overall energy availability increased by 22%, resulting in a more efficient option. The most effective design was also built and analyzed outdoors. The obtained thermal efficiency was of ~43%. The optical design and its evaluation developed herein proved to be a valuable tool for prototype design and performance evaluation. [ABSTRACT FROM AUTHOR]

Besides compressor rotary speed and parameters of water flowing through gas cooler and evaporator, refrigerant charge amount and electronic expansion valve (EEV) opening are two important parameters that have significant effects on the performance of a transcritical CO2 heat pump system. In this study, the effects of refrigerant charge amount on the performance of a transcritical CO2 heat pump water heater were investigated experimentally at different EEV openings. An optimal coefficient of performance (COP) was found that corresponded to a specific refrigerant charge and a specific EEV opening. Based on the experiment, the COP peaked at charge of 1.8 kg when EEV opening was 40% of full opening. The heating capacity and the COP increased at first, reached peaks and then decreased with increase of charge amount. The COP decreased 14.95% as the CO2 charge amount was reduced by 22.2% from the optimal charge at 50% EEV opening. As EEV opening varied from 40% to 60% at the same charge amount, the heating capacity decreased more than 30%. [ABSTRACT FROM AUTHOR]

The effect of the discharge pressure on the performance of the trans-critical CO2 heat pump with a low gas-cooler outlet temperature is experimentally investigated on a test rig of water source heat-pump water heater. The optimal discharge pressure of the trans-critical CO2 heat pump is investigated under different external operation conditions. When the tap-water temperature is low, the characteristic of the S-shape isotherm at the supercritical region has little effect on the occurrence of the optimal discharge pressure; while the mass flow rate of CO2, the suction pressure and the gas-cooler outlet temperature play a significant role in determining the emergence of the optimal discharge pressure. At the optimal discharge pressure, the COP reaches the peak; however, the corresponding heating capacity is still lower than its maximum, which is reached as the discharge pressure is slightly above the optimal discharge pressure. Reducing the tap-water flowrate or increasing the water-source temperature can increase the optimal discharge pressure. The COP is positively dependent on both the tap-water flowrate and the water-source temperature. In addition, the tap-water flowrate has a negligible influence on the maximum heating capacity while increasing the water-source temperature can greatly enhance the heating capacity. [ABSTRACT FROM AUTHOR]

Frequency is an important parameter of a power system. It is of great significance to maintain its stability, especially in the current development scenario of large-scale interconnected power systems. Thermostatically controlled appliances (TCAs) are good controllable resources for demand response owing to their rapid response capabilities and relatively wide controllable ranges. In this study, domestic water heaters, which have wider deadbands compared with other typical TCAs, such as heat pumps, are used as frequency regulation resources. The main contribution of this paper is that it proposes a queuing-controlled strategy with lock-on and off constraints for controlling an efficient power plant consisting of water heaters (EPP-WH). The queuing-controlled strategy enables TCAs to provide frequency regulation ancillary service for the normal operation of the power system. The thermal dynamic process of the water heater and the formation of the EPP-WH are first discussed. Based on the developed model, a series of strategies are proposed, including load shedding calculation, top layer optimization, and improved temperature priority list (TPL) strategy with lock-on and off constraints. Finally, typical case studies are discussed to illustrate the frequency regulation effects and the effects of two characteristic parameters--users' willingness and lock time limits. Reasonable targets are generated based on various consideration from top layer optimization module. The results indicate that using the model and proposed strategies, the EPP-WH has good frequency regulation performance. [ABSTRACT FROM AUTHOR]

This article proposes a dual heat source heat pump bathroom unit with preheater which is feasible for a single family. The system effectively integrates the air source heat pump (ASHP) and wastewater source heat pump (WSHP) technologies, and incorporates a preheater to recover shower wastewater heat and thus improve the total coefficient of performance (COP) of the system, and it has no electric auxiliary heating device, which is favorable to improve the security of the system operation. The process simulation software ASPEN PLUS, widely used in the design and optimization of thermodynamic systems, was used to simulate various cases of system use and to analyze the impact of the preheater on the system. The average COP value of a system with preheater is 6.588 and without preheater it is 4.677. Based on the optimization and analysis, under the standard conditions of air at 25 °C, relative humidity of 70%, wastewater at 35 °C, wastewater flow rate of 0.07 kg/s, tap water at 15 °C, and condenser outlet water temperature at 50 °C, the theoretical COP of the system can reach 9.784 at an evaporating temperature of 14.96 °C, condensing temperature of 48.74 °C, and preheated water temperature of 27.19 °C. [ABSTRACT FROM AUTHOR]

