Search

This review investigates the role of windcatchers in modern architecture, exploring their optimization through the integration of traditional designs with contemporary technologies. Historically utilized in hot and arid climates for passive cooling, windcatchers offer energy-efficient solutions for improving indoor air quality (IAQ). This study examines the sustainability of traditional windcatcher designs and their relevance in preserving heritage structures. Using advanced tools like computational fluid dynamics (CFD) modeling, modern adaptations of windcatchers can be optimized for urban environments. This review also explores hybrid systems, combining windcatchers with solar chimneys, evaporative cooling, or heat pumps, to enhance performance in low-wind conditions by balancing natural and mechanical ventilation. Additionally, it addresses the role of artificial intelligence (AI) in heritage planning, facilitating the design and integration of windcatchers into contemporary architecture. The findings suggest that windcatchers, combined with modern design strategies and hybrid systems, continue to be viable and sustainable solutions for passive cooling, contributing to energy-efficient and climate-resilient buildings across different environmental and urban contexts. [ABSTRACT FROM AUTHOR]

The purpose of this study is to determine the performances of luffa and greenhouse shading netting (which can be used as alternatives to commercial cellulose pads, that are popular for cooling greenhouses), the contribution of external shading to the evaporative cooling performance, and the energy consumption of the direct evaporative cooler. In this experiment, eight different applications were evaluated: natural ventilation (NV), natural ventilation combined with external shading net (NV + ESN), cellulose pad (CP), cellulose pad combined with external shading net (CP + ESN), luffa pad (LP), luffa pad combined with external shading net (LP + ESN), shading net pad (SNP), and shading net pad combined with external shading net (SNP + ESN). The cooling efficiencies of CP, CP + ESN, LP, LP + ESN, SNP, and SNP + ESN were found to be 37.6%, 45.0%, 38.9%, 41.2%, 24.4%, 29.1%, respectively. Moreover, their cooling capacities were 2.6 kW, 3.0 kW, 2.8 kW, 3.0 kW, 1.7 kW, 2.0 kW, respectively. The system water consumption values were 2.9, 3.1, 2.8, 3.2, 2.4, 2.4 l h−1, respectively. The performance coefficients of the system were determined to be 10.2, 12.1, 11.3, 11.9, 6.6, 7.8. The system's electricity consumption per unit area was 0.15 kWh m−2. As a result of the study, it was determined that commercially used cellulose pads have advantages over luffa and shading net materials. However, luffa pads can be a good alternative to cellulose pads, considering their local availability, initial cost, cooling efficiency, and capacity. [ABSTRACT FROM AUTHOR]

To study the heat and mass transfer characteristics of an evaporative cooler for cooling high-temperature working fluids, an experimental device of the evaporative cooler was built, and a corresponding test system was constructed. Then, the experimental study was carried out based on an orthogonal experimental design, and the law and extent of the influence of water flow in the tube, the spray water flow rate, the inlet water temperature in the tube, and the air flow rate on the heat dissipation, cooling efficiency, and heat and mass transfer coefficients were obtained. The correlation equations of the heat and mass transfer coefficients were obtained by fitting the orthogonal experimental data, and the validity of the correlation equations was confirmed by the verification experiment. [ABSTRACT FROM AUTHOR]

Over the past decade, the integration of desiccant technology with evaporative cooling methods has proven to be highly effective and efficient in providing comfortable indoor environments. The performance of desiccant-based direct evaporative cooling (DEC) systems is strongly influenced by environmental conditions, and their output behavior varies across multiple climatic zones. It is not easy to assess the system performance in numerous climatic zones as it is a time-consuming process. The current study focuses on determining the feasibility of a solid desiccant integrated with a direct evaporative cooler (SDI-DEC) for three different climatic zones of Pakistan: Lahore (hot and humid), Islamabad (hot and semi-humid) and Karachi (moderate and humid). To serve this purpose, a specially designed controlled climate chamber with an integrated air handling unit (AHU) was installed to create multiple environmental conditions artificially. It could also provide global climatic conditions under temperature and absolute humidity ranges of 10 °C to 50 °C and 10 g/kg to 20 g/kg, respectively. The weather conditions of the selected cities were artificially generated in the climate chamber. Based on different operating conditions, such as inlet air temperature, humidity and regeneration temperature, the performance of the system was estimated using performance indicators like COP, dehumidification effectiveness, solar fraction and supply air conditions. Results showed that the maximum temperature achieved from solar collectors was about 70 °C from collectors with an area of 9.5 m2. Moreover, the observations showed that when the regeneration temperature was increased from 60 °C to 80 °C, the COP of the system decreased about 41% in a moderate and humid climate, 28% in a hot and semi-humid environment and 23% in a hot and humid climate. The results revealed that an SDI-DEC system has the potential to overcome the humidity and cooling loads of the multiple climatic scenarios of Pakistan. [ABSTRACT FROM AUTHOR]

There has been considerable research worldwide on desiccant-based air-conditioning during the past 30 years. The rationale for the push for this new research focus has been twofold: (a) the need to provide an alternative to conventional refrigerative air-conditioning systems which rely heavily on fossil fuels as their energy sources, and (b) the need to provide better thermal comfort in air-conditioned spaces in warm to hot and humid climates. A desiccant air-conditioning system consists of several components to cool and dehumidify the air before it is supplied to a conditioned space. Earlier research work has identified the potential advantages of this technology, which include the following: (1) working fluids that do not impact on the ozone layer, (2) reduced electricity consumption, (3) improved indoor air quality, (4) simpler construction and less maintenance, and (5) integral provision of heating and cooling for cold/temperate climates. On the other hand, the authors of this paper identified the following drawbacks: (1) inevitable heating of air while being dehumidified, (2) the need for desiccant regeneration and low thermal COP paradox, (3) limited options for regeneration heat sources, (4) limited options for reliable cooling, and (5) low electrical coefficient of performance (COP). This paper presents a critical review of the energy and thermal comfort performance of solid-desiccant rotor-based air-conditioning systems, and discusses in detail their potential advantages and drawbacks. This critical review found that the drawbacks of the systems outweigh their identified advantages. The main reason for this is the inevitable heating of air while being dehumidified and counterintuitive addition of moisture to air during the evaporative cooling process. During the past 30 years of research and development efforts, no significant innovations have been discovered to resolve these crucial issues. Unless future research and development is directed to find a breakthrough, this technology will have limited commercial application. [ABSTRACT FROM AUTHOR]

In this study, a novel experimental model was proposed, built, and tested to present an efficient and simple method for cooling protective helmets. The system was based on an evaporative cooling technique in which water is used as a coolant sprayed over a canvas covering the outer helmet's surface. A solar fan was provided to enhance the evaporation rate. The experimental results were used with the main laws of heat and mass to evaluate evaporation and heat transfer rates. The proposed system was compared by other two cases, the uncovered dry helmet and the wet-covered one without using the fan. The inner and outer surface temperatures reached were characterized by a good level of stability and by being compatible with human comfort conditions. The addition of the wet cover led to a temperature drop in both the outer and inner surfaces of the helmet by about 9 degrees, and the addition of the fan led to an additional drop of about 5 degrees. There were increases in the cooling rate by 63.3% by adding the wet cover and by 131.7% after adding the fan. The system is characterized by free power consumption and simplicity in implementation. [ABSTRACT FROM AUTHOR]

