Search

Objective: This work evaluates the functionalities of different superdisintegrants (SD) for manufacturing orodispersible mini tablets (ODMT) by direct compression., Methods: Twenty-three formulations varying in SD type, concentration, and lubricant were used to manufacture ODMT. The ODMT were then characterized for the following properties: friability, porosity, tensile strength, in vivo and in vitro disintegration time (DT)., Results: The results show that the presence, type, and concentration of SD did not influence friability, porosity, or tablet tensile strength. With regards to in vivo DT, only cross-linked poly (vinyl pyrrolidone) improved DT in all the tested formulations. Results also showed that when using microcrystalline cellulose (MCC) above 20% in the formulation, DT is longer. Cross-linked carboxymethyl cellulose accelerates DT when the MCC content is less than 20%. As for cross-linked carboxymethyl starch and calcium alginate showed no improvement on DT. Results for in vitro DT were all shorter than in vivo results and there was no correlation with the in vivo evaluation., Conclusions: This study shows that there is a need to develop better in vitro testing that precisely simulates in vivo conditions and that are adapted to ODMT. This standardization of the test methods for ODMTs must be accompanied by an improvement in the comprehension of SD mechanisms.

Context: High-amylose sodium carboxymethyl starch (HASCA) was recently proposed as a material for oral, sustained drug-release tablets prepared by direct compression. It was produced on a pilot scale, but appeared to be unsuitable for tableting and sustained drug release. Pilot-scale dry powder HASCA was dispersed in hot water and then precipitated with ethanol to give a dry powder presenting the required properties, but very high volumes of ethanol were used to recover the product., Objective: A process was therefore designed to transform totally amorphous pregelatinized HASCA by spray-drying into a suitable sustained drug-release excipient for matrix tablets while decreasing ethanol quantities., Results and Discussion: During the first manufacturing step, that is, heating of the initial hydro-alcoholic suspension, powder and water concentrations are key parameters for the acquisition of excellent binding properties. Hence, a variable ratio of amylose Vh, a crystalline polymorph of amylose, to the amorphous form, is observed depending on the key parameter values. As the most crystalline samples give the weakest tablets, binding properties do not appear to be linked to the presence of a Vh form of amylose. On the other hand, a high water concentration results in excessive tablet strength, that is, inverse conditions leading to the appearance of a Vh form of amylose. Finally, variations in hydro-alcoholic composition appear to affect only tableting properties and do not influence the drug-release rate., Conclusion: A process designed to transform totally amorphous pregelatinized HASCA by spray-drying is proposed for easier, economical industrial HASCA production.

A study to enhance the dissolution rate of ibuprofen, a poorly water-soluble drug, was carried out through combining specific formulations and processes with the addition of a hydrophilic carrier for the preparation of microparticles. Microparticle production was performed by spray drying ibuprofen microsuspensions formulated in an aqueous system with the addition of ethanol containing Aerosil 200 and Tween 80. We were able to consistently produce microparticles as much as 40% of the dry weight of the input microsuspension. Spray-dried microparticles were characterized by scanning electron microscopy, X-ray diffraction, differential scanning calorimetry, laser diffractometer mastersizer, and infrared spectroscopy. No modification to the crystalinity and chemical structure of ibuprofen was observed. Dissolution of ibuprofen microparticles reached 100% in 3 minutes compared with less than 10% for unmodified ibuprofen. We concluded that both by the modification of formulation and the spray drying process it is possible to increase the dissolution rate of the tested model drug.

Because psychrometry takes into account a great number of variables reflecting the quality of the drying air, it is an interesting tool to improve the control and the optimization of the spray drying process. In this article the authors study the evolution of the psychrometric variables according to the values taken by four inlet parameters (inlet air temperature, liquid flow rate, solid concentration of the spray dried liquid, and nature of the product). The results highlighted the existence of mathematical models making it possible to optimize the process, but also to underline the influence of the nature of the product on the drying mechanism.