Search

• Activated carbon derived from agriculture by-products obtain high surface area, high porosity, and low density. • Deionization efficiency of CDI, MCDI, and FCDI reached 80–90 % and water recovery rate 90 %. • The roller, spray coating, and mill ball grinding are useful to fabricate electrodes for industry applications. • The adsorption capacities of AC and AC-modified electrodes were 25–40 mg/g. • Life span and deionization efficiency of the flow electrode are higher than electrode plate. Capacitive deionization (CDI), membrane capacitive deionization (MCDI), and flow capacitive deionization (FCDI) are emerging technologies applied to remove ions from brackish water or saline wastewater based on electrode double layer (EDL) mechanisms. The electrode itself can be seen as the most important factor that determines the deionization efficiency of the CDI system. Electrode fabrication using activated carbon derived from agriculture byproducts is a useful solution to decrease cost, restrict environmental pollution, and enable agriculture waste recovery. In this review, the primary parameter's impact on activated carbon (AC) and the electrode fabrication process from the agriculture byproducts is detailed in a discussion to find the most optimal conditions. With excellent characteristics for the activated carbon such as a surface area of up to 2500 m2/g, it can be used to fabricate electrodes that have a high adsorption capacity of approximately 25 mg/g, able to be advanced to 40 mg/g with a modified AC. It can achieve a cycle performance of 95–97 %. The deionization efficiency of the CDI, MCDI, and FCDI systems can be up to 90 % with an input salt concentration from 2000 to 3000 mg/L where the water recovery ratio achieved is 50–90 %, alongside a salt rejection rate of about 7–75 %. AC can be modified to increase its special properties such as surface area, conductivity, and ion selectivity using different methods. The drawbacks and challenges of the CDI technology are also mentioned along with useful solutions such as electrode coating techniques using an anilox roller and a spray, for use in industry applications. [Display omitted] [ABSTRACT FROM AUTHOR]

Flow electrode capacitive deionization (FCDI) has great advantages in high salinity wastewater desalination. However, due to the limited adsorption capacity of electrode material, membrane concentration polarization would form and increase energy consumption, and affect the continuity of desalination. In this work, milling technology was used to modify original activated carbon (AC), the obtained ball milled activated carbon (BAC) was used as FCDI electrode material. The milling process modified multiple physical and electrochemical characteristics of original AC. The highest average salt removal rate (ASRR) of BAC was 2.2 times of that of AC, which was attributed to the modified surface properties including more oxygenated functional group, larger electrostatic gravitation characteristics and better hydrophilicity. The reduced concentration polarization during the desalination was responsible for the increased adsorption capacity, which was due to larger electrolyte contact area, enhanced ions capacity by more suitable pore structures, and 5 times higher energy normalized removal salt (ENRS) of BAC flow electrode than that of AC. Because of its simple operation and remarkable modification effect, ball milling technology shows great potential in large scale modification of electrode materials. [ABSTRACT FROM AUTHOR]

Abstract: The nanostructured anatase titanium dioxide/activated carbon composite material for capacitive deionization electrode was prepared in a short time by a lower temperature two-step microwave-assisted ionothermal (sol–gel method in the presence of ionic liquid) synthesis method. This method includes a reaction and a crystallization step. In the crystallization step, the ionic liquid plays a hydrothermal analogy role in driving the surface anatase crystallization of amorphous titanium dioxide nanoparticles formed in the reaction step. The energy dispersive spectroscopic study of the composite indicates that the anatase titanium dioxide nanoparticles are evenly deposited in the matrix of activated carbon. The electrochemical property of the composite electrode was investigated. In comparison to the pristine activated carbon electrode, higher specific capacitance was observed for the nanostructured anatase titanium dioxide/activated carbon composite electrode, especially when the composite was prepared with a molar ratio of titanium tetraisopropoxide/H2O equal to 1:15. Its X-ray photoelectron spectroscopic result indicates that it has the highest amount of Ti-OH. The Ti-OH group can enhance the wetting ability and the specific capacitance of the composite electrode. The accompanying capacitive deionization result indicates that the decay of electrosorption capacity of this composite electrode is insignificant after five cycle tests. It means that the ion electrosorption–desorption becomes a reversible process. [Copyright &y& Elsevier]

Capacitive deionization (CDI) is an emerging technology as a sustainable low energy process for desalination of brackish water. Activated carbon electrodes are often used in the CDI devices. Electrosorption capacity was found to be improved on asymmetric electrode configuration using activated carbon cloth doped with fluorine due to redistribution of electric potential. This led to improvement in desalination performance up to 12.4 mg/g for a desalination cycle of 6 min employing an asymmetric fluorinated electrode as cathode (ACC//F-ACC). A relatively high charge efficiency of 77 % was obtained representing 92 % charge efficiency neglecting the leakage currents. Furthermore, the ion adsorption rate was found to improve substantially due to an increased surface conductivity of the fluorinated electrode confirmed by Mott-Schottky analysis. Energy consumption during desalination of 1000 ppm sodium chloride solution of 0.71kWh/m3 for symmetric electrode configuration was found to reduce by 36 % upon employing asymmetric configuration. This study shows some of the benefits of asymmetric configuration to achieve an optimal operation of CDI device, as well as improvements related to energy consumption. Image, graphical abstract [ABSTRACT FROM AUTHOR]