This paper proposes and analyses a new demand response technique for renewable energy regulation using smart hot water heaters that forecast water consumption at an individual dwelling level. Distributed thermal energy storage has many advantages, including high overall efficiency, use of existing infrastructure and a distributed nature. In addition, the use of a smart thermostatic controller enables the prediction of required water amounts and keeps temperatures at a level that minimises user discomfort while reacting to variations in the electricity network. Three cases are compared in this paper, normal operation, operation with demand response and operation following the proposed demand response mechanism that uses consumption forecasts. The results show that this technique can produce both up and down regulation, as well as increase water heater efficiency. When controlling water heaters without consumption forecast, the users experience discomfort in the form of hot water shortage, but after the full technique is applied, the shortage level drops to nearly the starting point. The amount of regulation power from a single dwelling is also discussed in this paper. [ABSTRACT FROM AUTHOR]

The integration of large-scale renewable energy poses great challenges for the operation of power system because of its increased frequency fluctuations. More load frequency control (LFC) resources are demanded in order to maintain a stable system with more renewable energy injected. Unlike the costly LFC resources on generation side, the thermostatically controlled loads (TCLs) on the demand side become an attractive solution on account of its substantial quantities and heat-storage capacity. It generally contains air conditioners (ACs), water heaters and fridges. In this paper, the supplementary LFC is extracted by the modeling and controlling of aggregated ACs. We first present a control framework integrating the supplementary LFC with the traditional LFC. Then, a change-time-priority-list method is proposed to control power output taking into account customers' satisfaction. Simulations on a single-area power system with wind power integration demonstrate the effectiveness of the proposed method. The impact of ambient temperature changes and customer preferences on room temperature is also involved in the discussion. Results show that the supplementary LFC provided by ACs could closely track the LFC signals and effectively reduce the frequency deviation. [ABSTRACT FROM AUTHOR]

This paper presents the design, modelling and performance evaluation of a photovoltaic/thermal-assisted heat pump water heating (PVTA-HPWH) system. The cooling effect of a refrigerant simultaneously enhances the PVT efficiency and effectively improves the coefficient of performance (COP) of the HPWH system. The proposed model was built in the MATLAB/Simulink environment by considering the reciprocal energy exchange between a PVT evaporator and a HPWH system. In addition, the power consumption needs of the HPWH are provided by the PV electricity using a model-based control methodology. System performance is evaluated through a real field test. The results have demonstrated the power autarchy of the proposed PVTA-HPWH system with better PVT efficiency and COP. In addition, the good agreement between the model simulation and the experimental measurements demonstrate the proposed model with sufficient confidence. [ABSTRACT FROM AUTHOR]

Several North American utilities are planning to blend hydrogen into gas grids, as a short-term way of addressing the scalable demand for hydrogen and as a long-term decarbonization strategy for 'difficult-to-electrify' end uses. This study documents the impact of 0–30% hydrogen blends by volume on the performance, emissions, and safety of unadjusted equipment in a simulated use environment, focusing on prevalent partially premixed combustion designs. Following a thorough literature review, the authors describe three sets of results: operating standard and "ultra-low NOx" burners from common heating equipment in "simulators" with hydrogen/methane blends up to 30% by volume, in situ testing of the same heating equipment, and field sampling of a wider range of equipment with 0–10% hydrogen/natural gas blends at a utility-owned training facility. The equipment was successfully operated with up to 30% hydrogen-blended fuels, with limited visual changes to flames, and key trends emerged: (a) a decrease in the input rate from 0 to 30% H2 up to 11%, often in excess of the Wobbe Index-based predictions; (b) NOx and CO emissions are flat or decline (air-free or energy-adjusted basis) with increasing hydrogen blending; and (c) a minor decrease (1.2%) or increase (0.9%) in efficiency from 0 to 30% hydrogen blends for standard versus ultra-low NOx-type water heaters, respectively. [ABSTRACT FROM AUTHOR]

