Search

Antenna chambers are RF‐shielded enclosures which are required for antenna and radio performance measurements. Typically, anechoic chambers (ACs) are used for measuring directional metrics (e.g. antenna pattern, effective isotropic power etc.), while reverberation chambers (RCs) are widely used for non‐directional measurements (e.g. antenna efficiency, total radiated power etc.). When a device under test requires both types of measurements, testing needs to be conducted sequentially in an AC and an RC. This leads to significant time inefficiencies due to the need to set up and calibrate two separate measurement setups in two different chambers. To address these issues, this letter proposes a programmable chamber framework capable of electronically switching between AC and RC modes by programming the reflective intelligent surface‐enabled sidewalls. This framework is highly attractive for the industry as it supports both directional and non‐directional measurements within a single chamber. The letter outlines the conceptual framework, discusses design considerations, and presents preliminary experimental validation of reflective intelligent surface‐enabled sidewall with the designed phase‐setting configurations to emulate the radio absorber sidewall of an AC and the metal plate sidewall of an RC. The experimental results demonstrate the effectiveness and potential of the proposed approach. [ABSTRACT FROM AUTHOR]

Automotive antennas are gaining importance due to their increasingly important role for autonomous driving with the development of the Internet of Vehicles. However, over‐the‐air testing on automotive antennas is difficult owing to its large volume and complex body structure. Plane wave generators can approximate uniform plane waves in the near field of the device under test, which can greatly reduce the measurement distance and thereby decreasing the cost compared with direct far‐field solutions. This letter designs three plane wave generators for three quiet zone sizes selected according to the vehicle structure at 5.9 GHz, achieving quiet zone sizes of 1.45 m ×0.23$\times 0.23$ m, 2.9m ×0.56$\times 0.56$ m, and 3.9 m ×1.27$\times 1.27$ m, respectively. Within the three quiet zones, amplitude deviations of 0.82, 0.34, and 0.34 dB and phase deviations of 9.4∘${9.4^\circ }$, 6.72∘${6.72^\circ }$ and 1.42∘${1.42^\circ }$ are realized, respectively, according to the numerical simulations. Uncertainty analysis is further implemented to investigate the robustness of the designed PWGs proposed in this letter. [ABSTRACT FROM AUTHOR]

The integration of directive elements into a circular switched parasitic array at 868 MHz is presented. The typical usage of reflective parasitic monopoles is supplemented with additional, shorter monopole elements which are positioned closer to the central active monopole to induce directive behaviour. This allows for more degrees of freedom with the steering of the antennas beam and to increase the gain of the antenna. This leads to a greater flexibility of the system and enables power reduction of the amplifiers for enhanced battery life time. The design and configuration of a circular switched parasitic array with directive elements is shown and a prototype is built for validation. [ABSTRACT FROM AUTHOR]

This letter presents a comprehensive analysis of the radiation behaviour exhibited by nine distinct on‐wafer radio‐freqeuncy (RF) probes used for device characterization in the mm‐wave bands of integrated circuits and antennas. The tested probes are sourced from two different manufacturers and feature various probe pitches. All probes are intended for use with the WR‐3.4 waveguide band ranging from 220 to 330 GHz. To the best of the authors' knowledge, such a detailed examination of RF probes operating in this band with respect to their radiation behaviour has not been demonstrated before. [ABSTRACT FROM AUTHOR]

