Search

Sulfide wastewater that is anthropogenically generated from industrial activities is highly corrosive, hazardous, and harms the natural ecosystem. This study uses a novel fluidized-bed homogeneous crystallization (FBHC) method to remove sulfide ions from an aqueous solution. Zinc is used as a precipitant to crystallize ZnS homogeneously in the FBHC reactor to reduce the sludge, which is commonly produced in a conventional chemical precipitation process. The optimal pH value, [Zn2+]0/[S2-]0 molar ratio, sulfide cross-sectional surface loading (L, kg-S/m2.hr), and hydraulic retention time (HRT) for the system are established, to optimize the sulfur removal efficiency. The maximum crystallization ratio and the total removal efficiency for sulfur are 97.7% and 98.8%, respectively, at pH = 5.4, a [Zn2+]0/[S2-]0 molar ratio of 1, a cross-sectional surface loading of 2.2 kg-S/m2.hr, and an HRT number of 6 with an initial sulfur concentration of 320 mg/L. The solid products are collected and identified as zinc sulfide (wurtzite) using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS).

Magnetically separable spinel ferrites were created in an electrocoagulation (EC) process for removing boron from aqueous solution. Coprecipitates of NiFe2O4, CoFe2O4 and CuFe2O4 were obtained using sacrificial iron anodes (EC-Fe) in an electrolyte that contained transition metal salts (Ni, Co, Cu). The use of nickel chloride (NiCl2) as the supporting electrolyte yielded the highest boron removal since the maximum adsorption capacity of the resulting sludge was 28.9 mg-B/g. An EC that used iron and nickel as anodes (EC-Fe/Ni) in NaCl electrolyte was then employed to form nickel ferrite by electrochemical dissolution of ferrous (Fe(II)) and nickel (Ni(II)) ions, providing comparable removal efficiency but minimizing the residual level of Ni(II) in the treated water. The saturation magnetization of the precipitate that was produced in the EC-Fe/Ni system was 50.3 emu/g which exceeded that in the EC-Fe system with nickel chloride – 21.8 emu/g, indicating its outstanding magnetic separability. EC-Fe/Ni was optimized to remove 95% of boron from solution in 60 min with an initial boron concentration of 10 ppm at pH 8 and a current density of 3.75 mA/cm2.

Excessive and industrial advances have increased fluoride quantity in the effluents. However, the environmental carrying capacity for fluoride is relatively slim immediately affecting both aquatic and terrestrial animals while its transport can further contaminate the water source. To protect the public and the environment, different environmental agencies globally set their respective effluent standard restricting F- concentration to 15 mg/L as the median value. However, various processes from previous investigations have mostly been limited in treating 100–1000 mg F-/L with secondary pollution commonly overlooked. Re-assessing the available defluoridation technologies, chemical precipitation has still been the most feasible among the technologies, especially extremely high fluoride concentrations. In this study, fluoride removal through chemical precipitation was investigated using conventional precipitation and fluidized-bed homogeneous crystallization. Parameters such as a wide range of initial concentrations from 100 to10,000 mg/L and pH 2.0–11.0 under conventional precipitation were varied and analyzed. To reduce high water content sludge, a 550-mL cylindrical glass was modified to simulate a fluidized-bed reactor to investigate homogenous crystallization varying influent concentration, bed-support size, and fluid flow. Results showed that chemical precipitation could effectively remove fluoride even at very high fluoride concentrations ranging from 1,000 to 10,000 mg/L. Alternatively in the fluidized-bed granulation process, an initial very low flow without recirculation flow was required to initiate particle formation. The predominant size of the recovered particle was

Spent ion exchange resins have become a crucial radioactive solid waste from the nuclear industry. Developing effective and safe disposal methods as alternatives to the present cementation method remains challenging. This investigation demonstrates the treatment of a mixed resin (sulfonated and quaternary ammonium polystyrene beads with a weight ratio of 40%:60%) by the electro-Fenton process. Mesh-type titanium metal that was coated with IrO 2 /RuO 2 (Ti-DSA) was used as the anode and a stainless steel net was used as the cathode. The conversion of resins to soluble fragments and the removal of total organic carbon reached 92% and 99.4%, respectively, under conditions of solid loading = 40g L −1 , pH 2, applied current = 2 A, H 2 O 2 flow rate = 1.2 mL min −1 , FeSO 4 = 20 mM at 85 °C. A pseudo first-order kinetic model of consecutive reactions specified that the efficacy of the electro-Fenton depended strongly on the slowly generated styrene in the aqueous phase by H 2 O 2 and strong acid, which was rapidly mineralized by the hydroxyl radicals. The electro-Fenton process with reused iron catalyst was effective for treating ion exchange resin for at least for three runs, greatly reducing the volume of waste resin liquid.

