Search

A plate heat exchanger (PHE) is a modern, effective type of heat transfer equipment capable of increasing heat recuperation and energy efficiency. For PHEs, enhanced methods of heat transfer intensification can be further applied using the analysis and knowledge already available in the literature. A review of the main developments in the construction and exploration of PHEs and in the methods of heat transfer intensification is presented in this paper with an analysis of the main construction modifications, such as plate-and-frame, brazed and welded PHEs. The differences between these construction modifications and their influences on the thermal and hydraulic performance of PHEs are discussed. Most modern PHEs have plates with inclined corrugations on their surface that create a strong, rigid construction with multiple contact points between the plates. The methods of PHE exploration are mostly experimental studies and/or CFD modelling. The main corrugation parameters influencing PHE performance are the corrugation inclination angle in relation to the main flow direction and the corrugation aspect ratio. Optimisation of these parameters is one way to enhance PHE performance. Other methods of heat transfer enhancement, including improving the form of the plate corrugations, use of nanofluids and active methods, are considered. Future research directions are proposed, such as improving fundamental understanding, developing new corrugation shapes and optimisation methods and area and cost estimations. [ABSTRACT FROM AUTHOR]

Increasing energy usage efficiency requires enhanced heat energy recuperation between process streams in the industry and civic sector with waste heat utilization. The condensation of different vapours is the process encountered in many industrial applications. Increasing the heat recuperation in this process is possible with efficient heat transfer equipment, among which a Plate Heat Exchanger (PHE) is at the leading position. A number of research works have been conducted in recent years concerning construction development and heat transfer enhancement in conditions of limited pressure drop to increase PHE performance in condensation processes. The results of studies on heat transfer and pressure drop in the two-phase condensing flow inside channels of PHE with different geometries of corrugations are discussed. In many implementations, the total pressure drop allowable for gaseous streams in heat exchangers is relatively small. The structure of two-phase flow in PHE channels of complex geometry is very different than in tubes and flat wall channels. The relative differences in approaches to enhance PHE performance in condensation processes based on its modelling, optimisation and design are analyzed. The directions and prospects for future developments are formulated, and potential savings for the economy and the environmental footprint is presented. [ABSTRACT FROM AUTHOR]

Pressure drop is an important consideration in Total Site Heat Integration (TSHI). This is due to the typically large distances between the different plants and the flow across plant elevations and equipment, including heat exchangers. Failure to consider pressure drop during utility targeting and heat exchanger network (HEN) synthesis may, at best, lead to optimistic energy targets, and at worst, an inoperable system if the pumps or compressors cannot overcome the actual pressure drop. Most studies have addressed the pressure drop factor in terms of pumping cost, forbidden matches or allowable pressure drop constraints in the optimisation of HEN. This study looks at the implication of pressure drop in the context of a Total Site. The graphical Pinch-based TSHI methodology is extended to consider the pressure drop factor during the minimum energy requirement (MER) targeting stage. The improved methodology provides a more realistic estimation of the MER targets and valuable insights for the implementation of the TSHI design. In the case study, when pressure drop in the steam distribution networks is considered, the heating and cooling duties increase by 14.5% and 4.5%. [ABSTRACT FROM AUTHOR]

To incorporate exchanger dimensions as a design objective in plate and fin heat exchangers, a variable that must be taken into consideration is the geometry of the finned surfaces to be used. In this work, a methodology to find the surface geometry that will produce the required heat transfer coefficient and pressure drop to achieve the design targets was developed. The geometry of secondary surfaces can be specified by the fin density, which represents the number of fins per unit length. All other geometrical features, as well as the thermo-hydraulic performance, can be derived from this parameter. This work showed the way finned surfaces are engineered employing generalised thermo-hydraulic correlations as a part of a design methodology. It also showed that there was a volume space referred to as volume design region (VDR) where heat duty, pressure drop, and dimensions could simultaneously be met. Such a volume design region was problem- and surface-specific; therefore, its limits were determined by the heat duty, the pressure drop, and the type of finned surface chosen in the design. The application of this methodology to a case study showed that a shell and tube heat exchanger of 227.4 m2, with the appropriate fin density using offset strip-fins, could be replaced by a plate and fin exchanger with any combination of height, width, and length in the ranges of 0–0.58 m, 0–0.58 m, and 0–3.59 m. The approach presented in this work indicated that heat exchanger dimensions could be fixed as a design objective, and they could effectively be achieved through surface design. [ABSTRACT FROM AUTHOR]

Energy is a fundamental element supporting societal development, particularly with the increasing dependency on the Internet of Things. It is also the main contributor to environmental impacts and subsequently, a potential sector for mitigation. Sustainable energy system design considers energy savings and energy efficiency, waste and consumption reduction, process efficiency enhancement, waste heat recovery, and integration of renewable energy. Emerging tools range from advanced Process Integration, modelling, simulation, and optimisation, to system analysis and assessment. This review covers selected emerging studies promoting sustainable system design, including the recent developments reported in the Special Issue (SI) of the 22nd Conference on Process Integration, Modelling and Optimisation for Energy Saving and Pollution Reduction (PRES'19). The primary emphasis was to enhance the economic and environmental performance. However, social factors were also highlighted as essential for future sustainable development. The discussion and analysis in this review focus on the most recent developments of (a) heat integration and heat transfer; (b) integrated and newly developed heat exchangers, (c) integration of renewables, and (d) roles in economic and environmental sustainability. The key results are highlighted, and future research ideas are suggested according to their links to a broader context. [ABSTRACT FROM AUTHOR]

Heat exchanger network (HEN) retrofit is a vital task in the process design to improve energy savings. Various types of heat exchangers such as shell and tube, double-pipe, compact plate, and spiral tube have their working temperature ranges and costs. Selecting suitable types of heat exchangers according to their temperature ranges and costs is a crucial aspect of industrial implementation. However, considering the type of heat exchangers in the HEN retrofit process is rarely seen in previous publications. This issue can be solved by the proposed Shifted Retrofit Thermodynamic Grid Diagram with the Shifted Temperature Range of Heat Exchangers (SRTGD-STR). The temperature ranges of six widely used heat exchanger types are coupled in the grid diagram. This diagram enables the visualisation of identifying the potential retrofit plan of HEN with heat-exchanger type selection. The retrofit design aims to minimise utility cost and capital cost. An illustrative example and a case study are presented to show the effectiveness of the method. [ABSTRACT FROM AUTHOR]

The design of heat exchanger networks (HEN) in the process industry has largely focused on minimisation of operating and capital costs using techniques such as pinch analysis or mathematical modelling. Aspects of operability and flexibility, including issues of disturbances affecting downstream processes during the operation of highly integrated HEN, still need development. This work presents a methodology to manage temperature disturbances in a HEN design to achieve maximum heat recovery, considering the impact of supply temperature fluctuations on utility consumption, heat exchanger sizing, bypass placement and economic performance. Key observations have been made and new heuristics are proposed to guide heat exchanger sizing to consider disturbances and bypass placement for cases above and below the HEN pinch point. Application of the methodology on two case studies shows that the impact of supply temperature fluctuations on downstream heat exchangers can be reduced through instant propagation of the disturbances to heaters or coolers. Where possible, the disturbances have been capitalised upon for additional heat recovery using the pinch analysis plus-minus principle as a guide. Results of the case study show that the HEN with maximum HE area yields economic savings of up to 15% per year relative to the HEN with a nominal HE area. [ABSTRACT FROM AUTHOR]