In light of energy and climate targets, free cooling unlocks a major resource-saving potential compared to refrigeration. To fill the knowledge gap in quantifying this saving potential, we aim to specify the physical and technical limits of cooling tower applications and provide comprehensive data on electricity and water consumption. For this purpose, we distinguish six types of package-type cooling towers: dry, closed wet, open wet, and three types of hybrid systems; defining one generalized system for all types enables comparability. Subsequently, we collect data from 6730 system models of 27 manufacturers, using technical information from data sheets and additional material. The analysis reveals, for example, specific ranges of electricity demand from 0.01 to 0.06 kWel/kWth and highlights influencing factors, including type and operating point. Refrigeration systems would consume approximately ten times more electricity per cooling capacity. Furthermore, the evaluation demonstrates the functional limits, for example, the minimum cooling temperatures. Minimum outlet temperatures using evaporative cooling are up to 16 K lower than for dry cooling. The collected data have crucial implications for designing and optimizing cooling systems, including potential analysis of free cooling and efficiency assessment of cooling towers in operation. [ABSTRACT FROM AUTHOR]

Passive cooling for thermal comfort improvement has received extensive attention for its low energy consumption. However, most of the existing passive cooling technologies require a complex system design and supporting equipment, since they cool the ambient air. Herein, we propose a hybrid evaporative and radiative cooling membrane with a hygroscopic hydrogel sandwiched by two layers of a porous polyethylene aerogel (PEA). The hydrogel implements evaporative cooling. Combining the high solar reflection of PEA and the high infrared emissivity of hydrogel, this hybrid membrane also possesses radiative cooling. In addition, the high infrared transmittance and low thermal conductivity of PEA allow direct heat transfer between the hydrogel and human body, instead of the ambient air. Through comparative experiments and theoretical calculations, it is indicated that the net cooling power delivered by the hybrid membrane to the human body is up to 78.45 W m−2, which is much higher than that of conventional radiative cooling materials. Outdoor demonstration shows that emission below the hybrid membrane can achieve an average sub-ambient temperature drop of 6 °C, with a maximum of 14 °C, showing great potential for passive building cooling and human personal cooling. [ABSTRACT FROM AUTHOR]

Evaporation of a sessile drop is ubiquitous in nature and has many industrial applications. Despite extensive studies over recent decades, a critical issue, i.e., how temperature varies near contact lines, remains elusive. In this work, we report to date the first direct experimental measurement showing the microscopic temperature distribution near contact lines of an evaporating pinned sessile drop. Using a fluorescence-based thermometry, we find that the temperature at the free interface near contact lines varies drastically along the radial direction, engendering a concentric fringe pattern that evolves over the evaporation lifespan. The formation of such fringe patterns is attributed to a combined mechanism of locally enhanced evaporative cooling at the drop edge and the development of interfacial convective vortices due to Bénard-Marangoni instability. We also study the evaporation dynamics at different initial contact angles and find that the characteristics of this fringe pattern vary as the initial contact angle decreases. Our experimental investigation and theoretical analysis in this work reveal insights to the understanding of droplet evaporation dynamics in various heat transfer systems. [ABSTRACT FROM AUTHOR]

An increase in reactive power consumption results in an increase in electricity costs. This negative phenomenon can be prevented by using reactive power compensation methods. One of them is the installation of capacitors. These capacitors are exposed to external conditions, such as temperature and humidity. As a consequence, the aging process occurs. Another negative phenomenon is the corrosion that occurs inside the capacitor as a result of moisture absorption. As a result of this phenomenon, the capacitor can be damaged. One of the symptoms of the ongoing corrosion of the inside of the capacitor is an increase in temperature. Capacitors designed for reactive power compensation operate at mains voltage. They are often placed in a switchgear. For this reason, the use of contact methods of temperature measurement is difficult and dangerous. An alternative is thermographic measurement. Determining the internal temperature of the capacitor by thermographic measurement of the temperature of the case is possible with the use of numerical methods. One of them is FEM (Finite Element Method). The temperature results on the capacitor housing obtained from the simulation work were verified by comparing them with the result of thermographic temperature measurement. Both values differed by 0.2 °C. On the basis of the defined model, the differences between the temperature inside the capacitor housing and the temperature on the capacitor housing were determined by simulation. A simplification was proposed by replacing the cylinder made of layers with a homogeneous cylinder. [ABSTRACT FROM AUTHOR]

Scarcity has made fresh water too economically and socially too valuable to be used by the processing industry without restriction. Wet evaporative cooling cycles offer competitive advantages in terms of CoP compared to other cooling cycles with relatively low cost but requiring extensive quantities of water. Dry cooling, on the other hand, requires large heat-transfer areas, in addition to high power requirements. In this study, a hybrid cycle is proposed for high-end cooling loads of 215 MW. The proposed cycle combines the benefits of phase change to make dry cycles competitive. Furthermore, the proposed cycle also diminishes the extensive use of various chemicals used in wet cooling cycles. The applicable dry bulb temperature range is 25–50 °C. Variations in cooling fluid cold temperature due to ambient conditions are curtailed to a maximum of 2 °C by the proposed cycle. A technoeconomic comparison of the proposed solution to wet evaporative cooling is presented, and the effects are summarized without providing extensive design calculations. ASPEN modules are used design and simulation. [ABSTRACT FROM AUTHOR]

The hybrid indirect evaporative cooling-mechanical vapor compression (IEC-MVC) process is deemed a promising cooling system for hot and humid areas. It possesses the merits of high energy efficiency and strong capability of temperature and humidity control. Herein, we provide an overview of the state-of-the-art investigations over different aspects of the hybrid IEC-MVC process. Firstly, we evaluate the potential of IEC as a pre-cooler and heat-recovery device. Then, we compare the energy efficiency of IEC-MVC with standalone MVC and summarize its long-term energy-saving potential under specific weather conditions. Subsequently, we discuss the economic viability and water consumption of the hybrid process. These studies form a solid foundation for the future installation of the IEC-MVC system. [ABSTRACT FROM AUTHOR]

