Search

It is well known that the existing horizontal-well-drilling and hydraulic fracturing technology used to achieve large-scale, cost-effective production from immature to low–moderate-maturity continental shale in China, where the organic matter mainly exists in solid form, is fairly ineffective. To overcome the obstacles, in situ conversion technology seems feasible, while implementing it in the target layer along with estimating the amount of expected recoverable hydrocarbon in such shale formations seems difficult. This is because there are no guidelines for choosing the most appropriate method and selecting relevant key parameters for this purpose. Hence, based on thermal simulation experiments during the in situ conversion of crude oil from the Triassic Chang 73 Formation in the Ordos Basin and the Cretaceous Nenjiang Formation in the Songliao Basin, this deficiency in knowledge was addressed. First, relationships between the in situ-converted total organic carbon (TOC) content and the vitrinite reflectance (Ro) of the shales and between the residual oil volume and the hydrocarbon yield were established. Second, the yields of residual oil and in situ-converted hydrocarbon were measured, revealing their sensitivity to fluid pressure and crude oil density. In addition, a model was proposed to estimate the amount of in situ-converted hydrocarbon based on TOC, hydrocarbon generation potential, Ro, residual oil volume, fluid pressure, and crude oil density. Finally, a method was established to determine key parameters of the final hydrocarbon yield from immature to low–moderate-maturity organic material during in situ conversion in shales. Following the procedure outlined in this paper, the estimated recoverable in situ-converted oil in the shales of the Nenjiang Formation in the Songliao Basin was estimated to be approximately 292 × 108 tons, along with 18.5 × 1012 cubic meters of natural gas, in an area of approximately 8 × 104 square kilometers. Collectively, the method developed in this study is independent of the organic matter type and other geological and/or petrophysical properties of the formation and can be applied to other areas globally where there are no available in situ conversion thermal simulation experimental data. [ABSTRACT FROM AUTHOR]

Affected by Tianshan uplift, the southern Junggar Basin has experienced multi-stage tectonic movements and formed many large-scale anticlines with zonal distribution. The key to hydrocarbon exploration is to accurately implement anticline traps. This paper is guided by the fault-related folds theory to tectonically interpret several seismic profiles in the southern Junggar Basin and then summarize the anticline types and their hydrocarbon accumulation characteristics. This paper showed that the southern Junggar Basin has a tectonic assemblage pattern of "multi-detachment layers and multi-phase superposition". According to the superimposed shape of the anticlines, they could be divided into overthrust anticlines, compound anticlines and multiple superimposed anticlines, and the horizontal and vertical positions of the different types of anticlines are different. The hydrocarbon accumulating characteristics of the different types of anticlines are shown to be different. The highs of the overthrust anticlines and compound anticlines are stable, and the degree of exploration is relatively high. Although the degree of exploration of multiple overlapping anticlines is low, multiple layers can be exploited simultaneously in the process of oil development, with great hydrocarbon potential. The characteristics of hydrocarbon accumulation in the southern Junggar Basin are discussed in order to provide guidance for efficient hydrocarbon exploration. [ABSTRACT FROM AUTHOR]

Transitional shale gas, rich in resources, is expected to be a practical contributor to the increase in shale gas reserves and production in China. Its exploration prospect has been demonstrated by several wells in the Daning-Jixian block on the eastern margin of the Ordos Basin. In this paper, the Lower Permian Shanxi Formation (P1s) and Taiyuan Formation (P1t) in the eastern margin of Ordos Basin were compared for organic geochemical parameters, revealing that the overflow fan + lagoon combination (OLC) of the third sub-member of the second member of Shanxi Formation (P1s23) and the marine + lagoon combination (MLC) of the first member of Taiyuan Formation (P1t1) are the most favorable shale gas intervals. The two intervals were comparatively analyzed with respect to mineral composition, brittleness, caprocks, and preservation conditions. It is found that the OLC of P1s23 has a similar porosity to and much lower permeability than the MLC of P1t1 (or MLC1) and a BET surface area of 10–15 m2/g, which is smaller than the MLC1 (15–20 m2/g). Moreover, OLC has a brittle mineral content equivalent to MLC1 but a brittleness index of 33.73–62.36 (avg. 49.86), smaller than MLC1 (53.34–58.27, or avg. 55.85). OLC contains sandstones at both the roof and floor, with a higher permeability than shale in the interval, which cannot serve as good physical seals. In contrast, MLC1 contains limestones with lower permeability at the roof and floor, which, together with the overlying coal seams, have hydrocarbon generation capacity and can physically seal the MLC1 shale but also fill it with hydrocarbons, making MLC1 have higher gas content and superior for shale gas exploration than the OLC shale. Due to the multi-lithologies developed in transitional facies, besides the organic matter enrichment, and reservoir characteristics, it is necessary to find a suitable lithological combination to ensure the gas in shale can be better preserved and retained. [ABSTRACT FROM AUTHOR]

