Search

In this paper, the morphology, attractive force ( F at ), adhesive force ( F ad ) and Young's modulus ( E Y ) of diesel in-cylinder soot particles sampled by a total cylinder sampling system were studied using atom force microscopy. In each combustion phase, the equivalent diameter ( ED ), F at , F ad , adhesion energy and E Y present broad distributions. The pattern of ED distribution in the late combustion phase is similar to that in the late diffusion combustion phase, especially in the range of ED < 10 nm, suggesting that the particle size distribution changes little after the late diffusion combustion phase. Most isolated soot particles in each combustion phase possess a very low sphericity ratio. Three types of force curves are discovered for in-cylinder particles, and are introduced to identify the particle types. For the test carbonized soot particles, the SR appears to increase with an increase in ED in each combustion phase, and the AED shows a similar trend to that for all test particles during the combustion process. Due to the presence of plastic deformation for the nascent soot particles and the penetration for the liquid materials during the force measurement, the carbonized primary soot particles are employed for force analysis. As the combustion proceeds, the population-averaged values of F at and F ad show opposite trends; the attractive force, which is mainly driven by the Van der Waals force, gradually decreases. During the combustion process, the population-averaged adhesion energy decreases to a minimum in the late premixed combustion phase after which it then increases. The initial increase in the population-averaged Young's modulus ( AE Y ) is followed by a decrease before gradually increasing again from the early diffusion combustion phase. The AE Y shows a negative correlation with the fringe separation distance in the soot structure. [ABSTRACT FROM AUTHOR]

Abstract: The nanostructure, fractal dimension and size of in-cylinder soot during diesel combustion process have been investigated for a heavy-duty direct injection diesel engine, using a total cylinder sampling system followed by high-resolution transmission electron microscopy and Raman scattering spectrometry. Different structural organizations of in-cylinder soot are found depending upon the combustion phase. It is revealed that both the fringe tortuosity and separation distance decrease as combustion proceeds, while the mean fringe length increases distinctly from 1.00 to 2.13nm, indicating the soot evolution toward a more graphitic structure during the combustion process. The fractal dimensions of aggregates are in a range of 1.20–1.74 at various crank angles under the applied engine operating conditions. As temperature and pressure increase, the fractal dimension decreases significantly to a minimum at the early diffusion combustion stage. The soot particles become more compact again as the fractal dimension increases during the subsequent combustion period. Primary particle sizes start small, go through a maximum in the early diffusion combustion phase and decline again as combustion proceeds. [Copyright &y& Elsevier]

Abstract: The diesel soot was extracted from the chamber of a running diesel engine using a total cylinder sampling system. A structural description and size distribution of the soot spherules were performed by means of high-resolution transmission electron microscopy (HRTEM). HRTEM image analysis was carried out to achieve semi-quantitative information about the soot organization. Different nanostructures were found in dependence upon the engine test conditions. A better organization of the graphitic layers occurred for the in-cylinder soot as the expansion stroke developed. The oxygen concentrations at sampling angles and the cylinder pressure were measured. The oxidation rates of the in-cylinder soot during the late combustion phase were calculated according to the differences of spherules size distributions between two consecutive sampling angles. The soot reactivity in dependence on the nanostructure was shown after deducting the effect of oxygen concentration and temperature. The increase of resistance toward oxidation was associated to the increase of the structural order for the in-cylinder soot. The results are a useful database for testing the structure–property relationship between the nanostructure and the reactivity of the in-cylinder diesel soot. [ABSTRACT FROM AUTHOR]

Experiments were performed on a CH 4 lean premixed flame to better understand the effect of the oxidation-induced fragmentation of primary particles on soot oxidation reactivity. An aerosol generator was used to homogeneously disperse diesel soot into the flame. Because minimal soot was formed in this flame itself, the information about diesel soot fragmentation was readily obtained. The thermophoretic and probe sampling techniques were used to obtain soot particles at various heights above the burner. The particle size distribution, oxidation reactivity, nanostructure and carbon chemical state of each sample were characterized. The soot reactivity was evaluated in terms of activation energy. The results indicate a higher extent of aggregate fragmentation occurs at moderate soot burnout percentages and that the internal structure in soot is not destroyed during aggregate fragmentation. At higher soot burnout percentages, the internal burning produces more primary particle fragmentation, so that the soot particles exhibit an increase in fringe tortuosity and decreases in fringe length and sp2/sp3 hybridization ratio. These variations in physicochemical properties increase the oxidation reactivity of the soot particles. [ABSTRACT FROM AUTHOR]