Preservation of potatoes in a controlled cool environment (i.e., in cold storage) consumes a substantial amount of energy. The specific energy consumption in Indian cold storage has been estimated to be between 9 and 26 kWh/ton/year. In this article, the potential for minimizing the energy consumption in the refrigeration process of cold storage through passive cooling concepts (i.e., roof evaporative cooling and the earth integration of the storage building) was explored. These passive concepts of cooling have shown significant potential for lowering the cooling loads and the energy consumption in different types of buildings. Therefore, a feasibility analysis for a potato storage building, considering the effect of the passive cooling concepts, was conducted for three different climatic conditions (i.e., hot–dry, warm–humid, and composite) in India. The energy saving potentials in the cold storage were assessed by quantifying the thermal energy exchange between the indoor and outdoor environments using the modified admittance method. The effect of heat transfer through the building envelope on total energy consumption was estimated for the building having various sunken volumes (buried depths) without and with roof evaporative cooling. Further, the economic feasibility of adopting passive concepts was assessed in terms of life cycle saving compared to the base case. Results indicate that earth coupling without and with evaporative cooling has substantial potential to reduce the cooling load and can produce significant savings. [ABSTRACT FROM AUTHOR]

As the cooling requirement and the energy prices are increasing rapidly across the world, the need to develop highly efficient cooling equipment is rising as well. Adiabatic cooling employs evaporation to pre-cool the air flowing through a closed-loop coil. This study examines various adiabatic evaporative cooling pads in terms of their pre-cooling potential and advantages over currently available technological solutions through isolating three cross-sectional metal cooling pad shapes (W, Z and Z1). The results of the study suggest that the correlation between Δt↓ and RH↑ is somewhat close in all three cases; however, a slightly higher temperature drop is observed when using a W-shaped metal sheet. Pressure drop variability was negligible under current cooling pad configurations and experimental boundary conditions. Further studies focusing on measurement continuity, longevity and boundary conditions' variability are recommended. [ABSTRACT FROM AUTHOR]

Evaporative cooling is a promising concept to improve proton exchange membrane fuel cells. While the particular concept based on gas diffusion layers (GDLs) modified with hydrophilic lines (HPILs) has recently been demonstrated, there is a lack in the understanding of the mass and heat transport processes. We have developed a 3-D, non-isothermal, macro-homogeneous numerical model focusing on one interface between a HPIL and an anode gas flow channel (AGFC). In the base case model, water evaporates within a thin film adjacent to the interfaces of the HPIL with the AGFC and with the hydrophobic anode GDL. The largest part of the generated water vapor leaves the cell via the AGFC. The transport to the cathode side is shown to be partly limited by the ab-/desorption into/from the membrane. The cooling due to the latent heat has a strong effect on the local evaporation rate. An increase of the mass transfer coefficient for evaporation leads to a transport limited regime inside the MEA while the transport via the AGFC is limited by evaporation kinetics. [ABSTRACT FROM AUTHOR]

In this paper, a plate counter-flow dew-point evaporative cooling system was designed with a nanoporous membrane covered on the surface of the wet channel for enhancement of heat and mass transfer. First, the operating principle of this device and theoretical analysis of nanoporous membrane evaporation were discussed in detail. Then, the impacts of several operating parameters on cooling performance, mainly including inlet air temperature, humidity, velocity, and the effect of utilizing the membrane, were investigated in trials. It was found that the cooling performance can be improved by using membrane significantly. In the dry channel, the maximum temperature decrease can reach 12.5 °C. At a high inlet air temperature, the product air can be dropped to a lower temperature, contributing to a more significant heat transfer process. Lower humidity, on the other hand, resulted in a reduced product air temperature and a lower cooling efficiency. Under the condition of 50% humidity, the wet-bulb efficiency and dew-point efficiency were 1.09 and 0.79, respectively. With the inlet air velocity increasing from 1.5 m/s to 2 m/s, the outlet air temperature would rise, and the wet-bulb efficiency and dew-point efficiency would decrease. To achieve better cooling performance, inlet air velocity ought to be limited to a low speed. [ABSTRACT FROM AUTHOR]

This study investigated an indirect evaporative cooling system (IECS) to control latent heat loss on roof ponds by increasing the evaporation rates on wet fabric membranes. The cooling potential of the proposed system was experimentally tested in a real environment and it was compared against a roof pond and a floating fiber (gunny bags) to provide an efficient model for buildings in hot and humid climates. Dry bulb temperatures (DBT) are presented for four experimental models. Solar irradiance, ambient and indoor dry bulb temperatures, and relative humidity (RH) were measured for seven days in each of the following climate conditions: hot sub-humid (mean DBT 27.3 °C and mean RH 72%), hot humid (mean DBT 27.1 °C and mean RH 81%), and warm sub-humid (mean DBT 25.2 °C and mean RH 68%). There were no significant variations in thermal performance between the examined devices under hot humid conditions; however, the wet fabric device had superior thermal performance under sub-humid conditions when compared to the other IECSs. In the three climatic scenarios where the proposed system was tested, the wet fabric managed to reduce the indoor air temperature by 6.6 °C, 5.3 °C, and 5.1 °C, respectively, as compared to the outdoor air temperatures. [ABSTRACT FROM AUTHOR]

The present study provides insights into the energy-saving potential of a membrane energy recovery ventilator (ERV) for the management of building air-conditioning loads. This study explores direct (DEC), Maisotsenko cycle (MEC) evaporative cooling, and vapor compression (VAC) systems with ERV. Therefore, this study aims to explore possible air-conditioning options in terms of temperature, relative humidity, human thermal comfort, wet bulb effectiveness, energy saving potential, and CO2 emissions. Eight different combinations of the above-mentioned systems are proposed in this study i.e., DEC, MEC, VAC, MEC-VAC, and their possible combinations with and without ERVs. A building was modeled in DesignBuilder and simulated in EnergyPlus. The MEC-VAC system with ERV achieved the highest temperature gradient, wet bulb effectiveness, energy-saving potential, optimum relative humidity, and relatively lower CO2 emissions i.e., 19.7 °C, 2.2, 49%, 48%, and 499.2 kgCO2/kWh, respectively. Thus, this study concludes the hybrid MEC-VAC system with ERV the optimum system for the management of building air-conditioning loads. [ABSTRACT FROM AUTHOR]

Agriculture and agro-based industries consume more energy, mainly derived from fossil fuels. The postharvest storage of agricultural products is crucial for the minimization of postharvest losses, which, throughout the supply chain, are controlled through the provision of optimum temperature and relative humidity conditions. A technoeconomic assessment of nonconventional energy resources (solar, wind and hybrid) in Sudan revealed that solar PV was more suitable in most studied sites for irrigation water pumping, as compared to wind and wind-solar hybrid energy systems [[4]]. [Extracted from the article]

The main objective of this research is to investigate the energy performance enhancement obtained by applying a heat pump to a liquid desiccant and indirect and direct evaporative cooling-assisted 100% outdoor air system (LD-IDECOAS). In conventional LD-IDECOAS operation, the boiler providing regeneration heat to the weak desiccant solution consumes most of the energy. In order to reduce the regeneration energy consumption in the LD-IDECOAS, a heat pump-integrated LD-IDECOAS (HPLD-IDECOAS) is suggested in this research. The heat pump reclaims waste heat from the absorber side of the system, and delivers the reclaimed heat to the regenerator side. Detailed energy simulations for both the LD-IDECOAS and HPLD-IDECOAS were conducted to analyze the energy saving potentiality of the proposed system over the conventional LD-IDECOAS. In both systems, it was assumed that a packed-bed type liquid desiccant unit with an aqueous solution of lithium chloride (LiCl) was used. In the proposed system, a heat pump with R-134a refrigerant was adopted. The results show that the proposed system was able to provide a 33% reduction in annual primary energy consumption compared with the conventional LD-IDECOAS. This significantly enhanced energy performance was mainly obtained through an 83% reduction in the gas energy consumed for regeneration of the desiccant solution in the proposed system by applying the heat pump. [ABSTRACT FROM AUTHOR]