Breakthroughs in smart grid technology make it possible to deliver electricity in controlled and intelligent ways to improve energy efficiency between the user and the utility. Demand-side management strategies can reduce overall energy usage and shift consumption to reduce peak loads. Electric water heaters account for 40% of residential energy consumption. Since they are thermal storage devices, advanced control strategies can improve their efficiency. However, existing methods disregard the connection between the user and the grid. We propose a centrally adapted control model that allows for coordinated scheduling to adapt the optimal control schedule of each EWH, spreading the load into off-peak periods to ensure that the grid's generation capacity is not exceeded. We consider two strategies for the delivery of hot water: temperature matching, and energy matching with Legionella sterilisation, and compare them to a baseline strategy where the thermostat is always switched on. Simulation results for a grid of 77 EWHs showed that an unconstrained peak load of 1.05 kW/EWH can be reduced as low as 0.4 kW/EWH and achieve a median energy saving per EWH of 0.38 kWh/day for the temperature matching strategy and 0.64 kWh/day for the energy matching strategy, without reducing the user's comfort. [ABSTRACT FROM AUTHOR]

In the EU 28, the installed heating appliance stock is quite old, with an actual replacement rate of 4%. This is directly reflected in the average efficiency of the installed heating systems, where around 60% of the stock is rated with an energy class of C or D (the lowest classes of the energy label scale). The European project HARP aims at raising consumers' awareness of the planned replacement of their old and inefficient heating appliances with more efficient and renewable solutions. In this direction, an energy labeling methodology for old appliances has been developed to rate the installed stock before the introduction of the EU energy label. The methodology has been developed for space heating appliances and water heaters, targeting two types of users: end consumers and professional users. The validation considered about 4600 space heating appliances and 800 water heaters built between 1972 and 2019. Three heating appliances and two water heaters were tested in the laboratory, confirming the reliability of the proposed methodology. The expected impact of defining an energy labeling methodology for installed heating appliances increases the current replacement rate of these appliances in the EU from 4% to 5%. [ABSTRACT FROM AUTHOR]

In this study, the effects of the mixing chamber diameter (Dm), mixing chamber length (Lm) and pre-mixing chamber converging angle (θpm) were numerically investigated for a two-throat nozzle ejector to be utilized in a CO2 refrigeration cycle. The developed simulated method was validated by actual experimental data of a CO2 ejector in heat pump water heater system from the published literature. The main results revealed that the two-throat nozzle ejectors can obtain better performance with Dm in the range of 8–9 mm, Lm in the range of 64–82 mm and θpm at approximately 60°, respectively. Deviation from its optimal value could lead to a poor operational performance. Therefore, the mixing chamber structural parameters should be designed at the scope around its optimal value to guarantee the two-throat nozzle ejector performance. The following research can be developed around the two-throat nozzle geometries to strengthen the ejector performance. [ABSTRACT FROM AUTHOR]

The operation of water heating uses a substantial amount of energy and is responsible for 30% of a household's overall electricity consumption. Determining methods of reducing energy demand is crucial for countries such as South Africa, where energy supply is almost exclusively electrical, 88% of it is generated by coal, and energy deficits cause frequent blackouts. Decreasing the energy consumption of tanked water heaters can be achieved by reducing the standing losses and thermal energy of the hot water used. In this paper, we evaluate various energy-saving strategies that have commonly been used and determine which strategy is best. These strategies include optimising the heating schedule, lowering the set-point temperature, reducing the volume of hot water used, and installing additional thermal insulation. The results show that the best strategy was providing optimal control of the heating element, and savings of 16.3% were achieved. This study also determined that the magnitude of energy savings is heavily dependent on a household's water usage intensity and seasonality. [ABSTRACT FROM AUTHOR]