In the process of diagenesis and burial of sedimentary basins, basin fluid activities participate in the process of hydrocarbon accumulation and metal mineralization. Understanding the evolution of basin fluid is of great significance in revealing the related hydrocarbon accumulation and mineralization. Paleo-reservoirs are closely associated with Carlin-type gold deposits in the Nanpanjiang-Youjiang Basin, South China. Calcite, the fluid activity product, is closely related to bitumen and gold-bearing pyrite. By integrating petrographic, cathode luminescence, and fluid inclusion analysis, as well as the relevant chronological results of predecessors, this paper attempts to establish the relationship between fluid evolution, hydrocarbon accumulation, and gold mineralization. Two types of calcite (black/gray and white) developed in the Banqi-Yata-Laizishan area, the Nanpanjiang-Youjiang Basin. Black/gray calcite is symbiotic with bitumen and features dark red colors in cathode luminescence. Many hydrocarbon inclusions developed along with fluid inclusion analysis at low homogenization temperatures (65.7~173.1 °C). Combining the previously reported U-Pb ages (~250–230 Ma) of this kind of calcite with some geochemistry data on the associated reservoir and gold deposit, this calcite records the consecutive hydrocarbon accumulation and Carlin-type gold mineralization from the Late Permian to the Late Triassic periods controlled by Indosinian tectonic movement. The white calcite featuring bright red in cathodoluminescence is symbiotic with gold-bearing pyrite and realgar, and the associated fluid inclusions have high homogenization temperatures (128.2~299.9 °C). Combined with regional tectonic background and isotopic chronology (~140–106 Ma), it seems to record the early Cretaceous Carlin-type gold mineralization controlled by the subduction of the paleo-Pacific plate in the late Yanshanian period. [ABSTRACT FROM AUTHOR]

The distribution characteristics and main controlling factors of hydrocarbon phases in deep strata from petroliferous basins are important for the evaluation of oil–gas resources and decision-making regarding exploration. The distribution characteristics and controlling factors of the Ordovician hydrocarbon phases are systematically analyzed in the Tazhong I block, Tarim Basin, NW China. The results show that the Ordovician reservoirs in the Tazhong I block are characterized as multi-phase reservoirs with a lateral co-existence of condensates, normal oil reservoirs, and heavy oil reservoirs. From east to west, gas-rich in the fault belt and oil-rich in the platform area are presented. Meanwhile, there are regular variations in the geochemical characteristics of the Ordovician hydrocarbon, showing decreasing trends in the gas/oil ratio (GOR), wax contents, dryness coefficients, methane contents, and methane carbonate isotope values (δ13C1) and an increasing trend in oil densities. Because the same Cambrian–Lower Ordovician source for the Ordovician hydrocarbon is observed in the Tazhong I block, the regular variations in the hydrocarbon phases and geochemical characteristics can be interpreted as records of gas invasion, biodegradation, multi-stage filling, thermal cracking, and thermochemical sulfate reduction (TSR) rather than controlled by the source rock organofacies. This indicated that different kinds of secondary processes for a diversity of the hydrocarbon phase can appear in one region. Our re-construction of the Ordovician hydrocarbon accumulation model in the Tazhong I block encourages future exploration to target gas reservoirs in the fault belt and oil reservoirs in the platform area. [ABSTRACT FROM AUTHOR]

Geothermal energy is one of the cleanest sources of energy which is gaining importance as an alternative to hydrocarbons. Geothermal energy reserves in China are enormous and it has a huge potential for exploitation and utilization. However, the development of the geothermal industry in China lags far behind other renewable energy sources because of the lack of fiscal and taxation policy support. In this paper, we adopt the system dynamics method and use the causal loop diagram to explore the development mechanism of fiscal and taxation policies in the geothermal industry. The effect of the fiscal and taxation policy on the development of the geothermal industry is analyzed. In order to promote sustainable development of the geothermal industry in China, the government should pay more attention to subsidies for the geothermal industry in the life-cycle stage of the geothermal industry. Furthermore, a plan is necessary to provide a reasonable system of fiscal and taxation policies. [ABSTRACT FROM AUTHOR]