Solar desiccant cooling is widely considered as an attractive replacement for conventional vapor compression air conditioning systems because of its environmental friendliness and energy efficiency advantages. The system performance of solar desiccant cooling strongly depends on the input parameters associated with the system components, such as the solar collector, storage tank and backup heater, etc. In order to understand the implications of different design parameters on the system performance, this study has conducted a parametric analysis on the solar collector area, storage tank volume, and backup heater capacity of a solid solar desiccant cooling system for an office building in Brisbane, Australia climate. In addition, a parametric analysis on the outdoor air humidity ratio control set-point which triggers the operation of the desiccant wheel has also been investigated. The simulation results have shown that either increasing the storage tank volume or increasing solar collector area would result in both increased solar fraction (SF) and system coefficient of performance (COP), while at the same time reduce the backup heater energy consumption. However, the storage tank volume is more sensitive to the system performance than the collector area. From the economic aspect, a storage capacity of 30 m³/576 m² has the lowest life cycle cost (LCC) of $405,954 for the solar subsystem. In addition, 100 kWbackup heater capacity is preferable for the satisfaction of the design regeneration heating coil hot water inlet temperature set-point with relatively low backup heater energy consumption. Moreover, an outdoor air humidity ratio control set-point of 0.008 kgWater/kgDryAir is more reasonable, as it could both guarantee the indoor design conditions and achieve low backup heater energy consumption. [ABSTRACT FROM AUTHOR]

The aim of this study is to determine which of the heat exchangers is characterized by the highest efficiency in different applications. Various types of evaporative air coolers were compared: a typical counter-flow unit, the same unit operating as a heat recovery exchanger, a regenerative unit and a novel, modified regenerative exchanger. The analysis includes comparing the work of evaporative heat exchangers during summer and winter season. The analysis is based on the original mathematical models. The numerical models are based on the modified ε-NTU (number of heat transfer units) method. It was established that selected arrangements of the presented exchangers are characterized by the different efficiency in different air-conditioning applications. The analysis faces the main construction aspects of those evaporative coolers and also compares two above-mentioned devices with modified regenerative air cooler, which can partly operate on cooled outdoor airflow and on the exhaust air from conditioned spaces. This solution can be applied in any climate and it is less dependent on the outdoor conditions. The second part of the study focuses on winter season and the potential of recovering heat with the same exchangers, but with dry working air channels. This allows establishing their total potential of generating energy savings during the annual operation. [ABSTRACT FROM AUTHOR]

The aim of this study is to analyze the operating energy savings of a liquid desiccant and an indirect and direct evaporative cooling-assisted 100% outdoor air system (LD-IDECOAS) for marine applications. The LD-IDECOAS comprises a liquid desiccant (LD) unit and indirect and direct evaporative coolers (IEC and DEC) to meet the target supply air (SA) conditions. In this study, seawater was used as the cooling source and the waste heat reclaimed from the engine was used as the heating source in the proposed system. The operating energy of the LD-IDECOAS was determined based on detailed energy simulations conducted on two cabins with an area of 16.5 m², which was compared to a conventional system. The thermal loads on the cabins were estimated using design weather data under various oceanic climate conditions (normal, extremely hot, and extremely cold climates), by adhering to the ISO-7547 standard. The operating energy consumption of the LD-IDECOAS was calculated by modeling the proposed system with a commercial equation solver program (i.e., EES). The results were then compared to those of a conventional constant air volume (CAV) system. The operating energy consumption of the proposed system was reduced by 57-70% in cooling operations and 39% in heating operations under normal climate conditions. In the extremely hot climate regions, the energy consumed by the proposed system was reduced by 56-63% for cooling applications and 39% for heating applications. [ABSTRACT FROM AUTHOR]

Generally, Central Asia is typical for regions with strong solar radiation and various natural cooling sources. The heat gain from the building envelope accounts for a large part of the cooling load there. Thus, the pipe-embedded envelope is receiving attention as a semi-active system of utilizing natural energy for cooling. In this study, the performance of the pipe-embedded envelope used in Urumqi is numerically investigated. The energy saving potential regarding evaporative cooling and a ground-source heat exchanger (GSHE) is evaluated over a complete summer. The results show that the built-in pipes can reduce 80% of the solar heat gain through windows, with an effectiveness of around 60%. External windows rather than internal windows should be insulated because the air cavity is cool. With respect to the pipe-embedded wall, it becomes a radiant cooling panel absorbing the heat from the room, with an effectiveness around 83%. The seasonal cooling energy is decreased by 25%-50% in a typical office with a pipe-embedded envelope. Offices with a large window-to-wall ratio are acceptable because natural cooling is employed. GSHE performs the best among the selected sources. The effectiveness of evaporative cooling is also satisfactory, with an energy saving rate of 27%. Overall, the pipe-embedded system is suitable for climatic regions like Urumqi. [ABSTRACT FROM AUTHOR]

Air high in humidity leads to uncomfortable conditions and promotes the growth of different fungi and bacteria, which may cause health problems. The control of moisture content in the air using traditional air conditioning techniques is not a suitable option due to large consumption of primary energy and hence emission of greenhouse gases. The evaporative cooling technology is a cost effective and eco-friendly alternative but can provide thermal comfort conditions only under low humidity conditions. However, the evaporative cooling method can be used effectively in conjunction with desiccant dehumidifiers for better control of humidity. Such systems can control the temperature and humidity of the air independently and can effectively utilize the low-grade thermal energy resources. In this paper, the theoretical analysis of desiccant based evaporative cooling systems is carried out for five cities in Saudi Arabia (Jeddah, Jazan, Riyadh, Hail, and Dhahran). It has been observed that the coefficient of performance (COP) of the system varies from 0.275 to 0.476 for different locations. The water removal capacity of the desiccant wheel is at its maximum for the climatic conditions of Jazan and at its minimum for Hail. The effect of climatic conditions of five cities on regeneration temperature, air mass flow rate, and potential of solar energy has been evaluated using RET Screen software. [ABSTRACT FROM AUTHOR]