Given the large demand nowadays for domestic hot water, and its impact on modern building energy consumption, air source transcritical CO2 heat pumps have been extensively adopted for hot water production. Since their system efficiency is limited by significant irreversibility, a CO2-based mixture could offer a promising drop-in technology to overcome this deficiency without increasing system complexity. Although many CO2 blends have been studied in previously published literature, little has been presented about the CO2/R32 mixture. Therefore, a proposed mixture for use in transcritical CO2 heat pumps was analyzed using energy and exergy analysis. Results showed that the coefficient of performance and exergy efficiency variation displayed an "M" shape trend, and the optimal CO2/R32 mixture concentration was determined as 0.9/0.1 with regard to flammability and efficiency. The irreversibility of the throttling valve was reduced from 0.031 to 0.009 kW⋅kW−1 and the total irreversibility reduction was more notable with ambient temperature variation. A case study was also conducted to examine domestic hot water demand during the year. Pure CO2 and the proposed CO2 blend were compared with regard to annual performance factor and annual exergy efficiency, and the findings could provide guidance for practical applications in the future. [ABSTRACT FROM AUTHOR]

In the context of a world energy crisis, the only solution to control the situation is in the management of energy. One of the most important management keys is the optimization of electrical components. This article presents a complete numerical and experimental study aiming for the optimization of electrical water heaters for household use. The optimization conceives the minimization of energy consumption simultaneously with the minimization of time to heat water. Firstly, a thermal model well adapted for the case of heaters is constructed and validated experimentally and then a parametric study is conducted covering all the input power, the volume and the external area of the heater. Results are promising, showing significant energy savings are possible with an optimum setting of these parameters, thus presenting a firm tool for the optimization of heaters. [ABSTRACT FROM AUTHOR]

Penetration of equipment such as photovoltaic power generations (PV), heat pump water heaters (HP), and electric vehicles (EV) introduces voltage unbalance issues in distribution systems. Controlling PV and energy storage system (ESS) outputs or coordinated EV charging are investigated for voltage unbalance compensation. However, some issues exist, such as dependency on installed capacity and fairness among consumers. Therefore, the ideal way to mitigate unbalanced voltages is to use grid-side equipment mainly. This paper proposes a voltage unbalance compensation based on optimal tap operation scheduling of three-phase individual controlled step voltage regulators (3ϕSVR) and load ratio control transformer (LRT). In the formulation of the optimization problem, multiple voltage unbalance metrics are comprehensively included. In addition, voltage deviations, network losses, and coordinated tap operations, which are typical issues in distribution systems, are considered. In order to investigate the mutual influence among voltage unbalance and other typical issues, various optimization problems are formulated, and then they are compared by numerical simulations. The results show that the proper operation of 3ϕSVRs and LRT effectively mitigates voltage unbalance. Furthermore, the results also show that voltage unbalances and other typical issues can be improved simultaneously with appropriate formulations. [ABSTRACT FROM AUTHOR]

The current work presents a computationally cost-effective numerical model that successfully simulates a heat pump water heater (HPWH) under typical working conditions of dwellings. The model's main components are a stratified tank and the heat-pump unit. Both systems are coupled, since a good prediction of water temperature is needed to accurately predict the heat-pump performance. Ten thermocouples measured the tank wall temperature. Measurements and simulations were performed under challenging conditions of a heavy stratification. The 190 L tank stratification was successfully modeled employing a 1D model, experimentally adjusted by three tapping cycles, with 6 × 22, 6 × 33, and 3 × 33 L consumptions, covering flowrates of 4 and 6 L/min. Water temperature is obtained with an uncertainty of 2.6 ° C while the heat-pump was ON. A black box model has been used to obtain the heat-pump performance out of the external and condenser temperatures. For the analyzed days, the COP estimation presents an uncertainty of only 5.1%. Finally, an application example is included. It was used to simulate six tapping cycles of the European standard for heat pump water heaters testing (EN 16147). The results show the possibilities for heat-pump manufacturers of applying this calibrated model to predict the performance of HPWHs under different conditions. [ABSTRACT FROM AUTHOR]