In order to study the distribution pattern of hydrocarbons in the shallow layer of the slope area outside of the source in the hydrocarbon-bearing basin, we built a method to predict the favorable site of the fault that adjusts hydrocarbon to the shallow layer in the slope area outside of the source based on the investigation of the mechanism of hydrocarbon adjustment along a conduit fault to a shallow layer. The predicted favorable site is found to be the overlapping area of three sites: the locations of the sand carrier with a lateral supply of hydrocarbon, the transport sites of conduit faults, and the hydrocarbon leakage parts of overlying regional mudstone seal rock. We applied the method in a case study of the favorable sites of the Zhaobei Fault that adjust the hydrocarbon from the lower sub-member within the first member of Shahejie Formation (Es1L) to the shallow Guantao Formation in the Qikou Sag of Bohai Bay Basin. Our prediction shows that the favorable sites are mostly located in the middle part of the Zhaobei Fault with very limited distribution in the east, which are conducive to the oil and gas supplied by the underlying sand carrier in the Es1L Formation to convergence and accumulation in the shallow Guantao Formation. This result is consistent with the distribution of the hydrocarbon in the Guantao Formation located in the middle parts of the Zhaobei Fault, proving that this method is feasible for the prediction of the favorable sites of the fault that adjust hydrocarbon to the shallow layer in the slope area outside of source. [ABSTRACT FROM AUTHOR]

To understand hydrocarbon migration in terms of the mechanisms, accumulations and exploration targets, it is essential to correctly identify and characterize the carrier systems that control fluid-migration history and oil/gas reservoir formation. The Yinggehai Basin in China is an important area for natural gas exploration and production. However, due to the argillaceous sand sedimentary environment and the absence of faults from the Neogene thermal subsidence period, traditional migration pathways are absent in the Yinggehai Basin, posing significant challenges to target evaluation in this area. Exploration shows that most of the existing gas reservoirs are associated with vertical migration. In this work, coherence cube and curvature seismic techniques are used in the central diapir zone of the Yinggehai Basin to identify diapir-associated fractures and regional stress. Together with geological analysis, two categories of carrier system are discussed in detail to explain the complex migration and accumulation patterns that have puzzled the area. Diapirs have five evolutionary phases, i.e., pressurization, piercing, equilibrium, release and collapse, which have different fracture development patterns, leading to different mechanisms of hydrocarbon migration and accumulation. The carbon isotopes of gaseous hydrocarbons in DF shallow layers and mid-deep layers have an inverted order distribution, indicating mixed accumulation with different maturity, whereas in the mid-deep layers of the diapir-affected areas, there is a single accumulation with low maturity. Early diapiric activity allowed the natural gas produced from deep source rocks to migrate upward along the diapiric carrier system and accumulate in suitable traps to form gas reservoirs. For regional-stress related fractures, the gradual loss of overpressure and fluids from deep to shallow in high-pressure fractures results in the gas accumulation time of deep traps in the regional stress-related carrier system being relatively late and the gas accumulation time of shallow traps being relatively early. [ABSTRACT FROM AUTHOR]

Organic matter (OM) type critically controls the hydrocarbon generation potential and organic pore development in black shales. However, maceral variation in lacustrine shales and its control on hydrocarbon generation potential and organic pore development are not yet well understood. In this study, 15 Chang 7 Member shale samples of the Yanchang Formation, Ordos Basin, were investigated with organic petrography, Rock-Eval pyrolysis, and a scanning electron microscope to study the maceral composition, hydrocarbon generation potential, and organic pores in this black shale succession. The results show that the studied shales are in the oil window (Ro~0.70%). OM belongs to Type I and Type III kerogen, as demonstrated by Rock-Eval pyrolysis. Macerals in the Chang 7 Member shales are composed of amorphous OM, alginite, sporinite, liptodetrinite, vitrinite, inertinite, and solid bitumen. Amorphous OM and alginite are major hydrocarbon-generating macerals, and their content determines the hydrocarbon potential of shales. Secondary organic pores were not observed in the studied Chang 7 Member shales due to either a low thermal maturity or a dominance of terrigenous OM. Maceral variation can affect the reliability of using Rock-Eval Tmax as a thermal maturity indicator. This study provides important insights into maceral control on hydrocarbon generation and organic pore development in black shales, calling for a critical evaluation of OM in black shale successions with organic petrography. [ABSTRACT FROM AUTHOR]