Most of nutrients in municipal wastewater originate from human urine. In this study, a novel fluidized-bed homogeneous crystallization process was developed for the simultaneous recovery of phosphorus (P) and potassium (K) from synthetic human urine. The operational variables including pH, Mg:K ratios and up-flow velocity were tested in the laboratory. The total removal of P and K (TR%) reached 98.4% and 70.5%, respectively, and the crystallization ratios (CR%) were 86.5% and 62.3%, respectively, at conditions of pH 10 ± 0.2, molar ratio Mg:K = 1.25, initial concentrations 850 mg P/L and 1830 mg K/L. The SEM and XRD analyses showed that the fluidized bed homogeneous crystallization (FBHC) product was pure magnesium potassium phosphate (K-struvite) (average size = 0.85 mm; purity = 95 ± 3%). The modelling of minimum fluidization velocity (MFV) resulted in values of up-flow 1.5–2.0 times the MFV for the effective fluidization. The profit of the recovery of P and K from human urine via FBHC process could be $0.26/m3-urine.

The granulation of calcium carbonate (CaCO3) exhibited high industrial demand due to its wider application and importance in cement, paper, glass and steel manufacturing. This paper investigated the granulation kinetics of CaCO3 through the fluidized-bed homogeneous granulation (FBHG) process during the homogenous nucleation stage. The CaOH solution was used as source of Ca2+ reactant, while K2CO3 solution as source of CO32− precipitant. The mechanism followed the pseudo-second order kinetics. The calcium cation attracts the carbonate anion to form CaCO3 through a double displacement chemical reaction. The calcium-is-to-carbonate molar ratio ([Ca2+]/[CO32−]) was varied into 1.25 to 2.50, with constant values of pH = 10 ± 0.2, influent carbonate concentration = 10 mM and total influx flow rate = 60 mL min−1. The ideal [Ca2+]/[CO32−] condition was found to be at 1.50 that means the precipitation of CaCO3 grew and stayed inside the reactor. At the same condition, granules of diameter size of 1 mm to 2 mm were collected with a subrounded shape and smooth surface as shown by its surface morphology. The characterization analysis also verified the high purity of CaCO3-aragonite granules precipitated through the FBHG process.

This work demonstrated the removal of lead (Pb) from aqueous solution using fluidized-bed crystallization (FBC, using silica sand as seeds) and fluidized-bed homogeneous crystallization (FBHC, without seeds) systems. Synthetic lead wastewater with concentrations of 10, 40 and 200 ppm were treated. The results thus obtained indicated that effluent pH was an essential parameter in determining the efficiency of FBC and FBHC. A comparison between theoretical solubility and residual Pb in effluents revealed that FBHC in the predictable metastable region of pH 6.5–8.5 guaranteed 99% Pb removal and a crystallization ratio of 95% (CR%). XRD analysis suggested that the lead carbonate of FBHC products comprised either a cerussite (PbCO3) or a hydrocerussite (Pb3(CO3)2(OH)2) phase, depending on pH. FBHC was proven to be effective in remediating lead wastewater under optimal hydraulic conditions (initial molar ratio of [Na2CO3]/[Pb] > 1.2, upflow velocity = 25–35 m h−1 and pHe = 7.2 ± 0.4), which were all similar to those in FBC. The cross-section loading (L, kg m−2 L−1) depended on the input Pb level; L was controlled at 0.15 kg m−2 h−1 for treating 10 ppm-Pb and was increased to 5.73 kg m−2 h−1 for 40 and 200 ppm-Pb, optimizing the FBHC and FBC processes. Without the addition of seed materials, FBHC recovered purer lead carbonate than did FBC.