This study quantifies the potential of a 4.0 kW air source heat pump (ASHP) unit retrofitted to a 12.0 kW, 1000 L electric boiler coupled to a 1000 L storage tank. A data acquisition system was built to monitor the performance of the electric boiler and the ASHP water heater. The annual electrical energy saving and the load factor reduction from the electric boiler because of the ASHP unit retrofit was 34,805.94 kWh and 0.124. The net present value payback period of the ASHP system was 1.60 years. A Wilcoxon rank sum test was employed to compare both the volumes of hot water and electrical energy consumed by the two systems. Linear regression models of the daily volumes of hot water and electrical energy consumed by both systems were established. The results should be of great value to the management of universities that are considering energy-efficient interventions with a significant return on investment. [ABSTRACT FROM AUTHOR]

Residential water heaters use a substantial amount of electrical energy and contribute to 25% of the energy usage in the residential sector. This raises concern for users in countries with flat rate electricity fees and where fossil fuels are used for electricity generation. Demand side management of tanked water heaters is well suited for energy-focused load reduction strategies. We propose a strategy for providing an electric water heater (EWH) with the optimal temperature planning to reduce the overall electrical energy usage while satisfying the comfort of the user. A probabilistic hot water usage model is used to predict the hot water usage behaviour for the A*-based optimisation algorithm, which accounts for water stratification in the tank. A temperature feedback controller with novel temperature and energy-correcting capabilities provides robustness to prediction errors. Three optimal control strategies are presented and compared to a baseline strategy with the thermostat always on: The first ensures temperature-matched water usages, the second ensures energy-matched water usages, and the third is a variation of the second that provides Legionella prevention. Results were obtained for 77 water heaters, each one simulated for four weeks. The median energy savings for predicted usage were 2.2 % for the temperature-matched strategy, and 9.6 % for both of the energy-matched strategies. We also compare the practical energy savings to the ideal scenario where the optimal scheduling has perfect foreknowledge of hot water usages, and the temperature and energy-matched strategies had a 4.1 and 11.0 percentage point decrease from the ideal energy savings. [ABSTRACT FROM AUTHOR]

Modern households usually have independent energy sources such as wind generators, photovoltaic (PV) panels, and similar green energy production equipment. Experts predict that soon, there will be an increasing number of such prosumers who both produce and consume energy. This process alleviates and reduces the load on large national electricity networks and also contributes to overall energy security. In this paper, a simulation model of a household, which employs a wind generator as its independent source of electricity, is developed. It is expected that this approach will be easily replicated for more complex configurations. The other components of the single prosumer microgrid that will be assessed are the non-shiftable electricity consumption equipment, which is used mainly in households and deployed separately for water heater, with a separate battery to meet the needs of these non-shiftable consumers. The 5-min data intervals for the year of simulation have been used. The characteristics of energy flow according to production and consumption schedules and the capacity of storage equipment have been modelled and simulated. Results disclose that wind turbine production size and buffer battery have a crucial impact on the demand cover factor. [ABSTRACT FROM AUTHOR]

As new grid edge technologies emerge—such as rooftop solar panels, battery storage, and controllable water heaters—quantifying the uncertainties of building load forecasts is becoming more critical. The recent adoption of smart meter infrastructures provided new granular data streams, largely unavailable just ten years ago, that can be utilized to better forecast building-level demand. This paper uses Bayesian Structural Time Series for probabilistic load forecasting at the residential building level to capture uncertainties in forecasting. We use sub-hourly electrical submeter data from 120 residential apartments in Singapore that were part of a behavioral intervention study. The proposed model addresses several fundamental limitations through its flexibility to handle univariate and multivariate scenarios, perform feature selection, and include either static or dynamic effects, as well as its inherent applicability for measurement and verification. We highlight the benefits of this process in three main application areas: (1) Probabilistic Load Forecasting for Apartment-Level Hourly Loads; (2) Submeter Load Forecasting and Segmentation; (3) Measurement and Verification for Behavioral Demand Response. Results show the model achieves a similar performance to ARIMA, another popular time series model, when predicting individual apartment loads, and superior performance when predicting aggregate loads. Furthermore, we show that the model robustly captures uncertainties in the forecasts while providing interpretable results, indicating the importance of, for example, temperature data in its predictions. Finally, our estimates for a behavioral demand response program indicate that it achieved energy savings; however, the confidence interval provided by the probabilistic model is wide. Overall, this probabilistic forecasting model accurately measures uncertainties in forecasts and provides interpretable results that can support building managers and policymakers with the goal of reducing energy use. [ABSTRACT FROM AUTHOR]