Shale oil resources are important supplements for the gradually decreasing oil production from conventional reservoirs. Although the exploitation and development of shale oil have achieved considerable progress in the last decade, the commercial extraction of hydrocarbons from shales is still difficult, especially in the lacustrine sedimentary basins of China. One of the key points controlling the successful extraction of hydrocarbons from shale systems is the understanding of the occurrence mechanism of shale oil. This study comprehensively summarizes the theories and techniques to characterize oil occurrence state, occurrence space, oil content, and oil movability in shale systems. Sophisticated instruments, such as high-resolution scanning electron microscopy and high-energy ray imaging, were utilized to qualitatively analyze the pore networks of shales. Advanced physical experiments and numerical simulation techniques, including step-by-step rock pyrolysis, solvent extraction, and NMR, were introduced to characterize shale oil adsorption and movability. By the comparative analysis of the occurrence space, it is found that the image observation technique especially focuses on concentrated pores, such as organic matter-hosted pores. The fluid injection technology yields particular pore size information, which should be calibrated using other information. The 3D digital core, demonstrating the spatial distribution of minerals and pores, is an effective input for shale oil flow simulation. Geological controls analysis about oil retention in organic-rich shales has found that the inorganic matter pores and fractures are probably the "sweet spot" of shale oil, due to the low oil adsorption and high light hydrocarbons content. Many physical experiments measure the total free oil content but neglect the hydrocarbon–rock interaction and the sequential migration of hydrocarbon compounds. Thus, micro-scaled experiments measuring the hydrocarbon adhesion forces are needed to uncover the occurrence mechanism of shale oil in the future. [ABSTRACT FROM AUTHOR]

The Wumaying buried hill experienced multi-stage tectonic movements, which resulted in a complicated and unclear nature of the hydrocarbon accumulation process. To solve these problems, in this study—based on the structural evolution and burial–thermal history of the strata, using petrology, fluid inclusion microthermometry, geochemical analysis of oil and gas, Laser Raman spectrum, and fluorescence spectrum—the history of hydrocarbon charging was revealed, and the differences in hydrocarbon charging of different wells was clarified. The results indicate that the only source for Permian oil and gas reservoirs are Carboniferous–Permian coal-measure source rocks in the Wumaying buried hill. There are three periods of hydrocarbon charging. Under the channeling of faults and micro cracks, low-mature oil and gas accumulation was formed in the first period, and the accumulation time was 112–93 Ma. In the late Cretaceous, a large-scale uplift exposed and damaged the reservoirs, and part of the petroleum was converted into bitumen. In the middle–late Paleogene, the subsidence of strata caused the coal-measure to expel mature oil and gas, and the accumulation time of mature oil and gas was 34–24 Ma. Since the Neogene, natural gas and high-mature oil have been expelled due to the large subsidence entering the reservoir under the channeling of active faults; the accumulation time was 11–0 Ma. The microfractures of Permian reservoirs in the Wumaying buried hill are the main storage spaces of hydrocarbons, and the fractured reservoirs should be explored in the future. The first period of charging was too small and the second period was large enough in the WS1 well, resulting in only a late period of charging in this well. [ABSTRACT FROM AUTHOR]

Deeply buried sandstones in the Jurassic, Toutunhe Formation, are a crucial exploration target in the Junggar Basin, NW China, whereas, reservoir-forming process of sandstones in the Toutunhe Formation remain unknown. Focused on the tight sandstone of the Toutunhe Formation, the impacts of diagenesis and hydrocarbon charging on sandstone reservoir-forming process were clarified based on the comprehensive analysis of sedimentary characteristics, petrography, petrophysical characteristics, and fluid inclusion analysis. Three diagenetic facies developed in the Toutunhe sandstone reservoirs, including carbonate cemented facies (CCF), matrix-caused tightly compacted facies (MTCF), and weakly diagenetic reformed facies (WDF). Except the WDF, the CCF and the MTCF entered the tight state in 18 Ma and 9 Ma, respectively. There was only one hydrocarbon emplacing event in sandstone reservoir of the Toutunhe Formation, charging in 13 Ma to 8 Ma. Meanwhile, the source rock started to expel hydrocarbons and buoyancy drove the hydrocarbon via the Aika fault belt to migrate into sandstone reservoirs in the Toutunhe Formation. During the end of the Neogene, the paleo-oil reservoir in the Toutunhe Formation was destructed and hydrocarbons migrated to the sandstone reservoirs in the Ziniquanzi Formation; some paleo-oil reservoirs survived in the WDF. The burial pattern and change of reservoir wettability were major controlling factors of the sandstone reservoir-forming process. The buried pattern of the Toutunhe Formation in the western section of the southern Junggar Basin was "slow and shallow burial at early stage and rapid and deep burial at late stage". Hence, pore capillary pressure was extremely low due to limited diagenetic reformation (average pore capillary pressures were 0.26 MPa). At the same time, high content of chlorite coating increased the lipophilicity of reservoirs. Therefore, hydrocarbons preferably charged into the WDF with low matrix content (average 4.09%), high content of detrital quartz (average 28.75%), high content of chlorite films (average 2.2%), and lower pore capillary pressures (average 0.03 MPa). The above conditions were favorable for oil and gas enrichment. [ABSTRACT FROM AUTHOR]