Canonical objects with known radar cross section (RCS), for example, the trihedral corner reflector (TCR), play a crucial role in the calibration of automotive radar sensors. Moreover, these canonical objects are also used in the validation of simulated RCS obtained using asymptotic methods, such as hybrid geometric optics (GO) and the physical optics (PO) based methods. However, accurate RCS prediction with asymptotic methods is highly dependent on the individual scattering mechanisms considered in a simulation, for example reflection and diffraction from the TCR surfaces and edges, respectively. Reliable measurements are therefore required to evaluate if a particular interaction mechanism can be neglected to reduce computation complexity without adversely affecting the accuracy of the predicted RCS. In this letter, the monostatic scattering characteristics of three metallic TCRs are investigated with varying geometrical sizes in the E‐band, that is, from 60 GHz to 90 GHz. The ultra‐wideband (UWB) measurements, which offer a high delay resolution, can enable the identification of the individual scattering mechanisms. Diffraction from the TCR edges is experimentally demonstrated to contribute to a non‐negligible scattered power in this frequency band. [ABSTRACT FROM AUTHOR]

In this Letter, a tri‐reflector compact antenna test range (CATR) with a paraboloidal main reflector and two shaped sub‐reflectors is synthesised by the kinematic and dynamic ray tracing method, while the high cross‐polarisation isolation is achieved through the proposed system geometry. Numerical simulations by general responsibility assignment software patterns demonstrate that a cross‐polarisation isolation >40 dB and a peak‐to‐peak amplitude (phase) ripple <1 dB (10°) can be achieved on the principal cuts of the designed quiet zone at 90–325 GHz. This clearly shows that the high cross‐polarisation isolation in such a tri‐reflector CATR can be achieved by the proposed antenna geometry without depolarisation control in the shaping procedure. [ABSTRACT FROM AUTHOR]

A planar super‐wideband (SWB) antenna fed by an asymmetric coplanar strip is proposed, fabricated, and tested. The antenna consists of a hexagonal loop strip in which a signal strip is prolonged, curved, and shorted to a ground plane to facilitate SWB characteristics. In addition, by adding a boomerang‐shaped strip to the ground plane, the effective electrical length is increased, thereby decreasing the lowest operating frequency. The simulated results show that the proposed antenna exhibits a −10 dB reflection bandwidth from 1.18 to 49.22 GHz corresponding to a ratio bandwidth of 41.7:1. The measured results of the fabricated antenna are also represented and compared with the simulated results. The antenna gain changes from 2.05 to 10.62 dBi within the measured frequency range. [ABSTRACT FROM AUTHOR]

A quick review of the planar phaseless near‐field antenna measurement technique is presented and some interesting aspects related to the size of the mask used at the aperture of the antenna under test (AUT) are pointed out. It is shown simulatively and experimentally that due to the edge fields the AUT aperture's mask needs to be larger than the physical aperture of the AUT to achieve better accuracy. In addition, the misalignment of the setup has a big impact on the achieved far‐field accuracy. This is emphasised experimentally. [ABSTRACT FROM AUTHOR]

A novel and simple approach to adjust the polarisation properties of a microstrip patch antenna in the entire axial ratio (AR) range is proposed. The proposed antenna consists of a radiating patch and a parasitic strip separated into two parts, and the separated strip is placed at the outer perimeter of the patch for capacitive coupling. This structure enables the antenna to induce opposite‐direction currents on the strip, which allows flexible polarisation adjustment by moving the separated positions of the strip. For evaluation, two antennas with linear and circular polarisations are fabricated, and their performance is measured in a full anechoic chamber. The results prove that the proposed approach is suitable for flexible AR adjustment without a significant degradation of the matching characteristics and the design complexity. [ABSTRACT FROM AUTHOR]

A beam‐deflection short backfire antenna (BD‐SBA) is proposed. The BD‐SBA consists of an SBA and a deflection plate. The deflection plate is designed to change the phase of the reflected waves, hence deflecting the beam of the BD‐SBA. The beam deflection can realise different beam pointing within about 20°. An X‐band antenna (10 GHz) with a beam pointing of 12° is fabricated and tested. The measured results demonstrate that the desired beam deflection is obtained. A gain of 14.3 dBi and a sidelobe level of −20.6 dB are realised. The BD‐SBA, with a simple structure, low cost and moderately high gain, is suitable for the application of fifth‐generation wireless backhauling potentially. [ABSTRACT FROM AUTHOR]