The EU aims to become the world's first climate-neutral continent by 2050. In order to meet this target, the integration of high shares of Renewable Energy Sources (RESs) in the energy system is of primary importance. Nevertheless, the large deployment of variable renewable sources such as wind and photovoltaic power will pose important challenges in terms of power management. For this reason, increasing the system flexibility will be crucial to ensure the security of supply in future power systems. This work investigates the flexibility potential obtainable from the diffusion of Demand Response (DR) programmes applied to residential heating for different renewables penetration and power system configuration scenarios. To that end, a bottom-up model for residential heat demand and flexible electric heating systems (heat pumps and electric water heaters) is developed and directly integrated into Dispa-SET, an existing unit commitment optimal dispatch model of the power system. The integrated model is calibrated for the case of Belgium and different simulations are performed varying the penetration and type of residential heating technologies, installed renewables capacity and capacity mix. Results show that, at country level, operational cost could be reduced up to €35 million and curtailment up to 1 TWh per year with 1 million flexible electric heating systems installed. These benefits are significantly reduced when nuclear power plants (non-flexible) are replaced by gas-fired units (flexible) and grow when more renewable capacity is added. Moreover, when the number of flexible heating systems increases, a saturation effect of the flexibility is observed. [ABSTRACT FROM AUTHOR]

In the residential sector, a great part of the electricity goes into heating water by electric water heaters, which results in high CO2 emissions as well as an unprecedented increase in electricity demand leading to an energy crisis. This study offers solar water heaters as a more economical and efficient replacement for electric water heaters. The present study is aimed at investigating the potential for solar water heaters in the subcontinent, especially in India. A feasibility analysis is performed for seven cities in the subcontinent, namely Mumbai, New Delhi, Kolkata, Assam, Gujrat and Madhya Pradesh. Simulated results are based on a solar fraction, equity payback, multiple collectors (one, two or three), horizontal and tilted, type of collector (evacuated tube, glazed and unglazed), electricity saved and greenhouse gas (GHG) emission reduction. The collector's area is made such that it should receive at least 50% of the solar fraction. The range of payback period varies from five to 15 years. The results show Gujrat being the most ideal site for solar water heaters. [ABSTRACT FROM AUTHOR]

In this paper, we present a flexibility estimation mechanism for buildings' thermostatically controlled loads (TCLs) to enable the distribution level consumption of the majority of solar photovoltaic (PV) generation by local building TCLs. The local consumption of PV generation provides several advantages to the grid operation as well as the consumers, such as reducing the stress on the distribution network, minimizing voltage fluctuations and two-way power flows in the distribution network, and reducing the required battery storage capacity for PV integration. This would result in increasing the solar PV generation penetration levels. The aims of this study are twofold. First, spectral (frequency) analyses of solar PV power generation together with the power consumption of multiple building TCLs (such as heating, ventilation, and air conditioning (HVAC) systems, water heaters, and refrigerators) are performed. These analyses define the bandwidth over which these TCLs can operate and also describe the PV generation frequency bandwidth. Such spectral analyses, in frequency domain, can help identify the flexible components of PV generation that can be consumed by the various TCLs through optimal building load utilization. Second, a quadratic optimization problem based on model predictive control is formulated to allow consuming most of the low and medium frequency content of the PV power locally by building TCLs, while maintaining occupants' comfort and TCLs' physical constraints. The solution to the proposed optimization problem is achieved using optimal control strategies. Numerical results show that most of the low and medium frequency content of the PV generation can be consumed locally by building TCLs. The remaining high-frequency content of the PV generation can then be stored/offset using energy storage systems. [ABSTRACT FROM AUTHOR]