Evaporative cooling systems using a combination of evaporative pads and extractor fans require greenhouses to be hermetic. The greatest concentration of greenhouses in the world is located in southeast Spain, but these tend not to be hermetic structures and consequently can only rely on fogging systems as evaporative cooling techniques. Evaporative cooling boxes provide an alternative to such systems. Using a low-speed wind tunnel, the present work has compared the performance of this system with four pads of differing geometry and thickness manufactured by two different companies. The results obtained show that the plastic packing in the cooling unit produces a pressure drop of 11.05 Pa at 2 m·s-1, which is between 51.27% and 94.87% lower than that produced by the cellulose pads. This pressure drop was not influenced by increases in the water flow. The evaporative cooling boxes presented greater saturation efficiency at the same flow, namely 82.63%, as opposed to an average figure of 65% for the cellulose pads; and also had a lower specific consumption of water, at around 3.05 L·h-1·m-2·°C-1. Consequently, we conclude that evaporative cooling boxes are a good option for cooling non-hermetic greenhouses such as those most frequently used in the Mediterranean basin. [ABSTRACT FROM AUTHOR]

Irrigated agriculture has the potential to alter regional to global climate significantly. We investigate how irrigation will affect regional climate in the future in an inland irrigation area of northern China, focusing on its effects on heat fluxes and near-surface temperature. Using the Weather Research and Forecasting (WRF) model, we compare simulations among three land cover scenarios: the control scenario (CON), the irrigation scenario (IRR), and the irrigated cropland expansion scenario (ICE). Our results show that the surface energy budgets and temperature are sensitive to changes in the extent and spatial pattern of irrigated land. Conversion to irrigated agriculture at the contemporary scale leads to an increase in annual mean latent heat fluxes of 12.10 W m-2, a decrease in annual mean sensible heat fluxes of 8.85 W m-2, and a decrease in annual mean temperature of 1.3 °C across the study region. Further expansion of irrigated land increases annual mean latent heat fluxes by 18.08 W m-2, decreases annual mean sensible heat fluxes by 12.31 W m-2, and decreases annual mean temperature by 1.7 °C. Our simulated effects of irrigation show that changes in land use management such as irrigation can be an important component of climate change and need to be considered together with greenhouse forcing in climate change assessments. [ABSTRACT FROM AUTHOR]

Modern-day buildings have become the third-largest consumer of energy, after industry and agriculture, and energy consumption in buildings contributes up to 40% of the total energy use in developed countries. The electrical performance of more recently installed PV/T systems does show an overall increase in the annual electrical energy output of 4-12% in comparison with solar PV systems in the same situation. This means that the reposed hybrid energy system offers a higher price per kWh of electricity, possibly due to the inclusion of a diesel generator and battery storage in the system. [Extracted from the article]

Jute is a cheap, eco-friendly, widely available material well-known for its cooling properties. In electric vehicles (EVs), dissipating a huge amount of the heat generated from lithium-ion batteries with an efficient, light, and low-power consumption battery thermal management system (BTMS) is required. In our previous study, jute fibers were proposed and investigated as a novel medium to enhance the cooling efficiency of air-based battery thermal management systems. In this paper, as the first attempt, jute was integrated with a phase change material (PCM) passive cooling system, and the thermal performance of a 50 Ah prismatic battery was studied. Temperature evolution, uniformity, and cooling efficiency were investigated. A comparison between the thermal behavior of the air-based BTMS and PCM-assisted cooling system was performed. The results indicated that adding jute to the BTMS increased the cooling efficiency and especially decreased the temperature development. Furthermore, the temperature difference (ΔT) efficiency was enhanced by 60% when integrating jute with PCM, and temperature uniformity improved by 3% when integrating jute with air-based BTMS. This article compared the integration of jute with active cooling and passive cooling; thus, it shed light on the importance of jute as a novel, eco-friendly, lightweight, cheap, available, and nontoxic material added to two strategies of BTMS. The setup was physically made and experimentally studied for the purpose of BTMS optimization. [ABSTRACT FROM AUTHOR]

The use of the Maisotsenko cycle (M-Cycle) in traditional wet cooling towers (TWCTs) has the potential to reduce the costs of electricity generation by cooling water below the inlet air's wet-bulb temperature. TWCTs cannot provide sufficient cooling capacity for the increasing demand for cooling energy in the power and industrial sectors—especially in hot and wet climates. Due to this fact, an experimental system of an M-Cycle cooling tower (MCT) with parallel counter-flow arrangement fills was constructed in order to provide perspective on the optimal length of dry channels (ldry), thermal performance under different conditions, and pressure drops of the MCT. Results showed that the optimal value of ldry was 2.4 m, and the maximum wet-bulb effectiveness was up to 180%. In addition, the impact of air velocity in wet channels on the pressure drops of the novel fills was also summarized. This study confirms the great potential of using the M-Cycle in TWCTs, and provides a guideline for the industrial application and performance improvement of MCTs. [ABSTRACT FROM AUTHOR]

In the face of increasing demands with regard to the share of renewable energy sources in the energy mix, adsorption chillers are becoming a potentially important part of the energy transition. A key component of this type of equipment is the heat exchanger in the adsorption bed, the design of which affects both heat and mass transfer. This study includes an analysis of the geometry and materials used to manufacture such heat exchangers. The geometry analysis is mainly based on the evaluation of the impact of the different dimensions of the exchanger components on heat and mass transfer in the bed. The second part of the study focuses on material-related issues where the main emphasis is on the analysis of the thermal inertia of the exchanger. The paper analyses the latest research on the design of exchangers in adsorption beds, mainly from 2015–2021. Currently, the commonly used SCP and COP coefficients and various test conditions do not provide sufficient information for comparative analysis of adsorption bed heat exchangers, so the authors propose to introduce a new index for the evaluation of heat exchangers in terms of the effect of the design parameters on the energy efficiency of an adsorption chiller. [ABSTRACT FROM AUTHOR]

Evaporative cooling technology (ECT) has been deemed as an alternative to the conventional vapor-compression air conditioning system for dry climates in recent years due to its simple structure and low operating cost. Generally speaking, the ECT includes two types of different technologies, direct evaporative cooling (DEC) and indirect evaporative cooling (IEC). Both technologies can theoretically reduce the air temperature to the wet-bulb temperature of outdoor air. The major difference between these two technologies is that DEC will introduce extra moisture to the supply air while IEC will not. The enhanced IEC, Maisotsenko-cycle (M-cyle) IEC, can even bring down the air temperature to the dew point temperature. The ECT integrated with solid desiccant systems, i.e., solid desiccant-assisted evaporative cooling technologies (SDECT), could make the technology applicable to a wider range of weather conditions, e.g., weather with high humidity. In this paper, the recent development of various evaporative cooling technologies (ECT), solid desiccant material and the integration of these two technologies, the SDECT, were thoroughly reviewed with respect to their configuration, optimization and desiccant unit improvement. Furthermore, modeling techniques for simulating SDECT with their pros and cons were also reviewed. Potential opportunities and research recommendations were indicated, which include improving the structure and material of M-cycle IEC, developing novel desiccant material and optimizing configuration, water consumption rate and operation strategy of SDECT system. This review paper indicated that the SDECT system could be a potential replacement for the conventional vapor-compressed cooling system and could be applied in hot and humid environments with proper arrangements. [ABSTRACT FROM AUTHOR]

