Search

this paper analyses the numerical and experimental results to evaluate the dynamic properties of pultruded GFRP (Glass-Fiber Reinforced Polymers) buckled columns. The profiles are made of glass fiber reinforcement and thermosetting vinylester matrix with thin-walled open or closed cross section. The buckling phenomena of the column with fixed ends were evaluated with a non-destructive method based on experimental modal data through dynamic identification procedure. Numerical analysis has been carried out through Finite Element models calibrated considering two consecutive stages that involve the local and global scale: i) parametric natural frequencies analysis to model the different cross sections taking into account the sti f fness of the rotational constraint between the wall segments of the thin walled pultruded profiles; ii) buckling analysis to identify the inaccuracies in the specimen or in the experimental apparatus through global flexural displacements which increase continuously with the axial load. Experimental, theoretical and numerical results were compared in order to know the wall segment effects of GFRP columns in free vibration field when affected by buckling phenomena. The results allow to investigate the significant role that the manufacturing imperfections of pultruded material play in the structural performance of GFRP buckled columns. [ABSTRACT FROM AUTHOR]

The kink behavior of non-slender glass fiber-reinforced epoxy prismatic specimens of variable length and fiber volume fraction at temperatures ranging from 25 °C to 125 °C was investigated. Splitting failure occurred at the glassy state while kinking failure was observed at the glass transition state and buckling with subsequent post-peak kinking at the rubbery state. Kink initiation was caused by the initial imperfections, i.e. the waviness of the unidirectional fibers. Initiation occurred through fiber microbuckling caused by combined compressive and shear stresses at the glass transition state and predominant shear stresses at the rubbery state due to the preceding buckling. The kink band width was narrow at the glass transition state due to the significant compressive stresses and corresponded to the wavelength of the initial fiber waviness. The kink band width at the rubbery state was much wider and corresponded to the band width of the maximum shear stresses at the inflexion points of the buckling shape. The kink band angle depended on the ratio of compressive to shear stresses. The different specimen slendernesses and fiber volume fractions did not influence the kink initiation and kink band formation mechanisms. [ABSTRACT FROM AUTHOR]

Abstract: Glass fiber reinforced polymer (GFRP) composites are used extensively to strengthen and/or to rehabilitate infrastructures. The current study focuses on the use of GFRP for enhancing local buckling behaviour of wide flange steel beams. The study is conducted numerically using a nonlinear finite element model developed in-house. In the numerical model, consistent shell elements are used to simulate the flanges and web of the steel beams as well as the GFRP plates. The interface between the steel and GFRP plates is simulated using a set of continuous linear spring systems representing both the shear and peel stiffness of the adhesive based on values obtained from a previous experimental study. The numerical model is validated using test results and numerical predictions available in literature. Various failure modes, including GFRP rupture, adhesive shear failure, and local buckling of the flanges of beams are included in the model. The effect of geometric imperfection and residual stresses are also included. The model is then used to conduct a parametric study to assess the effect of bonding GFRP plates on enhancing the local buckling behaviour of wide flange steel beams. The results reveal that the effectiveness of this approach especially for the case of slender beams. [Copyright &y& Elsevier]

Abstract: This paper focus on the design of a GFRP truss-like structure for dismountable bridges with maximum span of 30m. The bridge structure is composed of a deck supported by prestressed trussed beams which are mounted by assembling GFRP tubular profiles and steel joints with bearing type connections. Experimental tests were carried out on short profiles to determine their compressive strength at the connections and on two 1:2.3 reduced models of the trussed beam structure: a short 1.3m span cantilever beam and a 13.0m span simple supported beam. The main results obtained from the performed experimental tests on short profiles and on the cantilever beam are presented herein. It is shown that a non-linear behaviour can be generated on the trussed cantilever beam by decompression of tubular members and that collapses are induced by buckling of diagonal members. [Copyright &y& Elsevier]