Energy poverty can be defined as the inability to pay the bills that are required for maintaining the comfort conditions (usually in winter) in dwellings. The use of energy efficient systems is one way forward to mitigate this problem, with one option being the electrically driven air source heat pump water heater. This paper assesses the performance of a centralised heat pump (200 kW of heating capacity) to meet the space heating demand of block dwellings in Madrid (tier four out of five in winter severity in Spain). Two models have been developed to obtain the following variables: the hourly thermal energy demand and the off-design heat pump performance. The proposed heat pump is driven by a motor with variable rotational speed to modulate the heating capacity in an efficient way. A back-up system is also considered to meet the peak demand. A levelised cost of heating of 92.22 €/MWh is obtained for a middle-level energy efficiency in housing (class E, close to D). Moreover, the following energy-environmental parameters have been achieved: more than 74% share of renewable energy in primary energy and 131.7 g CO2 avoided per kWh met. A reduction of 60% in the heating cost per dwelling is obtained if an energy retrofit is carried out, improving the energy performance class from E to C. These results prove that the proposed technology is among the most promising measures for addressing energy poverty in vulnerable households. [ABSTRACT FROM AUTHOR]

The characteristics of the transcritical CO2 heat pump water heater (HPWH) system are; a lower inlet hot water temperature (Ti-hw) (sometimes this is lower than the water source temperature), and an outlet gas cooler temperature (To-gc) which is affected by the Ti-hw and often lower than the critical temperature. In order to study the effects of the internal heat exchanger (IHX) on the operational performance of the transcritical CO2 HPWH when To-gc is low, a transcritical CO2 water source HPWH experiment platform is established to conduct experimental research and comparative analysis on the operational performance of the transcritical CO2 water source HPWH, with or without IHX. It is found that, if only the coefficient of performance (COP) and heating at the optimal exhaust pressure of the transcritical CO2 water source HPWH were considered, COP and the heating of the non-IHX system would be slightly higher than those of the IHX system at the lower hot water flow and water source temperature, and this increase was not obvious. At the higher hot water flow rate and water source temperature, COP and the heating of the non-IHX system were also higher than those of the IHX system, and the increase was obvious. The experiment results showed that, near the optimal exhaust pressure, the variation range of COP and heating of the IHX system is relatively small, and the system has a relatively high stability. [ABSTRACT FROM AUTHOR]

A household dual source heat pump water heater is proposed to utilize the energy of wastewater and air heat in a bathroom. The heat pump system integrates a wastewater source heat pump (WSHP), air source heat pump (ASHP), and a preheater. This aims at energy saving through recovering the heat of wastewater and ventilation air during the bathing process. The experiment was conducted to verify the feasibility of a dual heat source heat pump water heater system in a bath unit. It is found that the system can achieve an average coefficient of performance (COP) of 4.80 and 4.38 with and without preheater, respectively. At a bath water temperature of 40 °C, a flow rate of 6 L/min, and a room temperature of 26.5 °C, the COP of system can reach 6.08, which shows a significantly promising method for energy saving in-house. [ABSTRACT FROM AUTHOR]

The heat pump water heater (HPWH), as a portion of the eco-friendly technologies using renewable energy, has been applied for years in developed countries. Air-source heat pump water heaters and solar-assisted heat pump water heaters have been widely applied and have become more and more popular because of their comparatively higher energy efficiency and environmental protection. Besides use of the above resources, the heat pump water heater system can also adequately utilize an available water source. In order to study the thermal performance of the water-source heat pump water heater (WSHPWH) system, an experimental prototype using the cyclic heating mode was established. The heating performance of the water-source heat pump water heater system, which was affected by the difference between evaporator water fluxes, was investigated. The water temperature unfavorably exceeded 55 °C when the experimental prototype was used for heating; otherwise, the compressor discharge pressure was close to the maximum discharge temperature, which resulted in system instability. The evaporator water flux allowed this system to function satisfactorily. It is necessary to reduce the exergy loss of the condenser to improve the energy utilization of the system. [ABSTRACT FROM AUTHOR]