The present study reports the development of a deep learning artificial intelligence (AI) model for predicting the thermal performance of evaporative cooling systems, which are widely used for thermal comfort in different applications. The existing, conventional methods for the analysis of evaporation-assisted cooling systems rely on experimental, mathematical, and empirical approaches in order to determine their thermal performance, which limits their applications in diverse and ambient spatiotemporal conditions. The objective of this research was to predict the thermal performance of three evaporation-assisted air-conditioning systems—direct, indirect, and Maisotsenko evaporative cooling systems—by using an AI approach. For this purpose, a deep learning algorithm was developed and lumped hyperparameters were initially chosen. A correlation analysis was performed prior to the development of the AI model in order to identify the input features that could be the most influential for the prediction efficiency. The deep learning algorithm was then optimized to increase the learning rate and predictive accuracy with respect to experimental data by tuning the hyperparameters, such as by manipulating the activation functions, the number of hidden layers, and the neurons in each layer by incorporating optimizers, including Adam and RMsprop. The results confirmed the applicability of the method with an overall value of R2 = 0.987 between the input data and ground-truth data, showing that the most competent model could predict the designated output features ( T o u t d b , w o u t , and E o u t a i r ). The suggested method is straightforward and was found to be practical in the evaluation of the thermal performance of deployed air conditioning systems under different conditions. The results supported the hypothesis that the proposed deep learning AI algorithm has the potential to explore the feasibility of the three evaporative cooling systems in dynamic ambient conditions for various agricultural and livestock applications. [ABSTRACT FROM AUTHOR]

Natural ventilation, combined with a passive cooling system, can provide significant energy savings in the refrigeration of indoor spaces. The performance of these systems is highly dependent on outdoor climatic conditions. The objective of this study was to analyse the feasibility of a passive, downdraught, evaporative cooling system driven by solar chimneys in different climatic zones by using an experimentally validated simulation tool. This tool combined a ventilation model and a thermal model of the dwelling in which an empirical model of a direct evaporative system made of plastic mesh was implemented. For experimental validation of the combined model, sensors were installed in the dwelling and calibrated in the laboratory. The combined model was applied to Spanish and European cities with different climates. In the simulation, values of cooling energy per volume of air ranging between 0.53 Wh/m3 and 0.79 Wh/m3 were obtained for Alicante (hot climate with moderate humidity) and Madrid (hot and dry climate), respectively. In these locations, medium and high applicability was obtained, respectively, in comparison with Burgos (cold climate with moderate humidity) and Bilbao (cold and humid climate), which were low. The evaluation of the reference building in each location allowed establishing a classification in terms of performance, comfort and applicability for each climate. [ABSTRACT FROM AUTHOR]

The multi-modular converter (MMC) technology is becoming the preferred option for the increased deployment of variable renewable energy sources (RES) into electrical power systems. MMC is known for its reliability and modularity. The fast adjustment of the MMC's active/reactive powers, within a few milliseconds, constitutes a major research challenge. The solution to this challenge will allow accelerated integration of RES, without creating undesirable stability issues in the future power system. This paper presents a variant of model predictive control (MPC) for the grid-connected MMC. MPC is defined using a Laguerre function to reduce the computational burden. This is achieved by reducing the number of parameters of the MMC cost function. The feasibility and effectiveness of the proposed MPC is verified in the real-time digital simulations. Additionally, in this paper, a comparison between an accurate mathematical and real-time simulation (RSCAD) model of an MMC is given. The comparison is done on the level of small-signal disturbance and a Mean Absolute Error (MAE). In the MMC, active and reactive power controls, AC voltage control, output current control, and circulating current controls are implemented, both using PI and MPC controllers. The MPC's performance is tested by the small and large disturbance in active and reactive powers, both in an offline and online simulation. In addition, a sensitivity study is performed for different variables of MPC in the offline simulation. Results obtained in the simulations show good correspondence between mathematical and real-time analytical models during the transient and steady-state conditions with low MAE. The results also indicate the superiority of the proposed MPC with the stable and fast active/reactive power support in real-time simulation. [ABSTRACT FROM AUTHOR]

Heat storage with thermochemical (TC) materials is a promising technology for solar energy storage. In this paper, a solar-driven desiccant evaporative cooling (DEC) system for air-conditioning is proposed, which converts solar heat energy into cooling with built-in daily storage. The system utilises thermochemical heat storage along with the DEC technology in a unique way. Magnesium Chloride (MgCl2·6H2O) has been used, which serves as both a desiccant and a thermochemical heat storage medium. The system has been designed for the subtropical climate of Lahore, Pakistan, for a bedroom with 8 h of cooling requirements during the night. MATLAB has been employed for modelling the system. The simulation results show that 57 kg of magnesium chloride is sufficient to meet 98.8% of cooling demand for the entire month of July at an elevated cooling requirement. It was found that the cooling output of the system increased with increasing heat exchanger effectiveness. The heat exchangers' effectiveness was increased from 0.7 to 0.8, with the solar fraction increased from 70.4% to 82.44%. The cooled air supplied to the building meets the fresh air requirements for proper ventilation. [ABSTRACT FROM AUTHOR]

Gas turbine inlet air-cooling (TIAC) is an established technology for augmenting gas turbine output and efficiency, especially in hot regions. TIAC using evaporative cooling is suitable for hot, dry regions; however, the cooling is limited by the ambient wet-bulb temperature. This study investigates two-stage evaporative TIAC under the harsh weather of Riyadh city. The two-stage evaporative TIAC system consists of indirect and direct evaporative stages. In the indirect stage, air is precooled using water cooled in a cooling tower. In the direct stage, adiabatic saturation cools the air. This investigation was conducted for the GE 7001EA gas turbine model. Thermoflex software was used to simulate the GE 7001EA gas turbine using different TIAC systems including evaporative, two-stage evaporative, hybrid absorption refrigeration evaporative and hybrid vapor-compression refrigeration evaporative cooling systems. Comparisons of different performance parameters of gas turbines were conducted. The added annual profit and payback period were estimated for different TIAC systems. [ABSTRACT FROM AUTHOR]

This study provides insights into the feasibility of a desiccant dehumidification-based Maisotsenko cycle evaporative cooling (M-DAC) system for greenhouse air-conditioning application. Conventional cooling techniques include direct evaporative cooling, refrigeration systems, and passive/active ventilation. which are commonly used in Pakistan; however, they are either not feasible due to their energy cost, or they cannot efficiently provide an optimum microclimate depending on the regions, the growing seasons, and the crop being cultivated. The M-DAC system was therefore proposed and evaluated as an alternative solution for air conditioning to achieve optimum levels of vapor pressure deficit (VPD) for greenhouse crop production. The objective of this study was to investigate the thermodynamic performance of the proposed system from the viewpoints of the temperature gradient, relative humidity level, VPD, and dehumidification gradient. Results showed that the standalone desiccant air-conditioning (DAC) system created maximum dehumidification gradient (i.e., 16.8 g/kg) and maximum temperature gradient (i.e., 8.4 °C) at 24.3 g/kg and 38.6 °C ambient air conditions, respectively. The DAC coupled with a heat exchanger (DAC+HX) created a temperature gradient nearly equal to ambient air conditions, which is not in the optimal range for greenhouse growing conditions. Analysis of the M-DAC system showed that a maximum air temperature gradient, i.e., 21.9 °C at 39.2 °C ambient air condition, can be achieved, and is considered optimal for most greenhouse crops. Results were validated with two microclimate models (OptDeg and Cft) by taking into account the optimality of VPD at different growth stages of tomato plants. This study suggests that the M-DAC system is a feasible method to be considered as an efficient solution for greenhouse air-conditioning under the climate conditions of Multan (Pakistan). [ABSTRACT FROM AUTHOR]

The article deals with the study on the efficiency of units for porous ammonium nitrate production. The ways which increase the effective implementation of energy resources are determined by including the ejector recycling module, heat and mass exchangers that utilize principles of regenerative indirect evaporative cooling, and the sub-atmospheric inverse Brayton cycle. Mixed exergy analysis evaluates all flows of the system contour as those of the same value. The target parameter for determining the efficiency of both systems is the ratio of the unit's productivity to the exergy expenditures to produce the unit mass of the product. As a result, it is found that the mentioned devices and units enable to increase the efficiency of the basic scheme by 87%. [ABSTRACT FROM AUTHOR]

Solar photovoltaic (PV) applications are gaining a great interest worldwide and dominating the renewable energy sector. However, the solar PV panels' performance is reduced significantly with the increase in their operating temperature, resulting in a substantial loss of energy production and poor economic scenarios. This research contributes to overcoming the PV performance degradation due to the temperature rise. This work involves experimental and theoretical studies on cooling of PV panels using the evaporative cooling (EC) principle. A new EC design to cool the bottom surface of a PV panel was proposed, fabricated, tested, and modeled. A series of experimentation readings under real conditions showed the effectiveness of the method. A steady state heat and mass transfer model was implemented and compared with the experimental data. Fair agreement between the results of the modelling and experimental work was observed. It was found that the temperature of the PV panel can be decreased by 10 °C and the power improvement achieved was 5%. Moreover, the EC helps to stabilize the panels' temperature fluctuation, which results in a better regulation of electrical power output and reduces the uncertainty associated with solar PV systems. [ABSTRACT FROM AUTHOR]

A thermal model is proposed to analyze the performance of an indirect solar dryer (ISD) with latent heat storage using phase change material (PCM). The estimations are compared with experimental data presented in the scientific literature taken in real conditions. The validated thermal model is used in order to address a comprehensive analysis of the performance of the ISDs under the same operation conditions, the model is able to estimate the temperatures of glass cover, absorber plate, PCM, useful heat, thermal and storage efficiencies, and variables that are difficult to measure experimentally such as liquid fraction, heat losses, and accumulated energy of the ISDs. Three study cases are considered: Case 1 consists of two collectors with and without alternating nocturnal and diurnal operation (benchmarking case). Case 2 and 3 consist in a unique collector operating continuously for 24 h with PCM and without PCM, respectively. It was determined that the use of PCM in ISD increased the night thermal performance and extended the operational time of the system. On the other hand, results indicate that the use of two alternating collectors presents similar discharge behavior to using one collector with PCM operating continuously. Concerning the overall thermal performance, cases 1, 2, and 3 obtained thermal efficiencies of 20%, 28%, and 24%, respectively. [ABSTRACT FROM AUTHOR]

This paper aims to conduct a parametric study for five gas turbine cycles (namely, simple, heat exchanged, free turbine and simple cycle, evaporative, and humidified) using a CO2-argon-steam-oxyfuel (CARSOXY) mixture as a working fluid to identify their optimal working conditions with respect to cycle efficiency and specific work output. The performance of the five cycles using CARSOXY is estimated for wet and dry compression, and a cycle is suggested for each range of working conditions. The results of this paper are based on MATLAB codes, which have been developed to conduct the cycle analysis for CARSOXY gas turbines, assuming a stoichiometric condition with an equivalence ratio of 1.0. Analyses are based on the higher heating value (HHV) of methane as fuel. This paper also identifies domains of operating conditions for each cycle, where the efficiency of CARSOXY cycles can be increased by up to 12% compared to air-driven cycles. The CARSOXY heat exchanged cycle has the highest efficiency among the other CARSOXY cycles in the compressor pressure ratio domain of 2–3 and 6–10, whereas, at 3–6, the humidified cycle has the highest efficiency. The evaporative cycle has intermediate efficiency values, while the simple cycle and the free turbine-simple cycle have the lowest efficiencies amongst the five cycles. Additionally, a 10% increase in the cycle efficiency can be theoretically achieved by using the newly suggested CARSOXY blend that has the molar fractions of 47% argon, 10% carbon dioxide, 10% H2O, and 33% oxyfuel at low compressor inlet temperatures, thus theoretically enabling the use of carbon capture technologies. [ABSTRACT FROM AUTHOR]

Pre-cooling of inlet air using evaporative cooling is an effective approach to enhance the performance of air-cooled condensers in air conditioning applications. Ultrasonic mist generators have emerged as a promising alternative to conventional evaporative cooling systems based on cooling pads or spray cooling. This paper presents the developed numerical model of an ultrasonic mist generator for the evaporative pre-cooling of the inlet air of the condenser in air conditioning applications. The model was validated against the experimental data obtained in a wind tunnel experimental facility. A parametric analysis including some physical variables involved in the cooling process was carried out, including the main axial air velocity, the injection air velocity and the water mass flow rate of atomized water. The dimensionless groups water-to-air mass flow and air-to-air mass flow ratios were found to most affect the average evaporative cooling efficiency. A maximum value of 0.654 was found for the studied conditions. The optimization analysis carried out shows that the operational ranges leading to the best overall performance are 5 × 10 − 4 ≤ m ˙ w / m ˙ a T ≤ 0.002 and 0.035 ≤ m ˙ a i / m ˙ a T ≤ 0.05 . Under these conditions, there is a better distribution of the water mist throughout the control section and a more homogeneous and effective evaporative cooling process. [ABSTRACT FROM AUTHOR]

A windcatcher is a wind-driven natural ventilation system that catches the prevailing wind to bring fresh airflow into the building and remove existing stale air. This technology recently regained attention and is increasingly being employed in buildings for passive ventilation and cooling. The combination of windcatchers and evaporative cooling has the potential to reduce the amount of energy required to ventilate and cool a greenhouse in warm and hot climates. This study examined a greenhouse incorporated with a passive downdraught evaporative cooling windcatcher (PDEC-WC) system using Computational Fluid Dynamics (CFD), validated with experimental data. Different hot ambient conditions of temperature (30–45 °C) and relative humidity (15–45%) were considered. The study explored the influence of different spray heights, layouts, cone angles and mass flow rates on indoor temperature and humidity. The average error between measurements and simulated results was 5.4% for the greenhouse model and 4.6% for the evaporative spray model. Based on the results and set conditions, the system was able to reduce the air temperature by up to 13.3 °C and to increase relative humidity by 54%. The study also assessed the influence of neighbouring structures or other greenhouses that influence the flow distribution at the ventilation openings. The study showed that the windcatcher ventilation system provided higher airflow rates as compared to cross-flow ventilation when other structures surrounded the greenhouse. [ABSTRACT FROM AUTHOR]

The present study considers evaporative cooling and desiccant unit-based air-conditioning (AC) options for livestock AC application. In this regard, proposed systems are investigated by means of experiments and thermodynamic investigations. Air-conditioning requirements for animals are theoretically investigated and temperature-humidity index (THI) is estimated. A lab-scale heat mass exchanger based on the Maisotsenko-cycle evaporative cooling conception (MEC) is set up and its performance is evaluated at different ambient air conditions. In addition, a desiccant-based air-conditioning (DAC) unit is thermodynamically evaluated using a steady-state model available in the literature. The study focuses on the ambient conditions of Multan which is the 5th largest city of Pakistan and is assumed to be a typical hot city of southern Punjab. The study proposed three kinds of AC combination i.e., (i) stand-alone MEC, (ii) stand-alone desiccant AC, and (iii) M-cycle based desiccant AC systems. Wet bulb effectiveness of the stand-alone MEC unit resulted in being from 64% to 78% whereas the coefficient of performance for stand-alone desiccant AC and M-cycle based desiccant AC system was found to be 0.51 and 0.62, respectively. Results showed that the stand-alone MEC and M-cycle based desiccant AC systems can achieve the animals' thermal comfort for the months of March to June and March to September, respectively, whereas, stand-alone desiccant AC is not found to be feasible in any month. In addition, the ambient situations of winter months (October to February) are already within the range of animal thermal comfort. [ABSTRACT FROM AUTHOR]

The condensate on the surface of the minichannel heat exchanger generated during air cooling substantially reduces the heat transfer performance as it works as an evaporator in the air-conditioning system. This has received much attention in scientific communities. In this paper, the effect of operating parameters on the heat transfer performance of a minichannel heat exchanger (MHE) is investigated under an evaporator working condition. An experimental MHE test system is developed for this purpose, and extensive experimental studies are conducted under a wide range of working conditions using the water-cooling method. The inlet air temperature shows a large effect on the overall heat transfer coefficient, while the inlet air relative humidity shows a large effect on the condensate aggregation rate. The airside heat transfer coefficient increases from 66 to 81 W/(m2·K) when the inlet air temperature increases from 30 to 35 °C. While the condensate aggregation rate on the MHE surface increases by up to 1.8 times when the relative humidity increases from 50% to 70%. The optimal air velocity, 2.5 m/s, is identified in terms of the heat transfer rate and airside heat transfer coefficient of the MHE. It is also found that the heat transfer rate and overall heat transfer coefficient increase as the air velocity increases from 1.5 to 2.5 m/s and decreases above 2.5 m/s. Furthermore, a large amount of condensate accumulates on the MHE surface lowering the MHE heat transfer. The inclined installation angle of the MHE in the wind tunnel effectively enhances heat transfer performance on the MHE surface. The experimental results provide useful information for reducing condensate accumulation and enhancing microchannel heat transfer. [ABSTRACT FROM AUTHOR]

This work focuses on the demand response (DR) participation using the energy storage system (ESS). A probabilistic Gaussian mixture model based on market operating results Monte, Carlo Simulation (MCS), is required to respond to an urgent DR signal. However, there is considerable uncertainty in DR forecasting, which occasionally fails to predict DR events. Because this failure is attributable to the intermittency of the DR signals, a non-cooperative game model that is useful for decision-making on DR participation is proposed. The game is conducted with each player holding a surplus of energy but incomplete information. Consequently, each player can share unused electricity during DR events, engaging in indirect energy trading (IET) under a non-cooperative game framework. The results of the game, the Nash equilibrium (N.E.), are verified using a case study with relevant analytical data from the campus of Gwangju Institute of Science and Technology (GIST) in Korea. The results of the case study show that IET is useful in mitigating the uncertainty of the DR program. [ABSTRACT FROM AUTHOR]

This study investigated the annual energy saving potential and system performance of two different evaporative cooling-based liquid desiccant and evaporative cooling-assisted air conditioning systems. One system used an indirect and direct evaporative cooler with a two-stage package to match the target supply air point. The other was equipped with a single-stage, packaged dew-point evaporative cooler that used a portion of the process air, which had been dehumidified in advance. Systems installed with the two evaporative coolers were compared to determine which one was more energy efficient and which one could provide better thermal comfort for building occupants in a given climate zone, using detailed simulation data. The detailed energy consumption data of these two systems were estimated using an engineering equation solver with each component model. The results showed that the liquid desiccant and dew-point evaporative-cooler-assisted 100% outdoor air system (LDEOAS) resulted in approximately 34% more annual primary energy consumption than that of the liquid desiccant and the indirect and direct evaporative-cooler-assisted 100% outdoor air system (LDIDECOAS). However, the LDEOAS could provide drier and cooler supply air, compared with the LDIDECOAS. In conclusion, LDIDECOAS has a higher energy saving potential than LDEOAS, with an acceptable level of thermal comfort. [ABSTRACT FROM AUTHOR]

The possibility of implementing the innovative multi-disc sorption bed combined with the heat exchanger into the adsorption cooling technology is investigated experimentally and numerically in the paper. The developed in-house sorption model incorporated into the commercial computational fluid dynamics (CFD) code was applied within the analysis. The research allowed to define the design parameters of the proposed type of the sorption bed and correlate them with basic factors influencing the performance of the sorption bed and its dimensions. The designed multi-disc sorption bed is characterized by great scalability and allows to significantly expand the potential installation sites of the adsorption chillers. [ABSTRACT FROM AUTHOR]

An increased awareness of the impacts of synthetic refrigerants on the environment has prompted the refrigeration industry and researchers worldwide to seek better alternatives in terms of technical, economic and environmental performance. CO2 refrigerant, also known as R744, has re-emerged as a potential alternative to existing refrigerants with its zero ozone depletion potential (ODP) and impressively low global warming potential (GWP). A refrigeration system utilising this refrigerant, however, suffers performance degradation when it operates in warm or hot climatic regions due to its inevitable operation in the supercritical region. In addition, the CO2 refrigerant properties necessitate the need for components designed to withstand very high operating pressures. These challenges have not been let unnoticed; related industries and researchers are actively involved in research and development of various components and systems which in turn encourages increased applications of these systems. In this paper, a comprehensive review of CO2 refrigeration systems and the state of the art of the technology and its applications in various industries is presented. In particular, the paper reviews recent research and developments on various aspects of CO2 systems including cycle modifications, exergy analysis of the systems, system modelling, transcritical operation consideration and various existing and potential applications. [ABSTRACT FROM AUTHOR]